Kenmore / Sears Refrigerator Bracket & Flange

The Solenoid Valve Kit is an OEM part for GE refrigerators. This kit includes the solenoid valve, which is responsible for regulating the flow of refrigerant in the cooling system.

Causes of a bad solenoid valve kit include electrical malfunctions, physical damage, refrigerant leaks, or general wear and tear over time.

Symptoms of a faulty solenoid valve kit:

• Refrigerator not cooling properly or not maintaining consistent temperatures
• Compressor running constantly or cycling too frequently
• Frost buildup or ice accumulation in the freezer compartment

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models. 

The Lower Hinge Bracket is an OEM part for Frigidaire refrigerators. This bracket supports the refrigerator door, allowing it to pivot smoothly while opening and closing. It ensures that the door remains aligned and operates correctly.

You should replace the lower hinge bracket if it becomes damaged or worn out. Common causes of a bad hinge bracket include wear and tear from frequent use, rust or corrosion, or damage from accidental impacts.

Symptoms of a bad lower hinge bracket include:

• Difficulty in opening or closing the refrigerator door
• The door not aligning properly with the refrigerator body
• Unusual noises when the door is in motion
• Visible damage or rust on the bracket

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Bracket is an OEM part for LG refrigerators. This bracket supports the refrigerator door by providing stability and ensuring proper alignment during opening and closing. It plays a crucial role in maintaining the door’s secure fit, which is essential for maintaining the internal temperature and efficiency of the appliance.

Common causes of a bad door bracket include wear and tear from frequent use, impact damage, or corrosion due to moisture.

Symptoms of a bad door bracket include:

• The refrigerator door not closing properly
• The door sagging or being misaligned
• Unusual noises when opening or closing the door
• Gaps in the door seal leading to temperature inconsistencies

This OEM LG part is also compatible with Sears/Kenmore.

This holder bracket replaces a damaged or missing mounting support. It secures an internal component so it stays aligned and stable, helping your appliance operate smoothly without looseness or rattling.

• Provides a rigid mounting point to hold a component or assembly in place
• Maintains alignment to reduce vibration, rubbing, and intermittent operation
• Restores support when the original bracket is cracked, warped, or missing
• Common symptoms include a loose/wobbly part, rattling noises, or visible broken tabs

• Disconnect power to the appliance before servicing
• Note the original bracket's orientation and transfer any clips or screws from the old part
• Use existing hardware and tighten fasteners evenly—do not overtighten
• Verify proper fit and alignment before restoring power

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

This refrigerator bracket and bushing assembly secures a moving component and provides a stable wear/pivot surface for smooth operation. Replace it when the original parts are worn or broken and causing looseness, scraping noises, or poor alignment.

• Provides a mounting point and bearing surface for rotational or sliding movement
• Helps maintain alignment and smooth, quiet operation
• Can help address wobble, scraping/binding, or a component that sags or sits out of position
• Replace if the bracket is bent/cracked or the bushing is worn/missing

• Disconnect power before servicing; turn off water supply if working near dispenser lines
• Support the attached component while removing fasteners; note the original orientation
• Transfer any spacers/clips from the old parts if present and tighten fasteners evenly
• After installation, verify smooth movement and proper alignment

This lower hinge bracket supports and aligns the refrigerator door at the bottom pivot point. Replacing a bent or worn bracket restores smooth door movement and proper alignment so the door opens and closes without rubbing or sagging.

• Provides the mounting point for the lower hinge/pin at the cabinet base
• Keeps the door square and aligned for smooth opening and closing
• Common fix for door sagging/drooping or rubbing at the bottom corner
• Helps eliminate scraping, binding, or squeaking from a damaged hinge area
• Replaces cracked, bent, or stripped brackets

• Disconnect power and remove items from the door to reduce weight.
• Support the door; remove the bottom hinge cover and screws, then lift the door off the lower hinge pin.
• Remove the old bracket, transfer any reusable hardware/shims, and install the new bracket securely.
• Reinstall the door, check gaps and gasket contact, adjust as needed, and restore power.

This bracket mounts the refrigerator's water filter base/head to the cabinet. Replace a cracked or missing bracket to keep the filter housing secure and properly aligned for smooth filter changes and proper sealing at the connections.

• Secures the water filter head/base to the refrigerator cabinet or liner
• Maintains alignment so the cartridge seats and locks correctly
• Stabilizes the housing to help reduce vibration and drips at the fittings
• Typical symptoms: loose or sagging filter housing, leaks around the filter head, difficulty inserting/removing the filter, rattling during dispensing

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the water filter and any cover or grille to access the bracket
• Support the filter head and tubing; remove mounting screws and swap in the new bracket using existing hardware
• Restore water and power, reinsert the filter, then check for leaks and flush per your filter's instructions

This pivot block kit provides the pivot support that keeps the appliance door or assembly aligned and moving smoothly. Replacing a worn block restores proper door movement and reduces sagging, rubbing, or uneven operation. What it does:

• Provides a dedicated pivot point that supports and guides the door/assembly during opening and closing
• Restores proper alignment to prevent door sag, dragging, or uneven gaps
• Reduces noise and sticking associated with worn or broken pivot components
• Works with the factory hinge and mounting hardware to maintain original movement

• Disconnect power (and water/gas if applicable) before any service or repairs
• Inspect surrounding hinge hardware and mounting points for related wear; replace as needed

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

This bracket is the factory support used to mount a component securely inside your appliance. Replacing a damaged bracket restores proper alignment and reduces vibration, keeping the part stable so it operates as designed. What it does:

• Provides a rigid mounting point for the designated component
• Maintains correct alignment to help prevent rubbing, rattling, or noise
• Replaces a cracked, bent, or missing bracket to restore secure fit
• Typical signs include vibration, a loose or misaligned part, or visible damage

• 1 bracket

• Disconnect power before servicing
• Wear cut-resistant gloves; cabinet edges can be sharp
• Reuse original screws/fasteners and any spacers or grommets from the old bracket
• Mount in the original position and tighten fasteners evenly without overtightening

This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.

• Secures the solenoid to its housing or frame to prevent shifting
• Maintains proper alignment for reliable actuation
• A worn or broken saddle can cause buzzing/chattering and intermittent operation
• Restores stable mounting to help the connected mechanism work correctly

• Disconnect power; shut off water supply if working near water lines
• Access the solenoid assembly and note the original saddle's orientation
• Transfer the solenoid into the new saddle and reuse existing fasteners/clips
• Smooth operation before reassembling panels

This lower hinge bracket mounts at the bottom of the cabinet to support and align the refrigerator door. Replacing a bent or worn bracket helps restore smooth door operation and a consistent gasket seal to help reduce air leaks.

• Provides the mounting base for the lower hinge/pin at the bottom of the cabinet
• Supports the door's weight to keep it level and properly aligned
• Helps the door open and close smoothly without scraping or binding
• Typical symptoms: door sagging or misalignment, difficulty closing, gaps at the gasket, squeaks/scraping near the lower hinge, or visible bracket damage

• Disconnect power; remove items from the door and support the door to prevent dropping
• Mark hinge/bracket locations for alignment; remove bottom hinge cover and mounting screws
• Transfer hinge pin and any spacers from the old bracket if applicable; install the new bracket and tighten screws securely
• Rehang and align the door; confirm full gasket contact and smooth door swing

Right side mount

Motor Bracket secures the motor assembly, keeping it aligned and reducing vibration for reliable operation. Replacing a damaged bracket restores stable motor mounting and helps reduce noise and premature motor wear. What it does:

• Secures and supports the motor to maintain correct alignment and stable operation.
• Reduces motor vibration and operational noise when properly installed.
• A cracked, bent, or broken bracket can cause increased noise, vibration, or motor misalignment.
• Use when the existing bracket is bent, damaged, or failing to hold the motor securely.

• Disconnect power to the appliance before starting any repair.
• Access may require removing the cabinet or an access panel; keep track of fasteners.
• Installation typically requires basic hand tools; avoid forcing parts into position.

Left side mount