Kenmore / Sears Refrigerator Air Duct Or Vent

The Foam Duct is an OEM replacment part for GE refrigerators. It is an insulating conduit located within the fresh food compartment that helps direct chilled air circulation from evaporator coils throughout interior shelves and bins. The foam duct plays an important temperature regulation role by strategically venting cool air where needed.

Causes can involve cracks in rigid duct walls, compressed insulation, or obstructions within the airflow pathway restricting proper circulation

Symptoms of a defective duct include:

• Inconsistent temperatures with warmer/colder spots within the fridge
• Frost or ice buildup on interior surfaces away from coils
• Higher energy bills from the compressor overworking to maintain temps

Compatible with some Hotpoint, RCA, and some Kenmore models.

This air tower is the vertical duct that channels cold air from the evaporator through the cabinet vents to distribute cooling across shelves. Replacing a cracked or blocked tower restores proper airflow and more consistent temperatures.

• Directs and distributes cold air from the evaporator to the fresh food area
• Helps maintain even temperatures and airflow across the compartment
• Common symptoms of failure: weak/no airflow from vents, warm spots, frost/ice around vent area
• Physical damage such as cracks, broken tabs, or warping can allow leaks and reduce cooling

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/drawers and the rear interior panel to access the tower
• Transfer and reuse existing screws/clips; align tower to seal against vent openings
• After installation, restore power and verify unobstructed airflow from vents

The duct foam assembly insulates and seals the refrigerator's air duct to keep cold air moving efficiently between compartments. Replacing worn or missing foam helps restore airflow control, reduce moisture at the vent, and stabilize temperatures.

• Seals the air duct to prevent warm-air leaks and maintain proper airflow
• Insulates the duct to help keep fresh-food temperatures consistent
• Helps reduce condensation or frost forming around the vent area
• Typical indications include temperature swings, a warm fresh-food section, moisture/frost near the duct, or visibly damaged/missing foam

• Disconnect power to the refrigerator before servicing
• Remove interior shelves/panels as needed to access the air duct; note foam orientation before removal
• Clean the mounting surface; seat new foam fully and evenly to create a complete seal—do not obstruct a damper door or sensor if present
• Restore power and verify airflow and sealing around the vent

This freezer air duct channels cold air from the evaporator fan through the freezer compartment, helping maintain consistent airflow and temperature. Replacing a cracked or missing duct restores a proper seal and reliable circulation. What it does:

• Directs and contains airflow from the evaporator fan within the freezer
• Helps maintain even cooling and reduces warm-air leaks
• A damaged duct may contribute to weak airflow, frost/ice around the vent, temperature swings, or vibration/rattling
• Restores proper alignment and fit with adjoining air tower/panel components

• 1 freezer air duct

• Disconnect power before servicing; wear cut-resistant gloves
• Access is typically from inside the freezer; remove shelves/ice bin and interior air tower or cover as needed
• Save and transfer any screws, clips, gaskets, or insulation from the original part
• Ensure panels and seals seat tightly after installation to prevent air leaks

Bottom air diffuser directs cold air into the refrigerator's lower cabinet to help maintain even temperatures and reduce warm spots. Replacing a damaged diffuser restores proper airflow and helps the fresh-food section cool more consistently. What it does:

• Redirects cold air from the cooling channel into the refrigerator's lower cabinet for balanced cooling.
• Helps reduce warm spots and uneven temperatures in the fresh-food area.
• A cracked, broken, or missing diffuser can lead to restricted airflow and inconsistent cabinet temperatures.
• Seats into the lower air channel and secures with factory tabs or fasteners; inspect mounting tabs for damage.

• Disconnect power to the appliance before performing any service.
• Remove shelves and drawers as needed for access; work carefully around evaporator/air channels.
• Gently release and re-seat plastic tabs or remove fasteners; avoid forcing parts to prevent breakage.
• If tabs are damaged, replace them or consider replacing adjacent vent components to ensure a secure fit.

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed

This refrigerator deflector is a molded guide that mounts inside the unit to direct internal airflow where it's needed. Replacing a cracked, warped, or missing deflector helps restore proper circulation for more consistent temperatures and performance.

• Channels airflow within the freezer/dispenser path to maintain even cooling
• Helps reduce frost or ice buildup caused by misdirected air
• Can address symptoms like warm spots, frost around vents, or rattling from loose parts
• Replace if broken, deformed, or missing

• Disconnect power before servicing
• Remove shelves/panels as needed to access the mounting location; keep track of screws/clips
• Install the new deflector in the same orientation; reuse existing hardware
• Reassemble and verify that vents/air passages are unobstructed

This duct assembly is the insulated airflow duct used inside the dryer to keep exhaust airflow contained and help maintain efficient drying. It replaces damaged or worn insulation to restore proper airflow routing and safety. What it does:

• Channels heated air from the heater to the exhaust while the insulation helps limit heat transfer to the cabinet.
• Prevents airflow leaks that can cause longer dry times or uneven drying.
• Limits heat and noise transfer from the internal duct to the exterior cabinet.
• Replace if the insulation is torn, compressed, or the duct is damaged — common signs include longer drying cycles, unusual heat near the cabinet, or rattling.

• Disconnect power (and shut off gas supply for gas dryers) before starting any repair.
• Access typically requires removing outer panels or the drum; retain all fasteners for reassembly.
• Inspect surrounding ductwork and remove accumulated lint before installing the new assembly.

This duct assembly routes dryer airflow through the appliance's venting system to help remove hot, moist air during cycles. It restores proper airflow routing so the dryer can vent efficiently and dry loads more reliably. What it does:

• Channels exhaust air from the blower to the external vent or internal ductwork
• Helps prevent moisture buildup and reduces drying times when functioning correctly
• Can reduce hot spots and minimize lint accumulation in the cabinet area
• May eliminate abnormal airflow noises caused by damaged or disconnected ducting

• One duct assembly

• Disconnect power (and gas if applicable) before servicing to avoid shock or fire hazard
• Inspect surrounding seals, clamps and mounting points; replace any damaged hardware for a secure fit
• Use basic hand tools; avoid sharp bends or kinks in the duct to maintain airflow

This top air diffuser directs cold airflow inside the refrigerator compartment to help maintain even temperature distribution and reduce hot spots. It replaces a cracked or damaged diffuser to restore proper airflow direction. What it does:

• Channels and disperses cold air from the evaporator into the fresh food cavity
• Helps prevent uneven cooling and localized warm spots
• Replaces broken, cracked, or warped diffusers that cause poor airflow
• Reduces gusty or misdirected airflow noises when damaged

• One top air diffuser

• Disconnect power to the appliance before beginning any repair
• Remove shelves and any interior trim blocking access to the diffuser
• Typically snaps or screws into place; handle gently to avoid cracking

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring proper filling and dispensing when the valve is faulty. It replaces a worn or leaking inlet valve to stop water issues and restore normal operation. What it does:

• Opens and closes to allow water into the icemaker and dispenser as needed
• Prevents water flow when closed to avoid constant filling or overflow
• Commonly linked to symptoms like no water dispensed, no or slow ice production, or intermittent water flow
• Can cause visible leaks if seals or ports fail

• Disconnect power and turn off the water supply before starting any work
• Tighten water line fittings snugly but avoid over-tightening; check for leaks after restoring water

This multi duct directs airflow inside the appliance to maintain proper ventilation and operation. Replacing a damaged duct restores directed air movement and helps prevent exhaust leaks or reduced performance. What it does:

• Routes air between internal components to support heating, cooling, or venting systems
• Prevents exhaust or recirculation air from leaking into the cabinet
• Helps maintain consistent airflow for proper appliance operation
• Can reduce abnormal airflow noise when intact and correctly seated

• Disconnect power (and gas, if applicable) before beginning work
• Handle plastic/metal ducting carefully to avoid cracking or sharp edges
• Verify correct duct orientation and secure all clips or fasteners for an airtight fit

This air tower directs cold air from the evaporator into the fresh-food compartment to help maintain even temperatures and proper circulation. It replaces a cracked, broken or missing tower to restore airflow distribution. What it does:

• Channels cold air from the evaporator into the refrigerator cavity for consistent cooling
• Helps prevent localized warm spots and uneven cooling in the fresh-food section
• Restores proper airflow after impact damage or plastic fatigue
• Works with the evaporator and fan to support overall temperature performance

• Disconnect power to the appliance before beginning any repair
• Typically accessed from inside the refrigerator after removing shelving and the evaporator cover
• Handle near the evaporator coil carefully to avoid damage or refrigerant-line contact
• Use basic hand tools

This water inlet valve controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and ice production when the valve is faulty or worn. What it does:

• Opens and shuts to allow water into the ice maker and dispenser when activated
• Common symptom: no water to dispenser or ice maker
• Common symptom: reduced or intermittent water flow from dispenser
• Common symptom: ice maker not filling or producing smaller/soft ice
• Can cause visible leaks at the valve or connections when failing

• One water inlet valve assembly

• Turn off water supply and unplug appliance before beginning work
• Relieve any pressure in the water line and have towels handy for minor spills
• Verify inlet/outlet hose orientation and tighten all fittings to OEM torque; use replacement gaskets if supplied