Kenmore / Sears Wall Oven Hinge Parts

This oven door hinge supports and guides the door through its range of motion so it opens smoothly and seals tightly when closed. Replacing a fatigued hinge restores proper door alignment and consistent oven performance. What it does:

• Provides spring-assisted tension to control door opening and closing
• Helps the door seal evenly against the gasket to retain heat
• Maintains correct stop positions to prevent slamming or over-travel
• Common symptoms: door won't close fully or pops open, drops/slams, sits crooked, heat escaping/long preheat

• One door hinge assembly

• Disconnect power at the breaker; allow the oven to cool completely before servicing.
• Remove the door per your model's procedure (often open to the broil stop, engage hinge locks, then lift off).
• Use hinge locks/pins to control spring tension and prevent snap-back during removal/installation.
• Support the door to avoid damage; many replace both hinges together to keep tension balanced.

This door hinge kit restores smooth, controlled movement and proper alignment of the appliance door when the original hinge is worn, bent, or binding. Replace a faulty hinge to help the door open and close correctly and sit flush.

• Controls the door's pivot and closing action for smooth operation
• Maintains alignment so the door sits flush and latches reliably
• Replaces a bent, loose, or fatigued hinge that causes rubbing or sagging
• Helps resolve symptoms like squeaking, binding, or a door that won't stay closed

• Disconnect power before servicing; allow the appliance to cool completely.
• Support the door during removal; hinges can be under spring tension—use caution and wear gloves/eye protection.
• Note hinge orientation and mounting hole locations; transfer any brackets/screws from the original hinge.
• After installation, check door alignment and operation; adjust if your model provides slotted mounts.

The Range Hinge is an OEM part for Frigidaire ranges. It is a hinge component that is responsible for securely and smoothly attaching the range door to the cabinet. The hinge allows for easy opening and closing of the oven door while cooking. 

Causes of a bad hinge can include wear and tear over time, excessive force or weight placed on the door, or damage from impacts. 

Symptoms of a bad hinge include:

• The door not closing or opening fully  
• The door becoming loose or detached from the cabinet
• Noises or squeaking when operating the door
• Difficulty or resistance when opening or closing 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hinge kit restores a refrigerator door's secure attachment so the door opens, closes and seals properly. Install to correct sagging, misalignment or noisy pivot points and help maintain consistent cabinet closure. What it does:

• Secures the appliance door to the cabinet and provides the pivot point for smooth movement
• Restores proper door alignment to help improve sealing and reduce air gaps
• Replaces worn or bent hinge hardware that can cause door sagging or rubbing
• Reduces creaks, binding or uneven door movement when operating the door

• Disconnect power to the appliance and remove food from the door before starting
• Support the door during removal and installation to prevent drops or damage
• Tighten hardware securely but avoid over-torquing; verify door alignment and seal after installation
• Follow OEM instructions for your model before ordering

This replacement door hinge restores smooth, secure opening and closing for a refrigerator door. It replaces a worn or damaged hinge to help stop sagging, rubbing, or uneven gaps around the door. What it does:

• Supports the refrigerator door and maintains proper alignment
• Allows the door to pivot smoothly without sticking or binding
• Helps maintain a consistent door seal to prevent cold air leaks
• Commonly used when the door sags, scrapes the cabinet, or won't close fully

• Disconnect power to the appliance and remove food from the door area before starting
• Support the door while removing and installing the hinge to prevent damage or injury
• Typical installation requires basic hand tools (screwdriver, wrench); hardware may need loosening/tightening for alignment

Left hand side. For right hand use WB14K5006