Need Help?
Call or text
Burner won't heat or heats unevenly? This 8-inch coil surface element restores reliable cooking power to your range. Simple plug-in installation.
It's one of the easiest jobs in the world. It take longer to unwrap the parts than to install them. Looks great...works great. Easy, Done. Read more
This terminal block provides an insulated, secure junction for incoming power or harness leads inside the appliance. Replacing a cracked, loose, or heat-damaged block restores a safe, reliable connection and helps prevent arcing or intermittent power.
I completely disassembled the entire unit sandblasted repainted with epoxy paint and reassembled. bought a few new parts and its like new again this unit is no longer available and its built into my boat. Read more
This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.
I REPLACED THE HINGE ASSY ONLY BECAUSE I WAS UNABLE TO PURCHASE THE SPRING ONLY. THIS IS 3rd TIME I REPLACED THE HINGES BECAUSE OF A BROKEN SPRING. IT WOULD BE CHEAPER IF ONLY THE SPRING COULD BE BOUGHT. Read more
Replace a broken or fatigued oven door spring to restore proper counterbalance. Installs behind side panel. Ensures door closes firmly and seals correctly.
It was a simple fix. I removed the six screws holding the side panel on the range. Removed the broken parks of the spring. I use a screwdriver to help stretch the new spring into place. I then replaced the side panel and screwed it on. About ten minutes work. Read more
Burner not heating or heating intermittently? This 8-inch surface element restores your cooktop. Easy DIY repair—just unplug the old, plug in the new.
I ordered new elements and connection blocks, ripped out the old ones and installed the new ones. The ordered parts came in quickly and were exactly what I ordered. The most difficult part of the repair was cutting through the little screws that had rusted and corroded over the decades. With old removed, the installation of the new blocks and elements went quickly. One modification was to the support fins on the new heating elements. The element did not seat nicely most likely because the... Read more
Oven won't turn off or stays on low heat? This temperature-sensing thermostat regulates oven heat and prevents overheating. Moderate DIY repair.
I replaced the thermostat and its control switch as it was not able to turn off. Read more
Color: black. Measures about 2 inches in diameter.
Replaced burner tubes and installed a new nob on the sparker control. Read more
This contact spade is a push-on electrical terminal used to connect an appliance wire lead to a component's blade. Replacing a worn or heat-damaged connector restores a secure fit and consistent power flow.
Full disassembly of removable tray into top plate (stainless) and lower pan taking care not to loose fasteners. Removal of terminal blocks using lubrication on rusted screws and, if necessary, drill out technique. Unclip wires from edges of the tray on both sides without losing the clips for future re-use. Top plate is now completely free of connections and may be cleaned/scrubbed separately in advance of re-assembly. Unfasten spade insulation block (located in the front of the tray) after... Read more
Adjustable front leveling leg threads into the base corner of your range to raise or lower the unit. Replace if broken, cracked, or missing to level your range.
Replaced Read more
Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.
First check to see how many leads your switch has before ordering - I ordered before I took things apart, and got an incorrect 2 lead version when I needed a 3. On starting the repair, at first thought I might have to take apart console - but happily, no. After turning off power, just carefully pried the old switch out (putty knife to depress plastic clips above & below), pulled out gently (not much slack on wires) and removed the old wires by gently easing them off the broken switch with a... Read more
Oven won't heat or overheats? This thermostat monitors temperature and controls heating elements. Moderate DIY repair requires back panel removal.
Removed back panel and top burner cover to replace thermostat Read more
Washer won't start or spin? A broken lid switch actuator prevents the safety switch from engaging. This plastic striker restores proper operation in 5 minutes.
Replace the broken switch Read more
Color: Almond. This kit includes ( 2 ) 6 inch pans and ( 2 ) 8 inch pans
Not really a repair, just needed to update some parts that were worn out. Drip pans were perfect and I am so glad to have found them on this location. Read more
This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:
I replaced the downdraft fan and fan motor of my 25 year old JennAire C301 cooktop. The issue was getting the fan/motor assembly out in such a tight place. I had to first remove the fan cover, cut the wires, then the assembly came out. Putting back wasn't as tough although getting the cover back on (over the motor) was a bit of a strain. Wired it back, turned it on, and was thrilled. Now I'll replace the knobs and burners and we're back in business. Read more
Burner not heating or heating unevenly? This 8-inch surface element kit restores even heating on your electric range. Simple plug-in install in 15 minutes.
I got online to research what the problem could be and came to realize the infinite switch had probably shorted out when the element broke. While looking for the part I came across an appliancepartspro video that showed me exactly how to replace the switch. I ordered the switch from applicancepartspros.com, which arrived in two days! I watched the video again while installing the part and had it done in less than 30 minutes. The hardest part was lining up the end caps as I put the stove... Read more
Pilot burner assembly with thermocouple for gas range ovens. Replace if pilot won't stay lit, flame is weak, or assembly is cracked or corroded.
I replaced the pilot burner, this was a fairly easy job! best to remove the unit from its enclosure, then its just unhook and reinstall. Took about 20 minutes. Read more