Kenmore / Sears Dishwasher Parts

This electronic control board coordinates key refrigerator operations for consistent, reliable cooling performance. When the original board fails, replacing it restores the control logic that manages temperature regulation and other critical functions. What it does

• Regulates cooling cycles and defrost timing
• Controls and monitors the compressor and fan motors
• Processes sensor feedback and user control inputs
• Address symptoms such as not cooling, warm temperatures, unresponsive controls, or random cycling

• One electronic control board

• Disconnect power to the refrigerator before servicing; observe ESD precautions and handle the board by the edges
• Access the control compartment; photograph wiring and transfer connectors one at a time
• Verify all connections are fully seated and mounting points are secured
• Some models may require a control reset or initialization—follow the unit's tech sheet or service instructions

The Control Board is an OEM component for Whirlpool dishwashers. As the central "brain" located under the dishwasher tub, this printed circuit board orchestrates all wash cycle functions and settings. 

Symptoms of a bad control board include:

• Failure to turn on or select desired cycles  
• Glitches in display readouts 
• Inability to advance cycles or unwanted resets
• Circuit board humming or buzzing noises

Causes of a bad control board can include water intrusion or prolonged exposure to steam damaging sensitive electronic components over time.

Replace with this Whirlpool board to restore reliable programming and dependable dish cleaning. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

The Hinge Lever (LH) is an OEM part for Bosch dishwashers. This left-hand lever is responsible for assisting in the opening and closing of the dishwasher door through a pivoting motion. The hinge lever works with other door components like springs and cables to provide smooth, balanced movement of the door. 

Symptoms of a bad Hinge Lever include: 

• Difficulty opening or closing the dishwasher door  
• The door not staying securely closed during the cycle
• Excessive noise or creaking coming from the door area
• Misalignment of the door 

Causes of a bad Hinge Lever can include normal wear and tear over time, damage from excessive force or weight on the door, or loose mounting hardware.

Note: Left hinge lever

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This replacement latch secures the door closed so the appliance can operate correctly. Restores a positive close and consistent door recognition to help prevent no-starts and intermittent operation. What it does / common symptoms:

• Engages the strike to hold the door/panel closed
• Ensures the door-closed signal is made so controls can run
• Worn or broken latch may cause the door not to stay shut
• Unit may not start, show a "door" message, or stop if the door is bumped

• 1 latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch per model—typically behind the front panel or inner door liner
• Note and transfer any springs/clips from the original latch to the new one
• Verify smooth open/close and proper strike engagement before testing operation

Dishwasher middle wash arm manifold tube holder. This holder will have a split at the 3:00 position for easy removal from the manifold tube.

Replace a damaged or missing silverware basket with this dishwasher basket. It organizes and separates flatware and small utensils so water can reach each piece, improving cleaning results and keeping items contained throughout the wash.

• Holds and separates silverware and small utensils during the dishwasher cycle
• Helps keep pieces upright for better spray coverage and cleaning
• Replace if the basket is cracked, warped, or has broken grid sections that let utensils fall through
• Also replace if missing or if the basket no longer stays securely in place

• Turn off power to the dishwasher before working inside
• Remove the old basket and place the new basket in the designated location for your model
• Ensure spray arms rotate freely with the basket installed
• Load utensils per your owner's manual for best results

Color: light gray. Each prong goes out about 10 inches from the center.

This kit includes 4 double roller attachments. Enough for one lower rack. Color: white. Each roller attachment measures about 3 inches high by 6 inches deep.

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

• Rack that will not fully extend or retract
• Binding or sticking during rack movement  
• Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain Hose is an OEM part for Whirlpool dishwashers. It serves as the connection that allows dirty water to exit the dishwasher tub and flow into the water drain system after each wash cycle. The hose transports wastewater from inside the dishwasher out through the standpipe.

Causes of a bad drain hose can include mineral or food debris buildup blocking water flow within the hose, cracks or breaks in the plastic material from repeated bending, or a loose or damaged hose clamp connection.

Symptoms of a drain hose failure include:

• Standing water remaining in the bottom of the tub after a cycle
• Puddles or leaks developing near or underneath the dishwasher
• Water failing to properly drain during the designated drain portion of cycles
• Kinks or sagging appearing in the hose affecting water drainage

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

Overfill control.

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This is a circulation pump motor for dishwashers. It controls the main pump of the appliance.The pump is directly responsible for removing extra water from the dishwasher after use. When a dishwasher's circulation pump motor goes bad, the main indicator is usually leaking from the appliance. There will be a noticeable amount of water emerging from the bottom of the machine whenever the cycle is engaged. Unplug the dishwasher from its main power source and water hookup. Remove the dishwasher from its space in the counter. Remove all necessary entry plates to access the interior of the dishwasher. There is a metal bracket holding the current motor in. Unscrew the two screws that secure the bracket and remove this component. Remember which way the motor is oriented before removing it. Unplug the power cable connecting the motor to the dishwasher. Put the two new sealing rings on the new pump motor. Repeat these instructions in reverse to install the new part.This Frigidaire dishwasher circulation pump motor is a genuine OEM replacement part sourced directly from Frigidaire. The pump motor is sold individually. This part is compatible with Frigidaire, Kenmore, Westinghouse, and Gibson appliances.

This rack adjuster assembly restores secure support and adjustable height for the dishwasher's upper rack. Replacing a worn or broken adjuster helps keep the rack level and sliding smoothly for easier loading and consistent wash performance. What it does:

• Supports and locks the upper rack at the selected height
• Allows smooth in-and-out movement when intact
• Helps prevent the upper rack from dropping, tilting, or feeling loose
• Common failure signs: rack won't raise/lower, falls off track, binds or feels rough

• One rack adjuster assembly

• Disconnect power to the dishwasher; shut off water supply
• Pull out the upper rack and remove end caps/stops before lifting the rack off the rails
• Release the old adjuster's locking tabs and install the new assembly in the same orientation
• Reinstall rack stops and test rack height adjustment and movement before restoring power