Parts for Ikea ISC21CNEDS00: Motor And Ice Container Parts

Mounting bracket for side-by-side refrigerators. Secures internal components in place. Replace if cracked, bent, or broken to restore stability.

Ice dispenser not working or only dispensing sometimes? The auger motor powers ice ejection from the storage bin. DIY-friendly repair in under an hour.

Ice won't switch between crushed and cubed? The dispenser solenoid controls the crusher mechanism. Most DIYers replace it in 25-30 minutes with basic tools.

This is a mounting bracket or guide used in the ice dispenser area of a refrigerator. It supports and positions the dispenser solenoid or related components to ensure proper alignment and operation. Replace this part if the ice dispenser is not functioning correctly, the solenoid is loose or misaligned, or if the bracket is cracked or broken.

Ice dispenser not working or coupling spins freely? This motor coupling connects the dispenser motor to the auger. 10-minute fix with channel lock pliers.

Stores and dispenses ice in your freezer. Replace if cracked, broken, or worn to restore proper ice handling and prevent jams or leaks in your unit.

Step spacer for refrigerators. Installs between components to maintain proper alignment and spacing. Replace if cracked, broken, or missing.

Replacement spacer for refrigerators. This small structural component maintains proper spacing between parts. Order a new spacer if yours is missing.

Fix ice that won't crush or dispense with this refrigerator crusher blade. Solves bent or damaged blades preventing ice from dispensing. Easy DIY repair.

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

Ice crusher not working or producing inconsistent crushed ice? This rotating crusher blade restores proper ice crushing when worn, bent, or cracked.

This is a small coupling washer that connects the ice crusher drive mechanism in the refrigerator's freezer compartment. It transfers rotational force from the motor to the ice crushing blades, allowing the dispenser to crush ice properly. Replace this part if the ice dispenser runs but does not crush ice, makes grinding noises, or if the coupler appears worn, cracked, or stripped.

Secures rotating shafts and levers in your refrigerator's ice dispenser mechanism. Replace if pin is sheared, worn, or missing to restore alignment.

Fix ice dispenser issues with this refrigerator ice crusher auger. Solves crushed ice not dispensing or jamming problems. Direct fit replacement part.

The Ice Dispenser Drum is an OEM replacement part for Whirlpool refrigerators. This drum is located in the ice maker assembly and is responsible for dispensing ice when activated. It rotates to push ice through the chute and into your glass or container.

Causes of a bad ice dispenser drum include wear and tear from regular use, damage from ice jams, or breakage due to accidental mishandling. Accumulation of ice and debris can also cause the drum to malfunction.

Symptoms of a bad ice dispenser drum include:

• Ice not dispensing properly
• Grinding or clicking noises during operation
• Inconsistent ice output
• The dispenser becoming jammed frequently

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Ice dispenser jammed or grinding? A cracked baffle prevents smooth ice flow. This support aligns the auger inside the bin. Moderate DIY with video guide.

This bearing nut secures a bearing and related rotating components on the shaft, keeping the assembly tight and aligned for smooth, dependable operation. Replacing a worn or stripped nut helps stop wobble, noise, and drive slippage.

• Locks the bearing/stack onto the shaft to prevent loosening
• Maintains alignment for smooth rotation and reduced vibration
• Helps restore consistent drive in shaft-driven assemblies
• Typical symptoms: loose or non-turning drive, rattling/grinding, or visible thread damage

• Disconnect power before servicing; shut off water if working near dispenser components
• Remove the related assembly to access the shaft; note part order for reassembly
• Hand-start the nut to avoid cross-threading; verify thread direction against the original
• Tighten securely; inspect the bearing, washers/spacers, and shaft for wear

Fix an ice maker that won't stop making ice or overflows the bin. This ice maker control arm regulates ice production cycles in side-by-side models.

Return spring provides tension for ice maker levers, door latches, or control rods. Replace if broken, stretched, or missing to restore proper snap-back.

Secures support rods or shafts to keep moving parts aligned in your refrigerator. Replace if the clip is broken, worn, or missing to prevent rattling.

Ice not dispensing properly or spilling? This crusher housing secures ice-crushing components and guides crushed ice to the chute. Fixes cracked housings.

This ice deflector guides ice cubes from the icemaker into the ice bin to help keep ice delivery consistent and reduce cube jams or spills. It's a simple replacement that restores proper ice routing in compatible refrigerators. What it does:

• Directs ice cubes from the icemaker into the ice bin for orderly dispensing
• Helps prevent ice clumping and blockages that can stop ice flow
• Keeps ice moving away from the icemaker assembly and into the bin
• Restores proper alignment and function after a cracked or missing deflector

• Disconnect power to the refrigerator before servicing to avoid electrical or mechanical injury
• Remove the ice bin or access panel per your model's service instructions to reach the deflector
• Part typically snaps or slides into place; reuse existing fasteners unless new hardware is supplied
• After installation, reconnect power and run the icemaker through a cycle; discard any ice made during the repair if contamination is suspected

Flat plain washer that distributes load and spaces hardware on appliance assemblies. Replace if worn, missing, or needed for secure fastening.

Secures components to prevent axial movement and rattling. Replace worn rings to restore quiet, stable operation. Confirm fit with your model number.

Covers and protects the ice container in your refrigerator. Replace if cracked, broken, or missing to keep ice fresh and prevent contamination.

Replace your refrigerator's interior light bulb when dimming, flickering, or burnt out. Restores visibility inside fridge and freezer compartments.

Replace your cracked or cloudy dispenser light lens to restore clear illumination. Protects the bulb and improves visibility. Verify fit with your model.

Ice dispenser not working or auger keeps falling off? This coupling connects the motor to the auger. Simple 15-minute DIY fix restores ice dispensing.