Parts for Electrolux EIMED55IIW3: 05 - Motor Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Outlet Thermal Fuse is an OEM part for Frigidaire dryers. It acts as a safety device that protects the dryer from overheating by cutting off the power if the temperature exceeds a safe level. This ensures the dryer operates safely and helps prevent potential fire hazards.

Causes of a bad thermal fuse can include lint buildup blocking airflow, overloading the dryer, or mechanical failures in the heating element. These issues can cause the dryer to overheat, leading to the fuse blowing as a protective measure.

Symptoms of a bad outlet thermal fuse include:

• The dryer not starting
• The dryer running but not heating
• Sudden stopping during a cycle
• No power to the dryer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This dryer blower moves air through the drum, lint filter, and exhaust so laundry dries efficiently. Replacing a damaged blower restores proper airflow and helps prevent long dry times and overheating issues.

• Draws and circulates air across the heater, through the drum and lint filter, and out the vent
• Maintains correct airflow and temperature control for consistent drying performance
• Worn, cracked, or clogged blowers may cause weak exhaust airflow and extended dry cycles
• May also present as rattling/grinding noises from the blower area or high-heat shutoffs

• Disconnect power; if gas, turn off gas supply before servicing
• Access the blower by removing the front/lower panel and blower cover
• Clean lint/debris from the housing and duct; transfer any seals or hardware from the original as needed
• After installation, spin the blower by hand to verify free movement; reassemble and test airflow

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

Replace a failed thermistor with this factory temperature sensor. It monitors temperature and feeds that data to the control, helping the appliance regulate heat and run cycles correctly. A faulty sensor can cause temperature-related performance issues.

• Senses temperature and sends a resistance signal to the control board for regulation
• Helps maintain proper heating/temperature during operation
• Failure may cause no heat or overheating, erratic or extended cycles, or temperature/sensor error codes
• Replace when sensor is open/shorted or readings are out of range per service diagnostics

• Disconnect power before servicing; if applicable, also shut off water or gas supply
• Access the sensor, unplug the wire connector, and remove any mounting screw/clip
• Install the new sensor; transfer any bracket/seal from the original and route wiring away from hot or moving parts
• Run a diagnostic or test cycle after replacement to confirm normal operation

This hex head screw spacer is a replacement threaded fastener that secures and spaces components while cutting its own thread in softer mating material for a tight fit. It's useful for repairs where the original spacer screw is missing or damaged. What it does:

• Acts as a spacer and fastener to hold panels, brackets, or assemblies at a set distance
• Thread-cutting tip forms secure threads in compatible materials for reliable engagement
• Helps stop movement or vibration of connected parts that can cause noise or wear
• Commonly used where the original hex-head spacer screw is corroded, stripped, or broken

• Use the correct screwdriver or wrench on the hex head to avoid rounding the fastener
• Start threads straight and apply steady pressure; do not force if resistance indicates misalignment
• Use appropriate torque — overtightening can strip the formed threads or damage parts
• Wear eye protection and follow appliance power/disconnect safety before servicing

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

The Idler Arm Assembly is an OEM replacement part for Frigidaire clothes dryers. It is a pulley assembly that helps to guide the dryer belt and keep it aligned. The idler arm assembly is typically located on the front of the dryer, near the dryer drum.

Causes for replacement include worn bushings or broken linkage from constant mechanical movement over several years.

Symptoms of a faulty idler arm assembly are:

• Dryer drum failure to rotate or revolve during the cycle
• Unusual vibrations, clunks, or knocks from within the dryer
• door during operation
• Slipping or shredding belts from lack of pulley engagement

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drive Belt is an OEM replacement part for Frigidaire dryers. It plays a crucial role in transferring the rotational motion from the dryer's motor to the drum, enabling the tumbling action necessary for drying clothes.

Symptoms of a need to replace the drive belt include:

• The dryer drum not turning or rotating during cycles
• Loud thumping or squeaking noises coming from the dryer
• Visible wear, cracks, or fraying on the existing belt

Causes of a faulty drive belt can include general wear and tear over extended use, exposure to high temperatures or lint buildup, physical damage from foreign objects, or manufacturing defects in the belt material or construction.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models. 

The Motor Mounting Clamp is an OEM part for Frigidaire dryers. This clamp secures the motor in place within the dryer, ensuring it operates smoothly and remains stable during the drying cycles. The motor mounting clamp is essential for maintaining the proper alignment and function of the dryer motor.

Over time, the motor mounting clamp can become worn out or damaged due to constant vibration and movement. Accidental impacts or mishandling during maintenance can also cause the clamp to fail, leading to motor misalignment or instability.

Symptoms of a bad motor mounting clamp include:

• Excessive noise or vibration during the drying cycle
• Motor shifting or moving within the dryer
• Reduced drying efficiency
• The dryer not starting or stopping abruptly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dryer Motor is an OEM part for Frigidaire dryers. It is responsible for turning the drum and the blower wheel to circulate air through the dryer, enabling efficient drying of clothes.

The dryer motor can become faulty due to normal wear and tear, electrical issues, or overheating. If the motor fails, the dryer will not be able to operate correctly.

Symptoms of a bad dryer motor include:

• The drum not spinning
• The dryer not starting or shutting off mid-cycle
• Unusual noises such as humming, buzzing, or grinding
• A burning smell or overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a mounting bracket that secures and supports appliance components, helping keep panels and assemblies aligned for stable operation. It's a simple replacement part that restores proper fit and reduces movement or rattling. What it does:

• Secures and supports a panel or internal assembly to the appliance frame
• Keeps components aligned to prevent binding or misalignment
• Reduces vibration and rattling caused by loose fittings
• Restores proper mechanical support after breakage or wear

• Disconnect power and/or water to the appliance before beginning any repair
• Use appropriate hand tools; keep track of fasteners and any shims or clips
• Beware of sharp sheet-metal edges; wear gloves and eye protection

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement pulley guides the drive belt so the drum or tub turns smoothly and reliably. A worn pulley can squeal, shred belts, or stop the load from tumbling or spinning.

• Guides the drive belt and helps transfer motor power to the drum/tub
• A seized or damaged pulley can cause the drum/tub not to turn or to stall
• Inspect for cracks, wobble, or rough bearings during diagnosis

• Disconnect power before servicing; if working on a gas dryer, also shut off the gas supply. For washers, turn off water.
• Access the belt path; release belt tension and remove the old pulley.
• Install the new pulley and route the belt correctly; rotate by hand to confirm smooth tracking.
• Inspect and replace a worn drive belt or related belt-drive components while open.