Maytag Cooktop Parts

Burner won't heat or stays on high? This dual radiant surface element restores proper heating. DIY-friendly repair—lift cooktop, disconnect wires.

This is a control knob for a range surface burner, used to adjust the flame or heat level on the cooktop. It attaches to the burner valve stem on the front control panel. Replace this knob if it is cracked, broken, melted, or if the D-shaped shaft opening is worn out and the knob spins freely without engaging the valve.

If your burner won't ignite, won't shut off, or the knob feels loose, the top burner valve likely needs replacement. Moderate DIY repair in 1-2 hours.

Removable metal panel forming the floor of your oven cavity. Replaces cracked, warped, or rusted bottom panels to protect heating elements and restore a clean baking surface.

Replace your worn, cracked, or missing cooktop control knob. Attaches to the control shaft for smooth turning and positive grip when adjusting settings.

Color: Black. Used on some dryers and broiler drawers.

Fix burners that won't light with this cooktop igniter switch wire assembly. Restores reliable spark ignition when switches fail. Moderate DIY repair.

This is a spark electrode igniter used on a gas range surface burner. It generates an electric spark to ignite the gas when the burner knob is turned. Replace this part if the burner clicks but does not light, produces a weak or inconsistent spark, or if the ceramic insulator is cracked.

Black control knob for electric range surface burners. Replaces cracked, stripped, loose, or missing infinite switch knobs. Restores heat selection.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

Range not broiling or browning food evenly? A failed broil element is the likely cause. This radiant heating coil restores strong, even heat for searing.

Burner won't light or flame won't adjust? This gas surface burner valve controls fuel flow to restore ignition and smooth flame control on your cooktop.

Oven won't heat or maintain temperature? A failed bake element causes uneven cooking and long preheat times. This lower heating element restores consistent heat.

Black surface burner control knob for gas ranges and cooktops. It fits onto the valve stem so you can turn the burner on/off and fine-tune flame level, restoring proper control and appearance when the original is worn or missing.

• Attaches to the surface burner valve shaft to control on/off and flame level
• Replaces knobs that are cracked, stripped, loose, hard to turn, or missing
• Restores clear pointer alignment for accurate settings
• Helps when the knob spins without engaging the valve

• Turn all controls OFF, allow the cooktop to cool, and disconnect power to disable igniters
• Pull the old knob straight off the stem; align the new knob opening with the stem and press straight on until fully seated
• Verify the pointer aligns with the OFF marking before use
• Do not force the knob or use tools—forcing can damage the valve stem

Gas pressure regulator for cooktops and ranges. Mounts to the gas supply line and controls gas flow to burners. Replace if cracked or leaking.

This orifice spud meters gas to the burner for a consistent, correctly sized flame. Replace a clogged or damaged spud to restore proper burner output and reliable ignition on your gas cooktop or range.

• Controls and meters gas flow through a calibrated opening to the burner
• Helps ensure proper flame size and color when matched to the correct burner and fuel type
• Common symptoms of a failing or clogged spud: weak or uneven flame, yellow tipping, or delayed ignition
• Damaged threads or a stripped orifice can prevent correct sealing and fuel delivery

• Shut off gas supply and disconnect power; allow the appliance to cool
• Access the orifice holder/manifold for the affected burner; remove the old spud with an appropriate orifice wrench or nut driver
• Start the new spud by hand to avoid cross-threading; tighten snugly—do not overtighten brass threads
• Restore gas and check for leaks with an approved leak-detection solution; verify flame quality and adjust per the service manual