Maytag Wall Oven Parts

I knew for sure that the hinge with the large spring was damaged, but elected to replace both hinges and receivers. Replacing the parts was fairly easy and would have taken me less then an hour. This model has thin metal covers over the hinge assemblies. I found that squeezing in the sides of the covers help to hold them in place on the hinge while reassembling the door. My only difficulty was putting the door back on the oven. It took a little maneuvering but I managed to get it. Now the door... Read more

Installed the new pans and replaced the coils. My Jennaire looks like new. Only took minutes and made such a difference. Read more

Of course, before disassembling anything, I unplugged and turned off the gas supply. To replace the spark electrode, I removed the drip pan/surface to gain access to the burner assemblies. Next, I unscrewed (with a 1/2" open-end wrench, I think) and disconnected the gas supply tubing from the burner assembly with the cracked electrode, and then unscrewed the assembly itself from the base surface. With the assembly detached, I flipped it over and removed the screw that secured the cracked... Read more

You have to take the knob off the broken part, then buy the new switch element and fix it. To do this you turn the power off, take out 6 fasteners to release the front panel of the stove and replace the switch element. Then put it all back together. Very simple. But if the knob was designed better it would not have broken in the first place. It looks nice, but this is the third time I have had to fix one. Read more

Replaced fuse. It took much longer to get the oven out of the wall to access the fuse and replace the front panel than to do the repair. This fuse failed at the end of the cleaning cycle for the bottom oven and left the door locked because the open fuse removed the 120v power from the control board. The locked door made it impossible to remove one of the screws holding the wall oven in place. However, after I ground off the head of the screw behind the edge of the locked door I was able to... Read more

The lightbulbs were a problem for me as I did not know if they were 12 V or 120 V. But the interactive parts diagram on the website was very helpful and allowed me to order the correct bulbs very rapidly(120V is correct). They were very easy to change out except for the fact that I needed to have my 12-year-old son do part of it since his hands are smaller than mine.(and it is always good for sons to work with dads even on small projects like this.) The cooking element was also amazingly easy... Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

Ordered a replacement panel. Item arrived exactly as described. Used the Youtube instructions. Took all of 5 minutes to replace. Thanks! Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

Ordered part and installed it. Broiler works as advertised. Read more

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replaced the elements with new ones ordered through Appliance Parts Pros. I wanted to tell you how pleased I am that I ordered the baking and broiler elements for my Maytag oven from you. Your website diagrams for my model of oven helped immensely in figuring out what parts I needed. Your order process was easy and the parts arrived within two days just as stated. Best part of all, the new elements work perfectly! I will bookmark your site for future appliance part needs and I look forward to... Read more

Removed the light covers, removed burned out bulbs, inserted replacement bulbs, reinstalled light covers. Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light

Called a repairman and he told us we needed to change a bunch of parts and would cost over $400! Decided to do some research online and found suggestions to replace the spark igniter. Decided to give it a try. Took about 10min to replace and oven is now working perfectly, for a total of $30! Read more