Kenmore / Sears Range / Cooktop / Oven Control Board

This electronic controller manages an appliance's user interface and core cycle functions so your unit responds to settings and runs programmed cycles. Replacing a faulty controller restores control responsiveness and cycle management. What it does:

• Receives inputs from buttons/knobs and runs the appliance's cycle logic
• Powers and updates the display and indicator lights
• Regulates timing, relays, and other outputs that start motors, heaters, or valves
• Faulty controller symptoms: unresponsive controls, incorrect or stuck cycles, no display or intermittent power, or visible error codes

• Disconnect power to the appliance before beginning any work to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use a grounded wrist strap if available
• After installing, power up and test functions before fully reassembling the appliance

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Electronic control board that manages an appliance's functions and user commands, restoring proper cycle control, timing, and display responsiveness when replacing a failed or malfunctioning control module. What it does:

• Regulates main appliance functions, timers and cycle sequencing; communicates with sensors, relays and motors.
• Processes user inputs and display signals; helps coordinate start/stop and program selection.
• Common symptoms of a failing board include unresponsive controls, blank or incorrect display, failure to start cycles, intermittent operation, or unexpected error codes.

• Disconnect all power (unplug or shut off circuit) before attempting replacement; hazardous voltage may be present.
• Document wiring and connector locations or take photos before disconnecting to ensure correct reassembly.
• Handle the board by the edges, avoid static discharge, and ensure all connectors and mounting points are secure before restoring power.

This genuine OEM replacement part is a clock timer for ovens. If the display is dim, not visible, and the buttons aren't functioning properly, this could be a sign that the clock timer needs to be replaced. Luckily this is a relatively simple repair. Unplug the oven. The first step is to remove the top panel to gain access to the timer module. Once the top panel is removed, pull the brackets that hold the clock and timer in place. Make sure to take note of the orientation of the wires by taking a picture with a phone camera. Remove the wires and reconnect them to the new clock timer. Snap the timer module back into its original place. Reinstall the top panel and push the oven back in place.This replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse ovens.

The Control Board is an OEM part for Frigidaire ovens. It is an integral electronic component responsible for operating various functions of the oven such as temperature controls, timers, displays, and sensors. The control board works behind the scenes to ensure reliable and consistent cooking performance. 

Causes of a bad control board can include exposure to excess heat over time, damage from electrical surges, or failures in electronic components. 

Symptoms of a bad control board include:

• Lights or displays not working properly 
• Inability to control temperature or time settings
• Unexpected shutdowns or failure to operate as directed
• Error codes appearing on the display

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Installation is recommended by an experienced technician.

This electronic control board manages the appliance's user interface and core operating functions so the unit responds to control input and runs set cycles correctly. Replacing a faulty board restores reliable control and display operation. What it does:

• Interprets user commands from the touchpad/controls and sends signals to motors, valves, heaters, and other components
• Manages cycle timing, settings, and display feedback for normal operation
• Common symptom: control or display is unresponsive, shows error codes, or buttons do not register
• Common symptom: appliance fails to start, stops mid-cycle, or behaves erratically due to lost control signals

• One electronic control board (controller)

• Disconnect power before accessing or replacing the control board to avoid shock risk
• Handle the board by its edges and avoid touching circuit traces or components
• Verify connectors are fully seated and routed clear of moving parts before reapplying power

This is a replacement oven range control board and clock from Frigidaire. It is the heart of the oven and is responsible for managing and monitoring all functions. It allows the user to set the oven temperature, choose baking/broiling cycles, set timers, and more. This part should last for many years, but it can be damaged by prolonged exposure to moisture or high heat.If the control board is failing or has failed, the oven may be inoperable, or it may experience erratic or erroneous operation. A multimeter test is needed to determine if the problem is the control board, though. This part does not include the overlay, which is needed to capture user inputs. To replace the control board and clock, users will need to unplug the oven. Remove the rear access panel of the oven, locate the wiring harnesses, then disconnect them. Remove the mounting screws and then the old board. Install the new board by reversing these steps. This control board is a genuine OEM part and is sold individually. It is compatible with Kenmore ovens.

This electronic clock timer is the oven control module that displays the time and manages timed bake, broil and delay-start functions so your range follows programmed cooking cycles accurately. What it does

• Displays time and lets you set cook timers and delay-start/stop functions.
• Controls timed bake and broil cycles so the oven runs only for the programmed period.
• Can prevent oven from starting when clock/control is malfunctioning (symptoms: blank display, clock won't set, timer won't start).
• Interfaces with the range control console to accept keypad inputs for timed cooking.

• One clock timer (electronic oven control) assembly.

• Disconnect power at the breaker before removing the control console to avoid shock.
• Handle the control and display lens carefully to avoid scratching or damaging the keypad/display.
• Installation typically requires removing the back of the console and unplugging the wire harness; keep screws and mounting hardware.

The Convection Relay Board is an OEM part for Frigidaire ranges. As a specialized electronic component, it seamlessly powers the convection fan and heating elements facilitating enhanced bake modes.

Prolonged electromagnetic interference exposure from convection fan motors degrades functionality over time reducing useful life without replacement. Versatile air circulation cooking depends on consistent control response.

Causes relate to normal electromagnetic component fatigue from field induction multiplying across years of regular convection cooking cycles. Impacts introduce risks abruptly limiting advanced airflow recipes. 

Symptoms indicating relay board issues involve:

• Fan failing to start or run continuously as needed
• Inability to sync convection modes with lower/upper element operation
• Error codes and non-responsiveness during convection preheat 

Replacing with this OEM Frigidaire part restores air movement management. Compatibility also fits some Electrolux, Gibson, and Kenmore ranges.

This main electronic control board manages the appliance's functions and user interface, restoring normal cycle selection and timed operations when the original board fails. Replaces a failed control to return reliable electronic control of the unit. What it does:

• Receives user commands and runs the appliance's operating cycles
• Controls timers, relays and display indicators for proper operation
• Common symptom: appliance won't start or respond to controls
• Common symptom: no or erratic display, or cycles stop unexpectedly
• Helps resolve issues caused by burned or shorted control circuitry

• Disconnect power before attempting any service to avoid shock or damage
• Handle the board by its edges and avoid static discharge; use anti-static precautions
• Verify the appliance model and part number before ordering and swapping parts

This is the main electronic control board that manages user inputs and the appliance's cycle functions, restoring reliable control and display operation when the original board fails. What it does

• Receives and processes button and touchpad commands to run cycles and settings
• Controls timers, relays, and signals to motors, valves, and heaters as applicable
• Helps resolve symptoms like no display, unresponsive controls, or cycles that won't start or advance
• Stabilizes erratic operation caused by a failed or damaged control board

• One electronic control board

• Disconnect power before accessing electrical components to avoid shock or damage
• Replace only with the matching part number; transfer any required connectors or harnesses from the old board

The Control Board with Overlay is an OEM part for Frigidaire wall ovens and ranges. This control board governs all functionality of the oven through electronic programming and user inputs.

Causes of a bad control board can include moisture damage, component failures from power surges or fluctuations over time, and software/firmware issues.

Symptoms of a bad control board include:

• Failures of temperature regulation or heating elements
• Inoperable or unresponsive control knobs and display
• Continuous beeping noises or error codes shown
• The oven failing to begin or complete cooking cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This part is a genuine OEM replacement control board and clock intended for use with ranges.This part contains both the digital display to show the time as well as the buttons for selecting the desired cooking functions and temperature settings. If the user notices the display isn't lighting up or that the settings cannot be selected, it's a sign that this part has gone bad and needs to be replaced. Wear gloves and disconnect the range from power before completing this repair.This part has been made by Frigidaire and has been sourced directly from the manufacturer. It is made out of high-quality, durable, non-corrosive materials to ensure the best possible durability. This control board is sold individually. It is intended for use with ranges manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, and other brands.

This electronic clock timer assembly displays the oven clock and manages timed cooking functions for compatible Frigidaire ranges. It restores visible timekeeping and allows timed bake/clean cycles so the oven follows set schedules. What it does:

• Displays the current clock and lets you set timed cooking cycles
• Starts and stops oven operation based on programmed time settings
• Provides user control for delayed start and automatic shutoff features
• Resolves common symptoms like a blank or non-responsive clock/timer display

• Disconnect power to the appliance before starting any repairs
• Replace through the control panel; some models require removing the oven top or console trim
• Handle the new module carefully to avoid damage to the display and connectors

This main electronic control board regulates the refrigerator's core functions so the unit runs reliably. Replacing a failed control board restores electronic control over cooling, defrost cycles, lights and user interface responses. What it does:

• Manages compressor and fan operation to control temperature
• Runs automatic defrost and associated heater timing
• Powers/display and processes user inputs for settings and diagnostics
• Coordinates dispenser, lights and other electrically controlled features
• Can stop erratic or intermittent operation caused by a faulty control board

• Disconnect power to the appliance before starting work to avoid shock
• Handle the board carefully and avoid touching contacts; use anti-static precautions if available
• Verify connector alignment and secure all wiring harnesses during reassembly