Maytag Range Switch

This main wire harness routes power and control signals between the appliance's control board and components to restore electrical connectivity and reliable operation. Replacing a damaged harness helps eliminate intermittent faults and lost functions. What it does:

• Provides the primary electrical connections between the control board and motors, switches, sensors and valves
• Carries power and signal wiring so controls and components operate as intended
• Commonly replaces harnesses with broken, melted, or corroded wires or connectors
• Can resolve symptoms such as no power to components, intermittent operation, or unresponsive controls

• Disconnect power to the appliance before inspecting or replacing the harness
• Compare connector types and routing to the original harness; install in the same path to avoid chafing
• Secure connectors fully until they click; avoid pulling on individual wires
• If wiring or connectors show heat damage or corrosion beyond the harness, inspect associated components.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

For switch mounting nut, order part# WP422617.

This burner switch controls the power and heat settings for a surface cooking element, restoring reliable on/off operation, accurate temperature selection, and consistent element cycling on compatible electric ranges. What it does

• Regulates electrical power to a surface burner so the element heats to selected settings and cycles to maintain temperature.
• Replaces a worn or failed switch that causes a burner to not heat, not respond to knob changes, or only work on certain settings.
• Stops intermittent operation or arcing at the switch caused by worn contacts.
• Helps resolve a burner that stays on or will not turn on when the switch is faulty.

• Always disconnect power at the breaker before starting any repair to avoid shock.
• Photograph and/or label wires before removal so you can reconnect terminals correctly.
• Handle terminals gently and ensure secure, tight connections; replace any damaged wiring or connectors.
• Test the range on all heat settings after installation; if you see arcing, burning smell, or continued malfunction, cut power.

This infinite switch controls the variable heat settings for a cooktop surface burner, restoring adjustable heating for smooth cooking. It replaces a failed control to help the burner reach and hold selected temperature levels. What it does

• Regulates power to a surface element so heat changes smoothly from low to high.
• Common symptom: burner won't heat or only works on one setting.
• Common symptom: heat level won't change or is stuck at a single setting.
• Can cause clicking or intermittent burner operation when failing.

• Disconnect power to the appliance at the breaker before servicing.
• Confirm terminal locations and wiring match your original switch; label wires before disconnecting.
• Access typically requires removing the cooktop or control panel.

This burner ignitor switch controls spark delivery to a cooktop burner so the burner lights when the knob is turned. It replaces a worn or failed switch to restore ignition responsiveness and consistent sparking. What it does:

• Routes spark current to the surface burner ignitor when the control knob is turned
• Stops spark delivery when the control knob is released or turned off
• Commonly used when a burner fails to spark or sparks intermittently
• Works with the cooktop's ignition system to enable safe, reliable lighting

• One burner ignitor switch

• Disconnect power (and gas if applicable) before servicing to avoid shock or injury
• Access may require removing the cooktop or control panel
• Verify wiring and switch operation with a multimeter before replacement

Replacement burner switch that controls the heat level for an electric range surface element, restoring proper temperature selection and burner responsiveness. Use this switch when a burner is unresponsive, stuck at one setting, or heats erratically. What it does:

• Regulates power to a surface element so you can select low-to-high heat settings.
• Replaces a failed surface control switch that prevents burners from changing temperature.
• Common symptoms it can fix: burner won't heat, stuck on one setting, no click/response, or inconsistent heat.
• Works as the control interface between the knob and the element on compatible electric ranges.

• Disconnect power at the breaker or unplug the range before starting any repair.
• Photograph or label wires before removal and match terminals exactly when installing the replacement.
• Use insulated tools and avoid contact with live terminals; restore power only after reassembly.

This ignition switch controls spark to a gas range burner so burners light reliably when a knob is turned. Replaces a worn or failed switch to restore normal ignition and consistent burner operation. What it does:

• Sends the electrical spark signal to the burner igniter when the control knob is turned
• Allows the range to ignite burners; a failed switch can prevent sparks and burner ignition
• Works with the range's safety/ignition system to enable proper start-up sequencing
• Helps eliminate intermittent sparking or no-spark symptoms linked to a faulty switch

• Disconnect power and turn off the gas supply before beginning service
• Basic hand tools required; access may require removing the cooktop or control panel
• Handle electrical connections carefully and restore grounding; follow manufacturer instructions

This genuine replacement wire harness connects and routes power and signal lines between appliance components, restoring reliable electrical communication for normal operation and control response. What it does:

• Replaces damaged or frayed wiring that can interrupt power or signals
• Restores reliable connections between controls, motors, and sensors
• Helps resolve intermittent operation, loss of certain functions, or failure to start when caused by wiring faults
• Provides factory-style connectors and routing for secure, vibration-resistant connections

• Disconnect power to the appliance before starting any repairs
• Handle connectors carefully; match connector shapes and colors to the original
• Route the harness as the OEM diagram specifies and secure with clips or ties to prevent chafing

This igniter switch assembly replaces a worn or failed switch that controls ignition to a gas burner or oven igniter, restoring reliable spark/ignition and consistent burner operation. What it does

• Acts as the electrical switch that signals the igniter or spark module to light a burner or oven
• Helps resolve intermittent or no-spark ignition symptoms and burners that fail to light
• Restores proper on/off switching for the ignition circuit when the original switch is damaged or worn
• Works as the direct replacement switch component in the ignition system

• One igniter switch assembly

• Disconnect power and shut off gas supply before starting any repair
• Use basic hand tools; handle wiring connectors carefully to avoid damage
• Verify part compatibility with your model before installation