Maytag Cooktop Knob, Dial & Button

Color: black. Measures about 2 inches in diameter.

Replace a worn or missing surface-burner knob with this black infinite switch control knob. It restores smooth, accurate heat selection on your range or cooktop when the original knob is cracked, stripped, loose, or missing. What it does:

• Interfaces with the surface burner's infinite switch to select OFF through Low–High heat levels
• Restores positive, secure control of the burner
• Typical symptoms: knob cracked, spins freely, falls off, or can't adjust temperature
• Helps ensure consistent response when turning the burner on/off and setting heat

• Disconnect power and allow the cooking surface to cool completely
• Pull the old knob straight off the switch shaft
• Align the new knob with the shaft and press on until fully seated; do not force
• Rotate through all settings to confirm smooth operation

The Range Clock Knob is an OEM part for Whirlpool ranges. It attaches to the center of the oven control panel and allows users to adjust the built-in clock, serving as the primary control for setting or correcting the time. 

Over time, the clock knob can become faulty due to regular use leading to internal stripping or wear, exposure to heat causing cracks or warping, or accidental impacts damaging the knob.

Color: Black

Symptoms of a defective range clock knob include:

• Difficulty setting or adjusting the clock
• The knob spins freely without engaging the control shaft
• The knob feels loose, cracked, or broken

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore ranges.

This thermostat knob fits onto the control shaft so you can select and adjust cooking temperature. Replace a cracked or stripped knob to restore smooth operation and a clean, finished look.

• Attaches to the thermostat stem to allow manual temperature selection
• Replaces knobs that are cracked, stripped, loose, or missing
• Helps when the knob spins without engaging or won't stay on the shaft
• Restores proper control feel and appearance

• Disconnect power to the appliance and allow surfaces to cool before service
• Pull the old knob straight off the thermostat shaft
• Align the new knob with the shaft and press straight on until fully seated; do not force
• The pointer aligns with the control markings before use

Color: stainless steel. Measures about 2 inches in diameter.

Black surface burner control knob for gas ranges and cooktops. It fits onto the valve stem so you can turn the burner on/off and fine-tune flame level, restoring proper control and appearance when the original is worn or missing.

• Attaches to the surface burner valve shaft to control on/off and flame level
• Replaces knobs that are cracked, stripped, loose, hard to turn, or missing
• Restores clear pointer alignment for accurate settings
• Helps when the knob spins without engaging the valve

• Turn all controls OFF, allow the cooktop to cool, and disconnect power to disable igniters
• Pull the old knob straight off the stem; align the new knob opening with the stem and press straight on until fully seated
• Verify the pointer aligns with the OFF marking before use
• Do not force the knob or use tools—forcing can damage the valve stem

This thermostat control knob replaces a worn or broken temperature selector knob. It restores a clean look and positive feel so you can reliably set cooking temperatures. White finish matches the original appearance. What it does:

• Attaches to the thermostat shaft to select temperature settings
• Replaces knobs that are cracked, stripped, loose, missing, or hard to read
• Restores smooth turning and a secure fit on the control stem
• Helps ensure the pointer aligns with the temperature markings

• One white thermostat control knob

• Turn all controls off and allow the appliance to cool before service; disconnect power if accessing any internal panels
• Pull the old knob straight off the thermostat shaft; avoid prying on the panel
• Align the new knob's hub with the shaft and press straight on until fully seated
• Verify pointer alignment with the temperature scale and re-orient if needed

This is a surface burner control knob for electric cooktops. It replaces a worn or broken knob so you can accurately turn the burner switch to the desired heat setting and restore a matched look on the cooktop.

• Attaches to the surface burner (infinite) switch shaft to set heat level
• Helps when a knob is cracked, stripped, loose, hard to turn, or missing
• Restores positive engagement and clear pointer alignment for temperature selection

• Disconnect power before servicing
• Pull the old knob straight off the switch shaft; align flat/"D" shape and press the new knob on
• If the knob does not seat, inspect the switch stem for damage or mismatch
• Test each position for smooth rotation and proper detent feel before use

Replace a damaged or missing selector knob to restore smooth, precise control of your appliance settings. This knob fits onto the selector switch shaft so you can easily turn and choose functions as intended.

• Attaches to the selector switch shaft to turn and select functions/settings
• Replaces a cracked, stripped, wobbly, or missing knob
• Helps when the knob slips or won't stay on the shaft
• Restores proper alignment with panel markings for accurate selections

• Disconnect power and allow the appliance to cool before servicing
• Pull the old knob straight off; if tight, gently wiggle while pulling
• Align the new knob with the keyed/flat on the switch shaft and press fully into place
• Verify smooth operation and correct pointer alignment with panel markings

Replace a worn, cracked, or missing surface burner knob to restore smooth, precise heat control on your cooktop. This direct-fit knob brings back easy ON/OFF operation and clear setting alignment for everyday cooking.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame or heat level
• Common symptoms: knob cracked or stripped, spins freely or falls off, melted/discolored, or missing
• Restores proper pointer alignment and a clean, finished look
• Designed for the surface burner position; match style and shaft orientation to your original

• Allow the appliance to cool completely before servicing
• Pull the old knob straight off the valve stem; do not pry against the control panel
• Align the stem orientation with the new knob and press straight on until fully seated
• Disconnect power or shut off gas before any work near controls

Replacement control knob for the oven thermostat. It installs on the thermostat shaft so you can select cooking temperatures. Replaces a cracked, loose, or missing knob to restore smooth adjustment and clear, readable settings. What it does:

• Provides the hand control to turn the oven's thermostat and set temperature
• Press-fits onto the thermostat shaft for consistent, aligned operation
• Restores a secure grip and pointer alignment when the original is worn
• Common symptoms: knob cracked, falls off, spins freely, or markings are hard to read

• One white thermostat control knob

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Pull the old knob straight off the thermostat shaft—avoid prying against the panel
• Align the new knob with the shaft flat and press straight on until fully seated
• The pointer aligns with Off; remove and reseat if needed

This surface burner knob fits the valve stem for a cooktop/range burner control. It restores a secure grip and accurate adjustment when the original knob is cracked, stripped, loose, or missing.

• Attaches to the surface burner valve stem to turn the burner on/off and adjust flame level
• Replaces a knob that slips, won't stay on, cracks, melts, or free-spins
• Helps restore proper Off alignment and a clean, finished look

• Ensure all controls are in the Off position; disconnect power and shut off gas as a safety precaution
• Pull the old knob straight off the valve stem—do not pry sideways
• Align the flat/D-shaped opening with the valve stem and press firmly until fully seated
• Verify smooth operation and correct Off alignment before restoring power/gas

Color: Black. For biscuit use WP8522567. For white use WP8522565.

Color: Black. It measures about 2 inches in diameter.

This white switch knob replaces a damaged or missing control knob, restoring a clean look and smooth, confident operation when selecting settings. It press-fits onto the control shaft so you can adjust functions without wobble or slip.

• Attaches to the control switch shaft to turn and select settings
• Replace if the knob is cracked, stripped, loose/wobbly, or missing
• Common symptoms: knob falls off, won't engage the switch, or is hard to turn
• Normal wear, heat, or impact can damage the original knob over time

• Disconnect power and ensure the appliance is cool before servicing
• Pull the old knob straight off the shaft; avoid prying against the panel or switch stem
• Align the new knob with the shaft and press straight on until fully seated
• Verify alignment with the OFF position and test operation

Color: black. It measures about 2 inches in diameter.