Parts for Ge JES1290ML01: 01 - Microwave Parts

The Microwave Door Switch is an OEM replacement part for GE microwaves. It is crucial for safety functionality as it detects when the door is properly closed and latched before initiating cooking cycles. The switch prevents operation if the door is ajar.

Causes of a bad door switch can include wear and grime accumulation over many years of use, impact damage, or failures in the plastic actuator or electrical components.

Symptoms of a bad door switch include:

• The microwave failing to start cooking even with the door closed and latched
• Error messages related to the door position being displayed
• Inability to lock or properly sense the closed door position

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This thermostat cavity is the molded housing that secures and protects the refrigerator thermostat and its sensing components, helping maintain correct sensor placement for reliable temperature control. Replaces a worn or cracked thermostat mount. What it does:

• Holds the thermostat and sensor in the correct position for accurate temperature sensing
• Protects thermostat and wiring from moisture, debris, and physical damage
• Keeps electrical connections and routing organized to prevent loose or pinched wires
• Can restore proper thermostat seating that may cause intermittent cooling or temperature control issues

• One thermostat cavity

• Disconnect power before starting any repair to avoid shock or injury
• Basic hand tools required; handle edges carefully to avoid cuts
• Retain and reinstall existing thermostat and sensor unless replacing them separately

This microwave magnetron thermostat is an authentic OEM part sourced directly from the manufacturer. It is used in microwave ovens to prevent fires and extensive damage to the machine if the magnetron overheats. If the thermostat reaches an unsafe temperature, determined by the factory, it will stop the microwave from cooking. If this happens, the magnetron thermostat may be the culprit and should be replaced. A built-in safety feature will prevent the microwave from working until the thermostat is replaced. To start, disconnect the power from the microwave. Use a screwdriver to remove the trim kit. Use a safety drill bit to remove the microwave panels. Locate the thermostat that is connected to the magnetron. To start, disconnect the wires and remove the thermometer from the microwave. Install the new thermostat and connect the wires. Reassemble the microwave and reconnect the power. Test to make sure the power works with the new thermostat installed.This magnetron thermometer is an electrical part that is sold individually. It is designed for use in microwave ovens manufactured by General Electric and Hotpoint.

This power cord assembly restores the main electrical connection to your appliance, providing a safe, routed supply line for consistent operation. Use it to replace a damaged, frayed, or non-functioning power cord and regain reliable power. What it does

• Replaces the appliance's main power cord to restore full electrical connection
• Fixes symptoms such as intermittent power, no power at the appliance, visible cord damage, or scorch marks at the cord connection
• Provides a factory-style replacement that routes and secures the cord where the OEM design intends
• Prevents unsafe operation caused by exposed or degraded wiring

• One factory-style power cord assembly

• Disconnect power at the breaker or unplug the appliance before beginning any work
• Route the cord through the strain relief and secure all terminal connections tightly
• If you see melting, corrosion, or damaged terminals, replace the mating parts.

This wiring harness connects the oven's convection components to the control system, restoring proper electrical routing for convection functions. Replacing a damaged harness helps recover fan operation and reliable signal transmission for convection cooking. What it does:

• Routes power and control signals between the oven control, convection fan motor and related convection sensors
• Prevents intermittent or lost convection function caused by broken, burned or loose wiring
• Stops arcing or shorting from frayed or damaged wires that can trigger error codes or shutdowns
• Ensures connectors mate securely to factory terminals for consistent operation

• One convection wiring harness

• Disconnect all power to the appliance at the breaker before starting any work
• Verify connector locations and orientation against the service diagram; replace only like-for-like
• Avoid pinching the harness against sharp edges or high-heat components; secure with clips or ties as used originally

The Primary and Secondary Door Switch is an OEM replacement part for GE microwaves. This part interrupts the power supply to the microwave when the door is opened.   

Causes of bad door switches can include regular wear and tear, electrical malfunctions, or physical damage from slamming the door.  

Symptoms of a bad Primary and Secondary Door Switch include:

• The microwave not starting or operating intermittently
• The appliance operating with the door open
• The interior light not turning on or off appropriately

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This latch slider is the replacement sliding component used in the door latch assembly to help secure the appliance door and enable proper latching. Replaces a worn or broken slider to restore reliable door engagement. What it does

• Slides along the latch assembly to engage or release the door catch for secure closing
• Helps the door fully latch so the appliance can start and run normally
• Common symptom: door won't latch or stays ajar even when closed
• Common symptom: door latch feels loose, sticks, or makes noise when operated

• One latch slider

• Disconnect power (and water if applicable) before starting any repairs
• Removing the door or front panel may be required to access the latch assembly
• Use basic hand tools; handle trim and glass carefully to avoid damage
• Verify proper alignment of the slider and latch after installation before restoring power

The Wave Guide Locking Button is an OEM part for GE microwaves. This small yet essential component secures the wave guide cover in place, ensuring that the microwave's internal components are protected from food particles and debris. It plays a key role in maintaining the microwave's efficiency and safety.

Causes of a bad wave guide locking button can include regular wear and tear, damage from frequent use, or accidental breakage. If the locking button is compromised, the wave guide cover may become loose, leading to potential damage or inefficiency in the microwave's operation.

Symptoms of a bad wave guide locking button include:

• Wave guide cover becoming loose or falling off
• Difficulty securing the wave guide cover in place
• Rattling noise inside the microwave
• Visible damage or wear on the locking button

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: This part is a quantity of one. Order quantity needed.

This replacement foot fits select GE microwaves. It provides a stable, cushioned contact point so the unit or its removable rack sits level, stays steady during operation, and helps protect surfaces from wear.

• Supports and cushions the microwave cabinet or a removable rack/accessory
• Helps keep the unit level to reduce wobble and vibration
• Protects interior and countertop surfaces from scuffs and marks
• Replaces missing, cracked, or flattened feet that cause rocking or rattling

• Disconnect power and allow the appliance to cool before servicing
• Remove the worn or missing foot and clean the mounting area
• Press or slide the new foot fully into place until secure
• The unit or rack sits level and stable before use

This is a light bu, and it is made for microwaves. This is a genuine replacement part made by General Electric. This specific light bu has a voltage of 120 and a wattage of 25.A new light bu might be needed if the current one does not turn on when the microwave door is opened. The light bu should also be on when the microwave is in use so that the user may see the food during the heating cycle. It is common for light bu to burn out over time and they are very easy to replace when needed.This is an OEM part sourced directly from the manufacturer. It is sold individually and is compatible with microwaves made by General Electric.

This tray glass is the replacement glass shelf used inside compatible ovens to hold cookware and bakeware safely. It restores a stable, heat-resistant surface so you can cook and clean with confidence. What it does:

• Provides a flat, heat-tolerant surface for pots, pans, and bakeware.
• Replaces cracked, chipped, or otherwise damaged glass that can interfere with stable cookware placement.
• Helps maintain the oven's intended cooking surface and makes cleanup easier.
• Fits into the oven's existing support rails and aligns with factory mounting points.

• One tray glass as shown

• Disconnect power to the appliance and ensure the oven is cool before attempting replacement.
• Handle glass with care; wear cut-resistant gloves to avoid injury from sharp edges.
• Remove oven racks and supports as needed to access and seat the new glass; confirm correct orientation before final placement.
• If the glass uses clips or brackets, ensure they are present and secure; replace any damaged fasteners per manufacturer guidance.

Replace a damaged U-shaped oven bake element with this exact-fit heater assembly to restore even baking and browning. Designed to slide into the oven cavity and heat reliably when the range is on. What it does:

• Heats the oven cavity for baking and roasting
• Provides even heat distribution across the oven bottom/top depending on placement
• Replaces cracked, burned, or non-heating elements that cause no-heat or uneven-heat symptoms
• Works with the oven's existing terminals and mounting bracket for a direct swap

• One U-shaped heater assembly

• Disconnect power to the appliance at the breaker before starting any repair
• Access typically requires removing the oven floor or back panel—use the OEM service manual for specific steps
• Handle the element carefully to avoid bending or damaging terminals; ensure tight, secure electrical connections

The Interlock Switch is an OEM replacement part for GE microwaves. It acts as a safety device that prevents the microwave from operating unless the door is securely closed and latched. The switch monitors the door position and communicates with the main control board to allow or cancel cooking functions.

Causes of failure may include damage from excess heat over time or wear from repeated door openings and closings. Failures can compromise safety if the microwave operates unexpectedly while open.

Symptoms of a bad interlock switch include:

• Microwave can be turned on even when the door is open     
• Error codes displayed related to door issues  
• Inconsistent or faulty communication with the control board

This genuine OEM replacement part is also compatible with GE, Hotpoint, and select Kenmore microwave models.

This bag screw assembly secures and fastens the appliance bag or liner, restoring proper fit and preventing shifting during operation. It's a direct-fit service part that helps maintain reliable performance. What it does:

• Fastens and secures the appliance bag or liner in place
• Prevents the bag from slipping or bunching during use
• Reduces noise and potential debris spillage caused by a loose bag
• Helps restore normal operation when bag movement is the symptom

• Disconnect power to the appliance before starting any repair
• Inspect surrounding components for wear; replace any damaged retainers or clips
• Use appropriate hand tools; avoid overtightening to prevent damage