Kenmore / Sears Range / Cooktop / Oven Control Board

Fix a burned-out clock display or unresponsive temperature controls with this oven electronic control board. Restores heating and timer functions.

Range not heating or display blank? The main control board coordinates all cooking functions. This electronic repair requires basic skills and 30-45 minutes.

Oven won't heat to set temperature or display shows error codes? This electronic control board manages bake/broil circuits and clock functions. DIY repair.

This OEM replacement part is an oven control board. The oven control board is the primary computer circuit board that controls the main functions of the oven. These functions include turning the oven on as well as adjusting and maintaining the temperature of the oven. Luckily, replacing a control board is a simple process.To replace the board, first, make sure the oven is unplugged. Gain access to the back of the oven and remove the upper back panel. Once the panel is removed, locate the old control board. Take note of the orientation of the wires by taking a photo with a phone camera. Disconnect the wire harness and any individual wires that are attached to the old board. Re-secure the wires into their correct positions. Snap the new board back in place and reinstall the upper back panel.This genuine replacement control board is compatible with Frigidaire Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

Fix F11 error codes, non-working clock displays, or temperature control issues. This electronic control board restores oven function and display accuracy.

Oven won't heat, wrong element activates, or temperature swings wildly? This control board regulates heating circuits and display. Moderate DIY repair.

Fix an oven that won't heat or respond to controls with this electronic control board. Restores accurate temperature regulation and normal operation.

Fix F10 error codes, runaway oven temps, or ovens that won't heat with this range control board. Moderate DIY repair; disconnect power and remove back panel.

The Noise Filter is an OEM part for Whirlpool built-in wall ovens. It is installed inside the oven cavity near components that produce vibrations, such as the convection fan motor. 

Causes of a faulty noise filter include the degradation of noise-dampening materials over many heating and cooling cycles. Physical damage from accidental impact during cleaning could also compromise its sound-blocking ability.

Symptoms of a bad noise filter include: 

• Excessive buzzing or humming noises emitted from the oven cavity
• Louder than normal fan or component sounds carrying into the kitchen
• Vibrations felt externally on the oven chassis during operation

This OEM replacement fits several Whirlpool, KitchenAid, and Jenn-Air wall oven models.

Oven not heating properly or showing temperature errors? The relay control board sends signals to regulate heating elements. Moderate DIY repair.

Fix unresponsive buttons, error codes, or power surge damage with this range oven control board. Restores all cooking functions and timer operations.

Fixes ovens that shut off during heating or lose temperature over time. Controls heating elements through relay signals. Moderate difficulty repair.

Oven won't heat or display is blank? This electronic control board manages temperature, timers, and element power. Moderate DIY repair in 1-2 hours.

Oven won't bake or broil? This electronic control board manages oven functions and displays. Moderate DIY repair requires console removal.

This electronic oven control board governs your range's heating functions and displays the time and timer. Replacing a failed board restores reliable bake/broil operation, accurate temperature control, and a responsive clock/timer interface. What it does:

• Controls bake/broil circuits to run selected cooking modes
• Monitors the oven temperature sensor and regulates heat to the set temperature
• Drives the time-of-day and countdown timer display
• Interprets keypad inputs for mode selection and settings
• Failure symptoms can include no heat or erratic heat, a blank or flickering display, or unresponsive buttons

• One electronic control board assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use anti-static precautions and handle the board by its edges
• Photograph wiring and transfer connectors one at a time to the same positions
• Reuse the existing mounting hardware and any faceplate/overlay as required; set the clock after restoring power

Fix a dim or blank oven display and unresponsive buttons with a new clock timer control board. Straightforward repair for failed digital displays.