Magic Chef Dishwasher Parts

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

This black timer knob replaces a worn, cracked, or missing control knob so you can easily set the oven or range timer. Restores a positive grip and clear pointer for accurate timer adjustments. What it does:

• Fits onto the timer/control shaft to allow manual setting of the cook/timer function
• Replaces broken or stripped knobs that spin or won't engage the control
• Provides a visible pointer for precise timing and repeatable settings
• Improves user grip and control when turning the timer dial

• One black timer knob

• Power off the appliance before servicing electrical controls
• Pull the old knob straight off the shaft; align and push the new knob onto the splined shaft until fully seated
• Do not force the knob onto the shaft; verify correct spline alignment to avoid damage
• If the knob does not seat or the control shaft is damaged, inspect the control assembly and replace as needed

This motor-pump assembly replaces the washer's drain pump to restore reliable water removal and reduce leaks. It mounts to the tub and handles draining so your cycle can finish and clothes can spin out properly. What it does:

• Pumps water out of the washer during drain cycles to allow proper spin and cycle completion
• Helps prevent standing water and reduces the chance of overflow or tub leaks
• Stops humming, grinding, or no-drain symptoms caused by a failed pump motor
• Works as the integrated motor and pump unit that attaches to the washer tub

• Disconnect power and water before servicing; follow all safety precautions
• Basic hand tools required; access may require removing front or rear service panel
• Inspect and reinstall hoses and clamps securely to prevent leaks

This roller fits the cable bracket assembly and helps guide the cable smoothly to reduce binding and wear. It restores proper cable tracking so the mechanism moves more quietly and reliably. What it does:

• Guides and supports the cable within the bracket so the cable runs true
• Reduces rubbing, binding, and premature cable wear
• Helps eliminate squeaks or grinding where the cable contacts the bracket
• Restores smoother operation of the affected door/assembly movement

• One roller for the cable bracket (quantity: 1)

• Disconnect power before starting any repair and follow all safety guidelines
• Requires basic hand tools; access the bracket per your model's service instructions
• Inspect the cable and bracket for wear or damage and replace if necessary
• Test operation after installation to ensure proper cable routing and smooth movement

Color: White. Size: 13 oz. Spray paint primer. can.

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

This collector hose assembly routes and channels water inside the appliance to the drain area, helping maintain proper water flow during cycles. It replaces worn, cracked, or leaking collector hoses to reduce leaks and maintain performance. What it does:

• Channels wastewater from internal tub components to the drain system
• Helps prevent leaks caused by cracked, split, or brittle hose sections
• Restores proper routing when the original hose is kinked, collapsed, or damaged
• Compatible with factory routing and mounting points for correct fit

• Disconnect power and water supply before starting any repair
• Inspect adjoining clamps and fittings; replace if corroded or damaged
• Follow OEM routing and secure with the original clamps or new OEM-style clamps

Note: For faucet adapter

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements