Kenmore / Sears Refrigerator Lever Parts

The Water Actuator is an OEM part for Frigidaire refrigerators. It is a crucial component of the dispenser system, primarily responsible for initiating the water dispensing process when pressed. This actuator typically sits behind the water dispenser lever on the refrigerator door, acting as the mechanical link that triggers the water flow when activated by the user.

Symptoms of a faulty water actuator include:

• Inability to dispense water when the lever is pressed.
• Intermittent or inconsistent water flow.
• Unusual noises during actuation.

Causes of a bad water actuator can include mechanical wear and tear, failure of the spring mechanism that returns the lever to its original position, or electrical issues that prevent the actuator from functioning properly. Regular usage and accidental impacts can also lead to the deterioration of this part.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Dispenser Actuator is an OEM part for Frigidaire refrigerators. It is responsible for activating the water dispenser when you press a glass or container against it, allowing water to flow from the dispenser.

You should replace this water dispenser actuator if it stops functioning properly. Causes of a bad actuator can include wear and tear from frequent use, damage from excessive force or impact, or electrical faults within the actuator mechanism.

Symptoms of a bad water dispenser actuator include:

• Water not dispensing when the actuator is pressed
• The actuator sticking or not returning to its original position
• Unusual noises when attempting to dispense water
• Water dispensing intermittently or uncontrollably

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice and Water Dispenser Pads is an OEM replacement part for Whirlpool refrigerators. It consists of two actuator pads that attach directly to the dispenser housing and are responsible for activating both the water and ice dispensers. The pads work together to trigger the dispensing mechanism and intuitively control the flow of water and release of ice cubes.

Constant use can cause actuator pads to become worn out or damaged.

Symptoms of bad pads include:

• Intermittent or unreliable dispensing
• Increased difficulty activating the dispensers
• Dispensers activating on their own without input

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Ice Dispenser Actuator is an OEM replacement part specific to Frigidaire refrigerators. It is the electronic component responsible for actuating and operating the ice and water dispenser. 

Symptoms of a bad ice dispenser actuator include:

• The ice or water dispenser not working or dispensing intermittently  
• No signal or responsiveness from the dispenser button
• Ice cubes were dispensed incorrectly in large clumps instead of individually

Causes of failure can be related to wear and tear of moving parts over time, failures in the small electronic circuit board, or damage to wiring affecting power delivery to the actuator motor. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This refrigerator dispenser actuator is the paddle/lever you press with your glass to start ice or water dispensing. Replacing a cracked or worn actuator restores smooth operation and consistent switch engagement at the door dispenser.

• Engages the dispenser micro switch to initiate ice or water dispensing
• Provides the user-facing paddle/lever in the dispenser recess
• Helps the dispenser return to its rest position after you release
• Common symptoms: no dispense when pressed, intermittent response, broken/loose paddle, sticking or continuous dispense if jammed

• Unplug the refrigerator and shut off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access the actuator; protect the finish and avoid breaking locking tabs
• Note spring and pivot orientation; transfer any reusable hardware to the new actuator
• Reassemble, restore power/water, and test both ice and water dispensing

This hinge lever mounts on the refrigerator door hinge to guide door movement and closure, helping the door seal properly. Replacing a worn or broken lever restores smooth operation and consistent sealing.

• Guides hinge motion so the door opens and closes smoothly
• Helps maintain door alignment for a reliable gasket seal
• Replace if the lever is visibly cracked, worn, or deformed

• Disconnect power and support the door to prevent injury or damage
• Remove the hinge cover and fasteners; note the lever's orientation before removal
• Install the new lever in the same position and reassemble the hinge components
• Adjust hinge per model procedures if needed

This dispenser crank links the dispenser solenoid and the ice chute door. When you press the dispenser lever, the crank pivots to open and close the ice door so cubes or crushed ice can dispense cleanly without warm air leaking into the freezer.

• Connects the solenoid to the ice chute door to control door movement
• Helps seal the chute when not dispensing to reduce frost and moisture issues
• Common failure signs include ice door not opening/closing, constant frost around chute, or warm/moist air leakage at dispenser
• Can cause ice clumping, frost buildup, or water/ice dispensed irregularly when worn or broken

• Disconnect power before servicing the dispenser area
• Access typically requires removing the dispenser front panel and trim; use care with plastic tabs and wiring
• Note linkage orientation to the solenoid and door flap before removal
• Inspect related parts for wear while open

This humidity control is the adjustable slider in the crisper drawer cover that opens and closes the vent to regulate moisture around fruits and vegetables. Replace a cracked or missing control to restore smooth adjustment and consistent crisper conditions.

• Mounts to the crisper cover and links to the vent/damper door
• Slides between settings to increase or reduce airflow for proper crisper humidity
• Typical symptoms: broken or missing lever, slider stuck or loose, vent doesn't move as you adjust, excess condensation or wilting produce

• Disconnect power; remove food, crisper pan, and cover/glass as needed—handle glass carefully
• Release the old control from its slot/retainer and note the vent linkage orientation
• Seat the new control and engage the linkage; confirm full travel and proper vent action
• Reassemble the cover and drawer, then restore power

This damper actuator controls the air damper that directs cold air between compartments, helping maintain consistent temperatures. Replacing a worn actuator restores regulated airflow and reduces uneven cooling or temperature swings. What it does:

• Moves the air/damper door to open or close the airflow path between freezer and fresh-food sections.
• Helps balance compartment temperatures by adjusting how much cold air is shared.
• A failing actuator can cause uneven cooling, temperature fluctuations, or reduced cold air in the fresh-food compartment.
• May make clicking noises or show no damper movement when faulty.

• Disconnect power to the appliance before starting any service.
• Access typically requires removing the damper housing or control cover in the fresh-food compartment.
• Align the actuator shaft with the damper linkage, seat the gear, and reconnect the electrical connector — do not force parts.

This actuator replaces the ice dispenser door motor that opens and closes the dispenser door so ice can drop into your cup. Restores proper door movement to help prevent ice blockages and missed dispenses. What it does:

• Drives the dispenser door to open and close when the dispenser is activated.
• Allows ice to release into the cup while keeping the dispenser sealed when idle.
• Common symptoms: dispenser door won't open, ice not dispensing, clicking or humming from the door area.
• Replaces a failed or intermittent dispenser door motor to restore normal dispensing action.

• Disconnect power to the appliance before beginning any repair.
• Replacement typically requires removing the inner dispenser/door panel; use common hand tools and keep track of fasteners.
• Inspect door linkage and wiring harness for damage when replacing the actuator.

The Lever Dispenser is an OEM part for LG refrigerators. It is the control mechanism responsible for dispensing crushed ice and water through the refrigerator door without opening it. The lever and dispensing components are designed to withstand frequent use while retaining smooth, reliable operation. 

Causes of a bad lever dispenser can include worn parts inhibiting proper dispensing movement, cracks or damage reducing structural integrity, or mineral buildup affecting functionality over time.

Symptoms of a bad lever dispenser include:

• Difficulty or inability to dispense ice and water
• Leaks or drips around the dispenser area 
• Loose, rattling, or unresponsive lever action  
• The dispenser not activating or emptying the reservoir

This OEM LG part is also compatible with dispenser models featured on Kenmore side-by-side refrigerators.

This dispenser lever is the replacement actuator that presses the ice/water switch so your refrigerator dispenses on demand. Restores proper contact and smooth push action for reliable dispensing. What it does

• Acts as the user-facing lever you press to activate the ice or water dispenser
• Re-establishes firm, consistent contact with the dispenser switch when the original lever is cracked, loose, or broken
• Stops intermittent dispensing caused by a worn or misaligned actuator
• Matches the OEM shape for correct alignment and smooth operation

• Turn off power to the refrigerator or unplug it before starting work
• Most installations are screw- or snap-style; remove the dispenser bezel to access the lever
• Handle plastic components gently to avoid cracking; use trim tools if needed

This replacement water-dispensing lever restores a refrigerator's push-activated water control so you can dispense water easily and reliably. Fits the dispenser paddle area and matches the appliance's white finish. What it does:

• Replaces a broken or cracked dispenser lever so the water paddle can be pressed comfortably
• Transfers user pressure to the internal water valve or actuator to start water flow
• Helps stop intermittent leaks caused by a damaged or misaligned lever
• Restores proper feel and alignment for consistent dispensing

• One water dispenser lever (white)

• Inspect the dispenser area and valve linkage before installing
• Typically secures with a snap-fit or a small screw; handle gently to avoid cracking plastic
• Disconnect power at the appliance and shut off the water supply before service for safety

This actuator kit controls the refrigerator air damper to regulate airflow between compartments, helping maintain steady temperatures and proper cooling. It restores damper movement so the appliance can direct cold air where needed. What it does:

• Rotates or opens/closes the air damper to control airflow between freezer and fresh-food compartments
• Restores damper movement when the damper is stuck, noisy, or unresponsive
• Helps correct temperature imbalance or uneven cooling that can result from a faulty damper actuator
• Stops clicking or grinding noises caused by worn actuator gears or motor

• Always disconnect power to the appliance before beginning repair to avoid shock or injury
• Handle the actuator and plastic gears gently; do not force the damper shaft or gears during installation
• Reconnect electrical connectors fully and verify actuator orientation so the damper opens/closes correctly

This genuine dispenser arm replaces a worn or broken dispenser actuator to restore proper soap or rinse aid release during cycles. It helps ensure the dispenser opens and delivers product at the correct time for normal wash performance. What it does:

• Replaces the dispenser actuator that moves to release detergent or rinse aid during a cycle
• Helps correct symptoms such as the dispenser not opening, soap not dispensing, or detergent tabs staying trapped
• Works as the mechanical link between the dispenser door and the release mechanism
• Engages with the dispenser assembly so product is delivered at the proper time in the cycle

• Disconnect power before servicing to avoid electrical shock
• Basic hand tools required; follow OEM instructions for proper alignment and reassembly
• Inspect related dispenser components (door, latch, springs) for wear and replace if needed

Color: Apollo Grey