Microwave Shaft Or Pin

This shaft assembly is a factory drive component used in select GE microwaves. It links the drive motor to its mating part to deliver smooth, reliable rotation, helping restore stable operation and consistent, even heating.

• Transfers motor rotation to the driven component for stable operation
• Replaces a worn or stripped shaft that can cause slipping or no rotation
• Helps resolve intermittent spinning, wobbling, or clicking/grinding from the drive area
• Restores consistent motion for more even cooking performance

• Disconnect power to the microwave before servicing; capacitors can hold a charge
• Access the drive area per your model (interior hub, underside panel, or top section)
• Align flats/splines and seat the shaft fully; reuse any original fasteners/retainers
• Reassemble and test for smooth, consistent rotation

A small metal pin used to secure components in place so they stay aligned and operate smoothly. Replaces a worn or missing retainer pin to restore proper fit and reduce rattling or movement. What it does:

• Secures moving or removable parts by fitting into a mating hole or bracket
• Prevents components from sliding out of alignment during use
• Commonly used where a simple, durable fastener is required
• Symptoms of a bad pin include loose parts, unwanted movement, rattling, or components that detach

• Disconnect power (or unplug appliance) before starting any repair
• Remove adjacent panels or components as needed to access the pin
• Use pliers or a punch to remove the old pin and press the new pin into place; avoid excessive force that could damage surrounding parts
• If the pin secures glass or sharp components, handle carefully and wear gloves and eye protection

This turntable shaft is the center coupler that links the microwave's turntable motor to the glass tray. Replacing a worn or cracked coupler restores smooth rotation so food heats more evenly without slips, stalls, or scraping.

• Couples the turntable motor to the tray for consistent rotation
• A worn or stripped hub can cause the tray to stop turning or turn intermittently
• Damage can lead to wobbling, slipping, or scraping noises at the center
• Loss of rotation can result in uneven cooking or cold spots

What's included: One turntable shaft Install notes:

• Disconnect power or unplug the microwave before servicing
• Remove the glass tray and roller ring; lift the old coupler straight up from the center
• Align the new coupler with the motor stem/key and press it fully into place
• Reinstall the roller ring and tray; verify smooth rotation with a microwave-safe cup of water

This piston assembly restores the moving piston used in the appliance's fluid/valve system to help recover proper dispensing and motion. It replaces a worn or damaged piston so the affected function can operate as intended. What it does:

• Replaces the piston that moves inside a valve or dispenser to control fluid or airflow
• Restores proper actuation and sealing that can prevent drips or improper dispensing
• Commonly installed when symptoms include poor dispensing, leaks near the valve area, sticking motion, or unusual noises during operation
• Works as a direct-fit replacement where this OEM piston assembly is specified

• One piston assembly as shown

• Disconnect power (and water supply or gas, if applicable) before starting any repair
• Follow the appliance service manual and use appropriate tools; keep small fasteners and seals organized
• Inspect sealing surfaces and O-rings; replace damaged seals to ensure a leak-free install
• Test the appliance after installation to confirm correct operation

This pin hinge is the pivot pin used in appliance doors to support and guide smooth opening and closing, helping restore proper door alignment and operation. What it does:

• Provides a secure pivot point for the appliance door to open and close smoothly
• Restores correct door alignment and helps prevent sagging or uneven gaps
• Helps the door latch and seal properly to maintain normal appliance performance
• Works as a replacement for worn, bent, or broken hinge pins

• Disconnect power and remove any stored product from the door area before starting
• Use basic hand tools; support the door while removing and installing the hinge to prevent damage
• Inspect surrounding hinge components and replace if worn to ensure proper alignment
• Wear gloves and eye protection; follow the appliance manufacturer's service instructions

This small metal pivot pin secures moving components so doors, hinges or trim stay aligned and operate smoothly. Replaces a worn or broken pin to stop rubbing, rattling and uneven movement. What it does:

• Acts as the pivot/retaining pin for a hinge or moving appliance trim piece
• Keeps door or trim aligned and prevents excessive play or sagging
• Stops metal-on-metal contact that can cause noise or wear
• Helps restore proper opening, closing and sealing performance
• Simple hardware replacement when the original pin is bent, broken or missing

• Disconnect power and remove food/items as required before starting repairs
• Support the door or component being worked on to prevent dropping during pin removal/installation
• Use appropriate hand tools; avoid excessive force that can bend the new pin
• If other hinge or trim components are damaged, replace them for best results