Parts for Ge PT925DN2BB: 03 - Lower Oven Parts

Secures the capacitor inside your oven. Replace if the bracket is bent, broken, or missing to properly mount and protect the electrical capacitor component.

Fix F9 error codes and overheating control panels with this cooling fan motor. Restores airflow to protect internal components. Moderate DIY repair.

Small rubber bumper that cushions contact between oven door and cabinet. Replace if cracked, missing, or worn to reduce noise and protect finishes.

Oven won't heat or shuts off during use? This high limit switch cuts power when temperatures exceed safe levels. Moderate DIY repair for wall ovens.

This rack guide and nut assembly keeps a dishwasher rack aligned and sliding smoothly on its tracks, restoring stable rack movement and preventing the rack from catching or coming off the rail. Simple replacement for worn or broken guides. What it does:

• Repositions and supports the lower (or upper) rack so it slides straight on the track
• Prevents the rack from binding, sticking, or derailing during cycles
• Replaces broken, cracked, or missing guide pieces that allow lateral movement
• Reduces scraping, clanking, and uneven rack travel caused by damaged guides

• Disconnect power to the appliance or turn off the circuit before beginning work
• Remove the affected rack and slide off the old guide to access mounting fastener(s)
• Reinstall new guide in the same orientation; secure nut/fastener snugly but avoid over-tightening
• Test rack movement after installation to ensure smooth operation

Offset oven rack that slides into side rails to hold cookware at specific heights. Replace if bent, warped, discolored, or damaged from heavy use or impacts.

Standard oven rack for wall ovens. Installs on side supports to hold cookware during baking and roasting. Replace if bent, warped, or damaged.

Seals the back lamp assembly in your wall oven to prevent heat loss and moisture intrusion. Replace if cracked, brittle, or no longer sealing properly.

If your wall oven won't heat properly or takes too long to preheat, the lower bake element may be burned out. This repair restores even heating.

Fix F2 error codes and inaccurate oven temperatures by replacing a faulty temperature sensor. Simple 15-minute DIY repair with basic tools.

Retainer bolt secures internal components and panels in your range or wall oven. Replace if bolt is stripped, missing, or causing loose assemblies.

Replace your oven's halogen bulb when the interior light burns out or dims. Illuminates the oven cavity so you can monitor cooking without opening the door.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

This rail support secures an oven rack guide so the rack slides smoothly and stays aligned. It restores proper rack movement and prevents sagging or binding for safer, more reliable oven use. What it does

• Holds and aligns the oven rack guide so racks slide in and out smoothly
• Replaces a cracked, broken, or worn support that causes rack wobble or misalignment
• Prevents racks from tipping or catching when pulled forward
• Works with the oven's rack system to maintain stable cooking and loading

• One rail support

• Disconnect power to the appliance before starting any repair
• Typically accessed from the oven interior; remove racks to reach the support
• Install with basic hand tools; do not force parts into place—ensure correct orientation

Replaces the lower exterior trim on your wall oven door. Restores a secure fit and clean appearance where original trim is cracked, bent, or missing.

The Probe Thermistor is an OEM replacement part for GE wall ovens and ranges. Located inside the oven cavity, this temperature-sensitive probe precisely monitors interior heat to safeguard against overcooking.

Causes of a faulty thermistor involve exposure to excessive cooking temperatures, moisture infiltration from spills or steam, or basic failure due to old age.

Symptoms of an inadequate probe thermistor include:

• Inaccurate temperature readings and baking inconsistencies
• Oven temperature exceeding desired setting risking fire

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This panel conceals and protects internal freezer components while providing a finished interior appearance. Located inside the freezer compartment, replace it when cracked, warped, or allowing moisture and cold air to reach sensitive mechanical parts.

This compressor start relay helps the refrigerator compressor receive the initial jolt it needs to start running, restoring normal cooling when a worn relay prevents compressor startup. It's a direct-fit replacement specified by the manufacturer. What it does:

• Provides the momentary boost the compressor needs to start under load
• Helps prevent repeated hard-start attempts that can overheat or damage the compressor
• Commonly used when a refrigerator hums but the compressor won't start
• Works with the compressor's start device circuitry to control start winding engagement

• One replacement compressor start relay

• Disconnect power to the appliance before servicing to avoid shock
• Access and replace the relay per the appliance's service instructions; avoid bending terminals
• Inspect the compressor and wiring for additional damage before reassembly

The Wall Oven Capacitor Motor is an OEM part for GE wall ovens. Located inside the oven cavity, this motor is responsible for turning the convection fan which circulates hot air for even baking and roasting. 

Symptoms of a bad capacitor motor include:

• Inability to select convection bake or roast features 
• Uneven cooking results 
• Lack of air circulation inside the oven
• Strange noises coming from the fan/motor area
• The convection fan not turning on 

Causes of failure can be wear over time, damage from debris inside the oven, or occasional voltage fluctuations which can degrade motor components.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Wire harness for oven temperature probe. Connects probe sensor to control board. Replace if wires are frayed, connectors are damaged, or harness is broken.

Replacement mounting screw for refrigerators. Secures brackets, panels, handles, and covers. Replace lost, stripped, or damaged screws to restore stability.

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

Replacement mounting screw for securing panels, brackets, and components inside your appliance. Needed when original screws are stripped or missing.

These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.

This part fixes the following symptoms:

• Loose or wobbly parts or panels within the appliance's interior or exterior
• Panels or components falling out of place, creating gaps or exposing internal parts
• Unusual noises or rattling sounds during the appliance's operation

The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

ST10-16 X 7/16"

Black-finished screw secures oven panels, trim, and brackets. Replace missing or damaged fasteners to restore solid fit and prevent rattling or gaps.

Replacement screw for securing panels, brackets, and internal components in ranges, ovens, and cooktops. Replace missing, stripped, or damaged screws.

Black. 8-18 AB HXW 3/8

Replace your missing, worn, or damaged range washer. This small metal component secures parts and assemblies throughout your oven, ensuring proper fit.

Replacement washer for ranges and ovens. Used to secure components and provide even fastening. Replace if cracked, worn, or missing during repairs.

Ribbon connector assembly that links control boards to user interface components. Needed when the existing flat flex cable is damaged, torn, or worn.

Wire harness connecting relay board to sensor in wall ovens. Replace if wires are frayed, connectors damaged, or harness is melted or broken.

Wire harness assembly connecting sail switch and temperature probe in wall ovens. Replace if wires are frayed, connectors damaged, or harness is worn.

10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.