Magic Chef Range / Cooktop / Oven Parts

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Little to no heat when broiling

Ordered a new part. Watched a YouTube video. Fixed it in 15 minutes. Knowing you need to stop the connectors from slipping into the back of the oven was the key. I used paperclips to stop the wires falling through the hole. Easy as ... Read more

Ordered new drip pans from Appliance Parts Pros, hoping they'd fit perfectly...and THEY DID! We are so happy with them. The ones at other places didn't. Read more

• Element will not heat

1. Went online where I watched video about heat control for this Maytag. I then found AppliancePartsPros using Google. I ordered the part and In three days the part arrived. I installed the part and now the problem has been corrected. Read more

• Little to no heat when baking
• Oven not heating evenly
• Oven is too hot
• Won't start

I'm a 66 year old woman (on a fixed income) and I'd never before repaired an oven bake element . My stove is 20 years old but I still found it was much more affordable to change the bake element rather than buying a new stove. I called the number on the website and talked to a very informative woman. She answered all the questions I had about my stove. She told me about the repair video on the website which had step-by-step instructions. I ordered a new element - received it within 4 days.... Read more

• Won't start

Replaced srark module Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

Replaced switch with back cover off and power plug pulled. The replacement switch was the same as old, was easy to pull off wires and push on new one. Also replaced torn door gasket with new one and was a exact replacement both only took less than a hour. Read more

• Element will not heat

Followed the instructions that came with the replacement part: made sure stove top was unpowered, unscrewed the old housing from the stove top, cut the wires, stripped some insulation off, attached the new wires with the (accompanying) wire nuts, attached new housing to stove top. Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replaced It With New One Read more

• Door won't close

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more