Kitchenaid Wall Oven Parts

This surface element supplies heat to an electric range or cooktop burner. When it fails, the burner may not heat or may heat inconsistently. Replacing the element restores steady, reliable cooking performance.

• Converts electrical energy into heat for the cooking zone
• Works with the surface control (infinite switch) to regulate temperature
• Common symptoms: burner won't heat, intermittent or uneven heating, visible breaks/blistering, burnt/melted terminals
• A failed element will not glow or reach set temperature when energized

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• If your model uses a plug-in coil style: remove the drip pan, pull the element straight out of the receptacle, and inspect/replace a heat-damaged receptacle as needed
• If your model uses an under-glass radiant style: lift the cooktop, transfer any clips/limiters from the old element, and route wires exactly as original
• After reassembly, test the burner at a low setting to ensure proper operation

Color: Black. Instruction sheet included.

The Knob Bezel is an OEM Replacement Part designed for Whirlpool cooktops. This part is located behind the burner knob and serves the crucial role of labeling different burner settings. 

Causes of a bad bezel-knob can include regular wear and tear, accidental impacts, or exposure to heat and cleaning chemicals. Over time, the bezel may crack, discolor, or become loose.

Symptoms of a bad bezel-knob include:

• Cracks or breaks in the bezel
• The bezel becoming loose or falling off
• Discoloration or fading
• Difficulty in turning the control knobs due to misalignment

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This infinite surface element switch controls the heat output of a cooktop/range element. Replacing a worn switch restores smooth, reliable temperature adjustment for the designated Flex element, preventing issues like stuck-on-high heat, no heat, or erratic cycling.

• Regulates power to the surface element by cycling on and off at the selected setting
• Dedicated control for the unit's Flex element circuit
• Common failure symptoms: element won't heat, only heats on high, won't shut off, or heats inconsistently

• Disconnect power at the breaker before servicing to avoid electrical shock
• Pull the control knob straight off; access the switch from the control panel and note its orientation
• Label and transfer wires one at a time to matching terminals on the new switch
• Reassemble, restore power, and test all heat settings for proper operation

For Stainless Models.

This burner cap sits on top of the surface burner head to shape the flame and shield the head from spills. Replacing a damaged or missing cap helps restore even heating, reliable ignition, and the cooktop's original appearance.

• Covers the burner head and disperses flame for more even cooking
• Protects burner head and ports from food and liquid spills
• Helps maintain proper ignition and a steady blue flame
• Helps with symptoms like uneven/yellow flame, delayed ignition, or poor simmer

• Allow the cooktop to cool completely before handling
• Disconnect power and shut off gas
• Clean the burner head and clear ports before seating the cap
• Center the cap so it sits level and flush; misalignment can affect ignition and flame

This Frame-Glass is the outer glass panel for the oven door, restoring a clean appearance and helping retain heat while keeping the oven cavity visible. It replaces damaged, cracked, or chipped outer door glass. What it does:

• Provides the outer glass surface of the oven door for safe viewing of food while cooking
• Helps maintain oven heat and improve energy containment when the door is intact
• Replaces cracked, chipped, or shattered outer door glass that can affect appearance and safety
• Restores a sealed, clean-facing surface for the door assembly

• Disconnect power to the appliance and allow the oven to fully cool before beginning
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires removing the oven door and detaching trim/fasteners; keep track of screws and clips

Black

This surface burner head distributes gas to create an even, consistent flame on your range's cooktop. Replacing a damaged or clogged head restores reliable ignition and proper heat on the affected burner. What it does:

• Directs the gas/air mix through flame ports for an even flame pattern
• Works with the spark igniter and burner cap to light the burner
• Helps ensure steady simmering and full burner output
• Worn, corroded, or clogged heads can cause weak, uneven, yellow, or no flame

• 1 surface burner head

• Disconnect power and shut off gas; allow the cooktop to cool
• Remove grate and burner cap, then lift off or unfasten the old head
• Position the new head over the orifice and igniter; secure with the original hardware
• Reinstall the cap and grate, restore gas/power, and verify ignition and flame pattern

The Burner Grate is an OEM part for Whirlpool ranges and cooktops. This grate sits atop of gas or burners, providing an even heat distribution surface for cooking pots and pans.

Causes of a bad burner grate can include warping or melting from exposure to excessive heat, damage from scratches or impact, or corrosion over time.

Symptoms of a bad burner grate include:

• Uneven or inefficient heat transfer to cookware
• Hot spots or cool spots on the cooking surface
• Damage, warping or breakage of the grate material

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This oven door gasket restores a tight seal between the door and oven cavity so your appliance can hold set temperatures. Replacing a worn seal helps reduce heat loss for more consistent preheating and baking results.

• Seals the gap between the oven door and frame to keep heat and moisture inside
• Helps maintain accurate oven temperatures and reduce energy loss
• Replace if the gasket is torn, hardened, flattened, frayed, or falling out of its channel
• Common symptoms: heat escaping around the door, long preheat, uneven baking, odors or smoke leaking from the oven

• Disconnect power and allow the oven to cool completely before servicing
• Gently pull the old gasket from the channel or unhook its retainers; note clip locations/orientation
• Press the new gasket evenly into the groove without stretching; align any corner pins/clips to match the original
• Close the door and check for uniform contact around the seal

This transient suppressor protects the appliance's electronic control by absorbing power-line spikes and electrical transients. Replacing a failed suppressor helps restore stable control operation and helps protect sensitive components from surge-related damage.

• Clamps voltage transients on the AC line to shield the control and related electronics
• Helps reduce interference that can cause erratic displays or unexpected resets
• Failure may leave the control dead, cause intermittent operation, or trip the household breaker
• Often shows visible heat damage, cracking, or discoloration when defective

• Disconnect power at the breaker and verify no voltage is present before servicing
• Access the control compartment; the suppressor is typically located near the electronic control or power input
• Photograph wiring and transfer one lead at a time to ensure correct connections and snug terminals
• Inspect and replace any heat-damaged wires or terminals before reassembly and test

This griddle creates a flat, continuous cooking surface that rests on your range or cooktop grates. It adds versatile space for items like pancakes and sandwiches, and replaces a worn or missing original griddle to restore safe use. What it does:

• Provides a broad, flat surface across burners for griddle-style cooking
• Direct replacement for a damaged, warped, or missing griddle
• Useful for foods that need a continuous surface (pancakes, eggs, grilled sandwiches)
• Common reasons to replace: wobbling/poor fit on grates, cracks, or persistent sticking from wear

• 1 griddle

• Turn all burners off and let the cooktop cool before placing or removing the griddle
• Position per your model's instructions so it sits flat and secure on the grates
• Preheat gradually on low to medium heat; handle only with oven mitts
• Allow the griddle to cool completely before cleaning or moving

Replacement control knob for select Whirlpool appliances that restores safe, reliable operation of the control shaft. Replace a cracked, stripped or missing knob so you can accurately select cycles, temperatures or functions. What it does:

• Snaps onto the control shaft to let you turn and set appliance functions or temperature settings.
• Replaces knobs that are cracked, melted, stripped, loose or missing and no longer provide positive engagement.
• Restores the indicator pointer so you can clearly see the selected setting.
• Compatible with matching splined control shafts.

• Always disconnect power (unplug or shut off breaker) before servicing controls.
• Pull the old knob straight off the shaft; align the replacement's indicator with the shaft flat/spline and push on firmly until seated.
• If the knob won't seat or turns loosely, inspect the control shaft for damage—replace the switch or shaft assembly if needed.

The Regulator is an OEM replacement part for Whirlpool ranges. It is responsible for controlling the flow of gas to the burners and ensuring the proper gas pressure for efficient and safe cooking.

A bad pressure regulator can occur due to wear and tear, clogs, or damage to the internal components. If you notice symptoms such as weak or inconsistent flame, gas leaks, or difficulty in igniting the burners, it may indicate a faulty valve and pressure regulator.

Symptoms of a bad regulator include:

• Weak or inconsistent flame
• Gas leaks
• Difficulty in igniting the burners

Restore your range by replacing the faulty or damaged valve and pressure regulator with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Blower Motor is an OEM part for Whirlpool ranges. It is an electronic component located underneath the range that is responsible for removing heat, smoke, and odors from the kitchen. The down draft blower motor operates an exhaust system that draws air through a vent behind the cooking surface and vents it outside.

Causes of a bad down draft blower motor can include normal wear and tear over time, exposure to grease or debris which can cause clogs or mechanical issues.

Symptoms of a faulty down draft blower motor include:

• Inadequate ventilation of heat, smoke or odors from cooking
• Slow or delayed venting of the cooking area
• Loud buzzing or grinding noises coming from underneath the range
• Failure of the venting system to turn on

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.