Parts for Frigidaire GPDB698JC0: 05 - Motor Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishes not drying or staying wet after cycle? This heating element heats water for cleaning and air for drying. Most DIYers replace in under 30 minutes.

Secures the lower spray arm in place. Replace if tabs are broken, worn, or missing, causing the spray arm to detach or not lock down properly. Installs under filter.

Seals the connection between the dishwasher tub and sump assembly. Replace if water leaks from the base or the gasket appears cracked or flattened.

Secures the sump assembly and pump seal to prevent leaks and maintain proper water flow. Replace if damaged or during sump repairs. Confirm fit with model.

Replacement center spray arm for your dishwasher. Installs in the middle spray position. Order a new one if yours is melted, cracked, or clogged.

Replaces a cracked, broken, or damaged lower spray arm in your dishwasher. Snaps into the bottom sump assembly. Essential for proper water distribution.

Replacement nozzle kit for dishwasher center spray arm. Needed when nozzles are clogged, cracked, or missing, preventing proper water distribution.

Seals the upper spray arm delivery tube connection in your dishwasher. Replace if water leaks from the spray arm mount or arm becomes loose. Verify fit.

Red

Replaces cracked, split, or rodent-damaged connector hoses that route water between internal dishwasher components. Essential when the original hose leaks.

This small check ball sits inside the dishwasher's drain pump or water inlet valve and acts as a one-way valve to prevent water from flowing backward through the system. It ensures water moves in the correct direction during wash and drain cycles. Replace this part if you notice water draining back into the tub after a cycle completes, the dishwasher isn't draining properly, or water is leaking from the pump area.

Noticeable wear, cracks, or deformation on the O-ring This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Seals the rear of your dishwasher's circulation pump to prevent leaks. Replace if you notice water pooling or dripping from the motor area.

Replacement nozzle kit for dishwasher center spray arm. Needed when nozzles are clogged, cracked, or missing, preventing proper water distribution.

This is a plastic support bracket that holds the lower spray arm in place at the bottom of the dishwasher tub. It allows the spray arm to spin freely while maintaining proper water flow from the pump to the arm. Replace this support if the lower spray arm wobbles excessively, detaches during cycles, or if dishes on the bottom rack are not getting clean due to reduced water pressure.

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

Houses and seals the dishwasher's filter screen to trap food debris and prevent recirculation. Replace if loose, cracked, or dishes remain dirty after cycles. Confirm fit by model number before ordering.

Prevents debris from clogging your dishwasher drain. Replace if parts won't lock in place, wobble during cycles, or show wear. Twists to lock securely.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Stainless steel screw that secures the dishwasher impeller assembly. Replace if stripped, corroded, or missing to properly mount the impeller.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

NO.8 - .625 Truss

Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Order when original screw is stripped, missing, or broken.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

No.10 - 16 x 3/8

Replacement mounting screw that secures control switches and switch assemblies to the dishwasher panel. Needed when original hardware is lost or stripped.

Secures dishwasher wire harness and prevents moisture from reaching the dispenser assembly. Replace if cracked, loose, or causing electrical issues.

NO.8 - .625 Truss

Replacement mounting screw for dishwasher panels and internal components. Needed when original screws are stripped, missing, or corroded during repairs.

Stainless steel screw that secures the dishwasher impeller assembly. Replace if stripped, corroded, or missing to properly mount the impeller.

Phillips head mounting screw for dishwashers and ranges. Secures internal components and panels. Replace if stripped, rusted, or missing during repairs.

No.10 - 16 x 3/8

10 - 16 x 3/8 , hex

F117-20 These are normally open thermostats

Temp boost, high temp wash These are normally open thermostats

This replacement part is a bushing, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. This bushing is typically found in dishwashers but is compatible with other devices as well. The bushings are an important part of many appliances as they help reduce friction inside the machine during the different washing cycles. A new bushing might be needed if the current ones are broken or damaged. It is common that different machinery needs multiple types of bushings. These small but important parts are placed around tubes or poles and are meant to assist during the rotating or sliding mechanisms. Be sure the machine is completely powered off as the area with the bushings is often hot from friction. See the owner's manual for more exact instructions before attempting to replace this part. These bushings are sold separately and are OEM replacement parts. These bushings are compatible with appliances made by Frigidaire.

Replacement mounting screw for dishwasher panels and components. Secures loose panels, brackets, and trim. Needed when original fasteners are missing, stripped, or worn.

Replacement mounting screws that secure your cooktop to the countertop or cabinet. Essential when original screws are stripped, missing, or damaged during installation or service.

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Precision shoulder screw for dishwashers. Locates and pivots components, keeping panels and moving parts aligned. Replace when worn, missing, or broken.

Plastic dispenser mounting screw for dishwashers. Secures detergent dispenser assembly to door. Replace if stripped, cracked, or missing.

Replacement cabinet insulation panel for dishwashers. Installs inside cabinet to reduce heat transfer and noise. Needed when original is torn, compressed, or missing.

Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Order when original screw is stripped, missing, or broken.

Replaces missing, torn, or saturated sound-dampening insulation blanket for dishwashers. Wraps around tub to reduce noise and protect cabinetry.

This side mounting bracket kit includes the hardware needed to secure a dishwasher to the adjacent cabinetry from the sides rather than from the countertop. It is commonly used in kitchens with granite, stone, or other countertops where top-mounting screws cannot be used. Replace this kit if the original brackets are bent, broken, or missing, causing the dishwasher to shift or slide during operation.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.