Kitchenaid Refrigerator Bracket & Flange

This bracket mounts the refrigerator's water filter base/head to the cabinet. Replace a cracked or missing bracket to keep the filter housing secure and properly aligned for smooth filter changes and proper sealing at the connections.

• Secures the water filter head/base to the refrigerator cabinet or liner
• Maintains alignment so the cartridge seats and locks correctly
• Stabilizes the housing to help reduce vibration and drips at the fittings
• Typical symptoms: loose or sagging filter housing, leaks around the filter head, difficulty inserting/removing the filter, rattling during dispensing

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the water filter and any cover or grille to access the bracket
• Support the filter head and tubing; remove mounting screws and swap in the new bracket using existing hardware
• Restore water and power, reinsert the filter, then check for leaks and flush per your filter's instructions

Replacement mounting bracket that secures a panel or internal assembly to the appliance so parts stay aligned and stable. Installs in minutes to stop rattling, reduce movement and restore a proper fit. What it does:

• Provides a secure mounting point for a panel, trim or internal component
• Keeps assemblies aligned to prevent gaps, rubbing or binding
• Stops rattling and vibration caused by a loose or damaged bracket
• Replaces bent, cracked or corroded brackets that no longer hold parts firmly

• Disconnect power (and water if applicable) before beginning any repair
• Retain original fasteners; replace damaged screws or clips as needed
• Hand-tighten fasteners first, then torque to manufacturer specs if available

Right side mount

Left side mount

This mounting bracket secures internal components in place to keep your appliance stable and operating quietly. It replaces a worn, bent, or broken bracket to restore proper alignment and prevent loose or rattling parts. What it does:

• Provides a stable mounting point for panels, assemblies, or hardware
• Keeps connected components aligned to prevent rubbing or vibration
• Stops noises caused by loose or shifting internal parts
• Restores proper fit when an old bracket is bent, cracked, or missing

• Install with appliance unplugged or power disconnected to avoid shock
• Verify bracket orientation using the appliance's service diagram before fastening
• Use appropriate screws/fasteners and torque to avoid stripping or distortion

This retainer secures the dryer fan motor to its housing so the blower assembly stays aligned and runs quietly. Replacing a worn retainer restores proper motor mounting and reduces vibration or rubbing noise. What it does:

• Holds the fan motor in place to maintain correct blower alignment
• Prevents the motor or fan from shifting, which can cause noise or rubbing
• Helps avoid airflow loss that can lead to poor drying performance
• Reduces vibration that can stress mounts and fasteners

• One fan motor retainer

• Disconnect power before starting any repair to avoid shock or injury
• Basic hand tools are usually required; retain original fasteners unless replacements are provided
• Inspect surrounding mounts and the blower wheel for damage while accessing the motor

This right-side basket cradle secures and supports a dishwasher rack so it rolls and nests correctly. It replaces worn or broken cradles to restore smooth rack movement and stable loading in the dishwasher. What it does:

• Holds the right side of the upper/lower basket in place and guides rack travel
• Restores proper alignment when racks tilt, wobble, or catch during sliding
• Helps prevent rack detachment or uneven loading caused by a broken cradle
• Works with the existing rack hardware and rollers to maintain normal operation

• Designed for straightforward replacement; remove the rack to access the cradle
• Inspect adjacent rollers and clips while replacing; replace any damaged hardware
• Use basic hand tools; disconnect power only if working near electrical components
• Dispose of damaged pieces and package new part per local regulations

This bracket is a factory-design mounting support that secures internal components in place for stable operation and alignment. It helps keep parts seated correctly to reduce noise and prevent component movement. What it does:

• Provides structural support for internal assemblies and panels
• Holds components in correct alignment to maintain proper operation
• Helps reduce rattling or vibration caused by loose parts
• Compatible where the OEM bracket W10174827 is specified

• Disconnect power to the appliance before starting any repair
• Use the correct fasteners and torque as specified by the manufacturer
• Wear safety gloves and eye protection to avoid cuts on sharp edges

This mounting bracket secures internal components to the appliance chassis to keep parts aligned and reduce movement during operation. It restores stable support so attached parts function reliably and quietly. What it does:

• Secures a component or assembly to the appliance frame to prevent shifting or sagging
• Maintains proper alignment of parts for reliable operation
• Helps reduce vibration and noise caused by loose or unsupported components
• Worn or broken brackets can cause rattling, misalignment, or intermittent part failures

• One mounting bracket

• Disconnect power before servicing to avoid electrical shock
• Use appropriate hand tools; keep fasteners for reinstallation unless new ones are specified
• Inspect surrounding components and mounting hardware; replace any stripped or damaged screws

This adapter connects the appliance's water line to the inlet fitting, providing a secure path for water flow to components like ice makers and dispensers. It helps restore proper water delivery and prevents loose or leaking connections. What it does:

• Creates a sealed connection between the supply line and the appliance inlet
• Restores proper water flow when a worn or damaged connection causes low or no water delivery
• Stops leaks caused by cracked or loose fittings at the inlet
• Works where a direct hose-to-inlet connection needs a small matching adapter

• One adapter as shown

• Disconnect power and shut off the water supply before starting any work
• Verify correct orientation and thread engagement; hand-start threads then snug with a wrench—do not overtighten
• Inspect nearby hoses, seals, and fittings; replace if cracked or damaged

The ice maker bracket is an OEM part for Whirlpool refrigerators. This bracket is a structural component that holds and supports the icemaker assembly within the refrigerator. It allows for secure mounting and installation of the icemaker while also maintaining proper alignment.

Causes of a bad bracket can include wear and tear over time, cracks or breaks due to impact or stress, or corrosion issues that compromise the integrity of the mounting structure.

Symptoms of a bad bracket include:

• Loose or unstable icemaker installation
• Improper ice production or dispensing
• Noise or vibrations emanating from the icemaker area
• Moisture leaks or water damage near the bracket mounting points

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This mounting bracket secures internal panels and components to restore proper alignment and support. It replaces a worn or broken bracket to reduce rattling and keep parts correctly positioned for safe operation. What it does:

• Provides a stable attachment point for panels or assemblies
• Stops movement that can cause rattling, noise, or misalignment
• Restores proper fit between connected parts after damage or wear
• Helps prevent strain on adjacent components that can lead to failure

• High-level replacement: remove nearby panels or fasteners to access and swap the bracket
• Use correct fasteners and torque; replace any damaged clips or screws
• Disconnect power before working on electrical appliances and follow safety procedures