Microwave Fuse Or Sensor

• Won't start
• No heat
• not self-cleaning

Did some Google searches and most comments concerning this issue on LG stoves indicated the high temperature thermostat malfunctions when using the self cleaning function. This malfunction causes complete loss of power for the entire stove and locks the oven door. Since I wasn't completely sure if it was the thermostat or where it was for that matter, I called a service tech to troubleshoot the stove. He was able to determine it was the thermostat and further tested his findings by... Read more

I read on line about other such ovens doing the same thing mine was doing, absolutely nothing! I even read stories of a major retailer telling customers to throw the microwave away. There's nothing you can do to fix it. After replacing a simple fuse that I ordered from you, the Advantium is as good as new. It took a grand total of 5 minutes to make the repair. The shipping cost more than the part, but it was all very worthwhile. Read more

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more

• Won't start

Called AppliancePartsPros because of good experiencing diagnosing problem with a dishwasher repair. We definitely are modest income amateurs! Same excellent response to our questions. Three possible causes. Used easy search menu to fine replacement parts. Bought all three, knowing that if all not needed, the others could be returned (within 365 days) for refund. Replaced the capacitor successfully after calling to get more help with a couple of places where we got stuck. Oven now works... Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

I looked diligently for this probe for many months and to no avail. So desperate to find it , I Goggled and found this provider for the probe. I was amazed at the timing of the receipt of the item. I received an email within hours that it had been shipped the same day and arrived at my home within less than 48 hours! The price was great and the item was easy to locate on the site.. Thank you for your attention and customer service. I will use these folks again! Read more

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more

GE Microwave/Convection Oven. Removed case (carefully). Tested in-line power cord fuse with multi-meter. Fuse was good. Noticed a scorch mark on a wire connected to the oven cavity thermal fuse. The fuse appeared to have been overheated from too much movement in it's mount. Removed part from unit and used number on the part to order a new one. Installed new part, re-assembled, and unit works fine. Read more

Tried to turn the microwave on, checked the outlet for power, check the breaker to see if it was tripped, all was in order. Removed the over the range microwave and pull the covers, Tested continuity with a multimeter for each of the 4 normally closed thermostats, found 2 bad (open). The upper 110 and the lower right 70. Ordered the needed parts as well as both lamp sockets and bulbs as they where broken too. The parts where correct and where delivered on time. (Also, in your tools needed or... Read more

Went to Appliance Pros and found the part for my microwave. Web site was very easy to use. Ordered the thermal fuse and it was delivered in 2 days. Shipping was a a bit expensive, but can't complain with two day delivery. Replaced the failed part and the microwave now works great. It 1 1/2 hours, but I took my time. Needed one helper to remove the top screws. Handy-wife did it without a problem. Read more

Replaced the thermostat and it turned on and I have power again. Read more

• Won't start

I have a Jenn-Air microwave that didn't turn on and had no lights. It just stopped working completely. I unplugged the unit and had to remove the rear cover using a *security screw kit* that prevents people from opening the rear panel. Once opened, I removed the fuse and testing it with an OHM reader to determine that the fuse went bad. But I also had to determine why the fuse blew and noticed a sticky oily substance under the Capacitor. I used a rubber glove and needle nose pliers to... Read more

I contacted Appliance Parts Pros, and told them what the problem was and what it was doing. They sent me an email with the parts number needed to complete the repair. This was a built in a cabinet unit and I required help removing it and reinstalling it. The repair was relative easy once I had the parts and it took approximately four hours,. It took longer getting to the defective parts than replacing them. ... Read more

The wonderful parts pros on the phone said that it was probably the diode or the magnetron. So we tried the cheapest way first and it worked so happy to have my microwave back and working for only a few dollars rather buying a new appliance. Read more

• Exhaust fan not working
• shuts off after a few seconds

I attempted to diagnose the four thermostats/thermal switches in the microwave....two right behind the control panel, one on top of the cooking cabin, and one under a metal shroud above the magnetron. While checking continuity with a voltmeter, i questioned one of them behind the control panel and the one above the magnetron. I then noticed a burn mark on the plastic connector sleeve for the one above the magnetron. I took a scrap piece of 14 gage copper wire and beat the ends flat with a... Read more