Kenmore / Sears Dishwasher Hose Or Tube

This adjustable manifold connects the upper rack to the dishwasher's rear water feed. It channels wash water to the upper spray arm and maintains a sealed connection as the rack height changes for consistent cleaning performance. What it does:

• Routes water from the rear feed tube to the upper/middle spray arm
• Self-adjusts with rack position to keep a secure, leak-resistant connection
• Replace if cracked, deformed, or the coupling no longer seals
• Common symptoms include poor cleaning on the upper rack, weak spray, upper spray arm not turning, or a small leak at the back of the tub

• 1 adjustable manifold

• Disconnect power and shut off water; wear gloves for protection
• Remove the upper rack by releasing the rail end caps and sliding the rack out
• Unclip the manifold from the rack and disengage it from the rear feed port; seat the new manifold fully
• Reinstall the rack and ensure the spray arm spins freely

12 Ft in length

This drain hose channels used water from the appliance's drain pump to the household plumbing. Replacing a cracked, kinked, or clogged hose stops leaks and helps your unit drain correctly at the end of the cycle.

• Directs wastewater from the drain pump to the home drain system
• Helps maintain proper outflow during the drain portion of the cycle
• Common symptoms: standing water after a cycle, water on the floor, drain error codes, visible cracks or kinks in the hose
• Old hoses can become brittle, split, or obstructed over time

• Disconnect power; shut off water supply if applicable
• Place towels or a pan to catch residual water when removing the old hose
• Note original routing; install the new hose without sharp bends or kinks and secure all connections with existing clamps or appropriate replacements
• Run a test drain/cycle and check every connection for leaks

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation

This faucet adapter threads onto a compatible sink faucet to provide the connection point for an appliance's quick-connect hose, creating a secure, watertight hookup during filling and operation. What it does:

• Adapts faucet spout threads to accept the appliance hose/coupler
• Helps prevent leaks and drips at the faucet connection
• Replaces a worn, stripped, or missing adapter
• Common fix when a quick-connect hose (e.g., on a portable appliance) won't attach or pops off

• 1 faucet adapter

• Turn off water and remove the existing faucet aerator before installing
• Hand-thread the adapter carefully to avoid cross-threading; snug gently if needed with a non-marring tool
• Attach the hose/coupler and slowly open the faucet; check for leaks and retighten if necessary

The Drain Hose is an OEM part for Whirlpool dishwashers. This hose works to divert wastewater from the dishwasher to the garbage disposal or drain pipe beneath the kitchen sink.

The drain hose is responsible for safely transporting soapy water, food debris and other particles away from the washing cavity during each cycle. It prevents leaks and backup within the dishwasher tub.

Causes of a bad drain hose can include cracks, splitting, or deterioration of the plastic tubing over many years of use. Clogs within the hose are also problematic.

Symptoms of a failed drain hose include:

• Puddles or leaks developing beneath the dishwasher
• Inability to fully drain wash and rinse water after cycles
• Fault codes showing drainage issues

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Replacement fill hose that routes water from the household supply to the appliance's ice maker and water dispenser, restoring proper water delivery and helping prevent leaks or pooling from a damaged line. What it does

• Directs water from the inlet valve to the ice maker and dispenser for ice production and dispensing.
• Maintains steady water flow; prevents kinks and pinched lines that reduce flow.
• Replace if cracked, split, collapsed, or leaking.
• Common symptoms: reduced or no water to the dispenser or ice maker, visible leaks, or pooling under/behind the appliance.

• Turn off the water supply and disconnect power before servicing to avoid flooding and electrical hazard.
• Inspect and replace clamps or fittings as needed; ensure proper seating and a snug, leak-free connection without overtightening.
• Check for kinks in the hose and route it so it won't be pinched by the appliance or cabinetry.
• After installation, turn the water back on and test for leaks at all connections.

Contains two, six foot long braided hoses with 90 degree ends.

This replacement hose restores a secure, leak-resistant path for air or condensate in your appliance. Replacing a cracked, kinked, or brittle hose helps maintain proper flow, prevents leaks, and supports overall performance.

• Channels air or water as designed to ventilate or drain the unit
• Helps maintain a sealed connection at fittings to minimize leaks
• Flexible design supports correct routing without sharp kinks
• Common symptoms: visible cracks or brittleness, kinks, leaks, poor draining or reduced airflow

• Disconnect power and, if applicable, shut off water before servicing; allow components to cool.
• Place towels/containers to catch residual water; wear gloves to protect from sharp edges.
• Transfer and reuse existing clamps/adapters if required; replace any worn seals or clamps.
• Route without sharp bends; fully seat and secure both ends; test for leaks or airflow after installation.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Size: 7 foot long.

This manifold channels wash water within the dishwasher's spray system. Replacing a damaged or clogged manifold helps restore proper water flow and cleaning performance while reducing the chance of leaks at internal connection points.

• Routes high-pressure wash water through the dishwasher's spray system
• Maintains a sealed path to help prevent internal leaks
• Supports consistent spray pressure for effective cleaning coverage
• Helps resolve symptoms such as poor cleaning, weak spray, leaks, or visible cracks in the manifold

• Disconnect power and turn off the water supply before servicing
• Access from inside the tub; remove racks or panels as needed to reach the manifold
• Release retaining clips/screws and note the manifold's orientation; inspect any related seals/O-rings and replace if worn
• Reassemble and run a short cycle to check for proper spray and leaks

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

This stainless-steel braided dishwasher connector links your home's water supply to the dishwasher inlet. The 72-inch length and 3/8 in Comp x 3/8 in MIP fittings provide a durable, properly sized connection for installations using these ends.

• Connects the shutoff/angle stop to the dishwasher inlet
• 72-inch length accommodates routing through cabinets and tight spaces
• Braided stainless-steel jacket for durable service
• Replace if you notice leaks at the hose or fittings, visible corrosion/fraying/kinks, or slow/no fill from restriction

• Disconnect power and shut off water at the supply valve before starting
• Place a towel or pan to catch residual water
• Start all threads by hand to avoid cross-threading; tighten with a wrench until snug—do not overtighten
• Use thread sealant only on tapered pipe threads if required; do not use on compression seats. Open the valve slowly and check for leaks.

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

The Drain Hose is an OEM part for Frigidaire dishwashers. This part ensures that water flows smoothly and consistently out of the dishwasher after each wash and rinse cycle, preventing backflow, leaks, and potential water damage. 

Causes of a bad Drain Hose can range from physical damage, such as cracks or punctures that occur over time or through misuse, to clogs formed by food particles or grease that restrict water flow.  

Symptoms of a malfunctioning Drain Hose include:

• Water not draining properly from the dishwasher, leading to standing water after cycles
• Leaks detected around the dishwasher, which may indicate cracks or holes in the hose
• Kinking or blockage within the hose that impedes water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.