Kenmore / Sears Dishwasher Parts

2 clamps included.

This nozzle assembly directs high-pressure wash water through its jets for even cleaning inside the dishwasher. Replacing it restores consistent spray coverage and wash performance. What it does:

• Distributes wash water through spray jets during wash and rinse cycles
• Uses water pressure to rotate and reach all rack areas
• Replaces broken, warped, or clogged nozzles that restrict flow
• Common symptoms include poor cleaning results, spray arm not spinning, unusual noise, or leaks at the spray hub

• 1 nozzle assembly

• Disconnect power and water supply before servicing
• Pull out the rack as needed; release the locking tab or nut to remove the old nozzle
• Inspect and transfer any O-rings/gaskets if present; seat the new assembly fully for a leak-free seal
• Run a short test cycle to check for leaks

The Electronic Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, this board regulates all wash and rinse cycles according to preprogrammed instructions. It communicates timing and commands to other crucial components.

Symptoms of a faulty control board include: 

• Failure to power on or unresponsive touch controls  
• Inability to select or advance through wash cycles
• Noise or vibration issues from improper component operation 
• Error codes appearing repeatedly on the digital display

Causes can involve water intrusion corroding circuits or individual component failure due to prolonged operation. Over time, environmental factors may inhibit board performance.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This replacement door spring maintains proper tension so the door opens smoothly and doesn't drop. Replace a weakened or broken spring to restore controlled, balanced door movement and everyday usability. What it does:

• Provides tension to balance the door's weight during opening and closing
• Helps prevent the door from slamming open or falling unexpectedly
• Common fix for a door that feels heavy, drops open quickly, or won't hold a mid-position
• Replaces springs that are stretched, fatigued, or broken

• 1 door spring

• Disconnect power before servicing; springs are under tension—use gloves and eye protection
• Note the spring's routing and hook positions; take a photo before removal
• Use pliers to release and attach the spring carefully to avoid sudden release
• Some models use two springs; replace both for even tension if applicable

This door seal fits into the dishwasher's tub channel around the door opening. It compresses when the door closes to contain wash water and steam, helping prevent front-door leaks and maintain quiet, efficient operation. What it does:

• Creates a watertight seal between the dishwasher door and tub during cycles
• Helps keep water and steam from escaping; reduces operational noise
• Wear may show as drips at the door, moisture on the floor, or visible cracks/flattening
• Contributes to the door not sealing evenly

• 1 door seal

• Disconnect power and turn off the water supply before service
• Open the door, pull the old seal straight out of the channel, and clean the groove
• Warm and straighten the new seal; start at the top center and press evenly into the channel without stretching
• Close the door to help seat the seal and check for leaks on the next cycle

Includes one sprayarm.

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This line cord supplies electrical power from the wall outlet to the appliance. Replacing a worn, cut, or heat-damaged cord restores safe, reliable power and can help resolve no-power or intermittent operation issues.

• Delivers AC power from the outlet to the unit's electrical system
• Helps correct no-power or intermittent power when the cord is moved
• Ideal replacement for cords with cuts, fraying, or burn/discoloration on the plug
• Supports proper grounding and safe operation when installed correctly

• Disconnect power before servicing; ensure the appliance is fully de-energized
• Match wire routing and connections to the product's wiring diagram; ensure a secure ground
• Use an appropriate strain relief if required by the product to prevent abrasion
• Route the cord away from sharp edges, moving parts, and hot surfaces

The Sensor is an OEM replacement part for Bosch dishwashers. It detects soil levels through cycles, automatically adjusting water volumes and times for optimal cleaning. Precise sensing reduces overwashing.

Causes of a bad sensor involve general deterioration from continuous usage monitoring wash parameters thousands of times. Dirt or debris accumulation triggers false readings, decreasing efficiency.

Symptoms of a bad sensor include:

• Extended cycle times as improper inputs cause system delays  
• Inconsistent wash results relying on default static cycle settings
• Error codes displayed indicating disrupted functionality
• Soiled dishes from inadequate adjustments meant for heavier loads 

This OEM Bosch part maintains customized cleaning for Thermador versions as well.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

This vent pad cushions and seals the dishwasher's door vent, helping route steam out of the tub while protecting the inner door and control area from moisture. Replacing a worn pad can help stop vent leaks and rattling.

• Creates a seal between the vent assembly and inner door liner to contain moisture
• Helps channel humid air during drying and reduces steam escaping at the vent opening
• Cushions the vent assembly to minimize vibration and noise
• Typical symptoms of a failed pad: steam or water at the top of the door near the vent, moisture inside the console, or a rattling vent

• Disconnect power at the breaker and shut off water before servicing
• Open the door and remove inner-door screws to access the vent assembly
• Note pad placement; install the new pad in the same location with clean, dry mating surfaces
• Reassemble and run a short cycle to check the vent area for leaks

This thermal fuse protects your appliance by opening the circuit if temperatures climb beyond a safe limit, helping prevent wiring or control damage. When it blows, the unit may lose all power or stop mid-cycle. What it does:

• Cuts power when overheating is detected to protect internal components
• Helps prevent damage from shorted heaters, motors, or wiring faults
• Common symptoms: no power, won't start, shuts off during operation, no lights/display
• A blown fuse reads open (no continuity) and must be replaced—it is not resettable

• 1 thermal fuse

• Disconnect power before servicing to avoid electrical shock
• Access the fuse location per your model's service information; note wire orientation and mounting
• Replace one-for-one; do not bypass or up-rate the fuse. Identify and correct the overheating cause before restoring power.

This hose connector joins an appliance hose to its mating port for a secure, leak-resistant connection. Replace a cracked or loose connector to stop drips at the joint and restore reliable flow through the line.

• Provides a secure coupling between a hose and an appliance fitting or another hose
• Helps maintain a tight seal to prevent leaks at the connection point
• Supports proper flow during fill, circulation, or drain operations
• Helps resolve issues such as dripping at the joint, a hose that won't stay attached, visible cracking, or intermittent fill/drain performance

• Disconnect power and, if applicable, shut off the water supply before servicing
• Place towels to catch residual liquid and relieve line pressure
• Transfer and tighten clamps or O-rings per your model; seat hoses fully on the connector
• Run a short test and inspect for leaks before returning the appliance to service

Seal included. This sump housing assembly includes a 32.17 millimeter hole for the thermistor. If the hole for the thermistor is 31-31.5 millimeters you will need to order WP8534882.

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks