Kenmore / Sears Washer Dryer Combo Parts

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement timer knob mounts to the control timer shaft, allowing you to select cycles and settings with a positive, secure feel. Replacing a cracked or stripped knob restores smooth, accurate control of the timer.

• Attaches to the timer shaft so you can rotate and set the desired cycle
• Restores function when the original knob is cracked, loose, or stripped
• Helps resolve issues like the knob spinning freely, wobbling, or falling off
• Provides firm, reliable engagement for precise timer adjustments

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; retain and transfer any inner spring clip if present
• Align the new knob with the flat side or splines of the shaft and press on until fully seated
• Support the control panel during removal/installation and avoid excessive force

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This replacement heater assembly restores proper heat output in your appliance. It delivers the thermal energy needed for normal operation so your unit can reach and maintain the correct temperature and complete cycles as designed.

• Generates heat for the appliance's heating/drying/defrost function (as applicable to your model)
• Helps the unit reach and maintain target temperature for proper performance
• Common failure signs: no heat or weak heat; cycles take too long or do not complete
• May trigger heating-related error/fault codes; visible breaks or hot spots on the element; tripped breaker from a short to ground

• Disconnect electrical power before servicing; allow hot components to cool
• Wear cut-resistant gloves; internal panels and chassis edges can be sharp
• Document wire routing and mounting positions before removal; route wiring exactly as original
• After installation, ensure secure connections and clearance from metal surfaces; run a brief test cycle to verify operation

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This hinge secures the door to the cabinet and provides a smooth pivot. Replacing a bent or worn hinge restores proper alignment and reliable latching so the door opens easily and closes securely.

• Provides the pivot point for the door to open and close
• Supports door weight and keeps it aligned with the latch/strike
• Wear or damage can cause sagging, rubbing, or squeaking
• A misaligned door may not engage the door switch, preventing the cycle from starting

• Disconnect power before servicing; shut off gas supply
• Support the door before removing mounting screws to avoid strain or damage
• Note hinge orientation; transfer any spacers/shims and reuse existing hardware
• Align the hinge, snug screws, then tighten fully and test door operation

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

This replacement flexible hose transports water between appliance components to restore proper flow and prevent leaks. It's a direct-fit service part used when the original hose is cracked, split, or leaking. What it does

• Carries water between the pump, tub, valve or drain—depending on model configuration
• Replaces damaged or brittle hose sections that cause visible leaks or puddling
• Restores proper draining when kinks or collapses impede flow
• Helps stop intermittent drips or steady leaks that occur during operation

• One flexible replacement hose

• Disconnect power and shut off the water supply before starting work
• Inspect and replace hose clamps or connectors if corroded or damaged
• Route and secure the hose to avoid kinks, pinching, or contact with sharp edges
• Test the appliance through a full cycle after installation and check all connections for leaks

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

This retaining ring secures a shaft or component in-place to prevent axial movement and wear, restoring proper alignment and reducing noise or wobble. It's a small, durable replacement part for assemblies that use a snap-style ring. What it does:

• Holds shafts, bearings or components axially in their mating grooves to prevent shifting.
• Stops rattling, grinding, or excessive play caused by a worn or missing ring.
• Keeps assemblies aligned to reduce premature wear on surrounding parts.
• Provides a simple replacement solution when the original ring is bent, broken, or lost.

• Disconnect power and/or water and remove any panels needed before starting work.
• Use snap-ring pliers or the manufacturer-recommended tool to safely remove and install the ring.
• Inspect grooves and mating surfaces for damage or debris and clean before installing the new ring.
• Wear eye protection and keep fingers clear—snap rings can spring out during removal or installation.

This strike screw secures the door strike/catch to the appliance, keeping the latch aligned so the door closes firmly and any safety interlock engages. Replacing a missing, stripped, or corroded screw helps restore reliable, consistent door latching. What it does:

• Fastens the strike/catch to the door or cabinet
• Maintains proper alignment for positive latch engagement
• Helps address issues like door not latching, loose/rattling door, or intermittent door switch activation
• Replace if threads are stripped, the head is damaged, or the screw is missing

• 1 strike screw

• Disconnect power before servicing; allow hot surfaces to cool. For gas appliances, also shut off the gas supply.
• Support the door or strike and remove the damaged/missing fastener.
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening.
• Verify door alignment and latch/lock operation after installation.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test