Kenmore / Sears Refrigerator Dispenser Parts

Well, I got online and found several YouTube videos on how to check what was happening. I have a multimeter and tools. I first replaced the external water filter just to make sure it wasn't that, and it needed it. That wasn't the problem. I then removed the water inlet valve which was really easy. I didn't disconnect the water lines but I did unplug the power plug. Using the ohms setting on the meter, I tested the coil of the valve solenoid. It wasn't open. I checked the voltage at the plug... Read more

• Door sweating
• Frost buildup
• Ice maker won't dispense ice
• Freezer not defrosting

My refrigerator is 13 yrs old and began to build up frost in the ice cube shoot and the water tube began to freeze up over night. The flapper door was not closing completely. I simply removed the control panel by pulling up and out on the bottom edge, the edge is only about 1/8 inch thick, so don't reach in to far. You should be able to feel a small division line between the control panel and the refrigerator. No screw driver was needed to expose the 4 mounting screws of the inner dispenser... Read more

Unfortunately, this part isn't sold separately, but the plastic that is attached to the metal spring that allows the actuator to disengage broke and I had to physically pull the "paddle" part back up for the water to stop coming out. Easy removal with a square bit screwdriver. First, take off the trim piece underneath the LCD display (screws are underneath), then take out the screws for the LCD display and pull down and out, then unplug the wires. Then take the screws out of the actual part... Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

• Door sweating

The ice dispenser chute door had not been sealing for years. The ice cubes on the lower portion of the ice bin would melt enough eventually to then freeze up into a big, amalgamated blob of ice due to ambient air coming up the chute. This melt-then-freeze would happen, to the extent the chute froze to its own closure. Despite service technician visits over a period of six years nothing they did resolved the issue. I opened the freezer door to reach into the bin from the top to extract usable... Read more

• Not dispensing water

Parts where perfect. piece of cake.my wife was very impressed. Read more

Shopped online and found your great website, read reviews and based diagnostics on similarities I saw in other peoples stories. So I was able to choose correctly when replacing the circuit board. As far as the water switch in door, and drawer parts I just replaced them because I was tired of gluing them, and knew that with everything working good again and looking good, that it would be like a Tune up for our refrigerator. Read more

Unplug refrigerator. Use non marring (plastic trim stick) tool to gently pry loose the plastic assembly containing the PCB display beginning at the lower edge and proceeding around the outer edge. Disconnect all connectors and note the routing of each wire harness and connector (take pictures on cellphone as necessary). Remove two screws holding inner PCB mount bracket in place to expose actuator, flapper door and linkage. Replace actuator (three mounting screws) and ensure that actuator... Read more

Finding the part was puzzling. AppliancePros had the relevant manufacturer's part schematics handy on-line through which I quickly identified and order the replacement part. But the best aspect was AppliancePros' Amazon-like excellence in a) pricing and b) swift delivery (with precious tracking included). Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

Unplug fridge. Use a Phillips head screwdriver to remove the single screw underneath the display. Also under the ledge you will see two slots - one on each side of the forward part of the ledge. Insert a flat-head screw driver and twist (either way) to release the plastic tabs. Once the tabs release you can pull the whole thing loose. Unplug the wiring connector and set the display face aside. Next TAKE A PICTURE OF WHAT YOU SEE WITH YOUR PHONE so you know how everything fits... Read more

I wasn't sure if it was the door being warped, the spring return being worn, or the rotary damper failing, so I ordered all to update the door mechanism. I also ordered a new micro switch since one of the switches had started to require more and more pressure to actuate. Figured I'd fix it at the same time. Repair was very straightforward and the videos available on this and other repair sites were very helpful. I found a video that showed replacing the door mechanism on a nearly identical... Read more

The ice chute flap wasnt closing. 1. I turned off power 2, Pulled off facia around controls on freezer door,, you have to pull out the bottom part of the chute first , its clipped in 3. Disconnected the front panel 4. Unscrewed the next panel to allow access to the chute flap 5. Removed 1 screw holding complete flap and mechanism and replaced with new 6. Re installed all parts in reverse Problem was the chute flap had worn and was folding over on top edge when opened and then wouldnt return... Read more

First, your company web site is extremely helpful. If anyone chooses to do it theirself the ordering process is efficient, quick and easy. Things not found at many companies these days. The last time I ordered from you I got the part in the delivery system within 24 hours, but not so this time. Still I receive this part within 3 days, What I would expect normally when ordering from the internet. I'll never use any other appliance site unless you change for the worse, the customers are the... Read more

So I ordered the face plate and other parts that went with it and fixed it myself. The repair man wanted around $600 to do it. I believe kt cost around $160 to fix it myself. Read more