Parts for Ge EDW2020F01BB: 03 - Motor-Pump Mechanism Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Dishwasher not draining or leaving water in the bottom? This pump and motor assembly circulates and drains water. 2-hour DIY repair with video guide.

Mounting bracket that secures the dual pump assembly in your dishwasher. Replace if bracket is cracked, broken, or missing to properly support pump.

Replacement mounting screw for dishwashers. Secures internal components, panels, and brackets. Needed when original screws are stripped, missing, or lost.

This kit is used to repair a leaking pump on GE made dishwashers. For a complete pump/motor assembly get WD26X10013.

Secures dishwasher sump to tub, maintaining seal compression to prevent leaks. Replace if corroded or weak. Confirm fit with your model number.

Fix dishwasher leaks from cracks or tears in the pump connector. Requires removing dishwasher and pump access. Video guide available for DIY repair.

A replacement clamp that secures hoses or wiring to keep lines routed and stable, helping prevent rubbing, leaks and noise. Restores a reliable hold for tubing and harnesses so the appliance runs quietly and safely. What it does:

• Holds hoses, tubing or wire harnesses in place to reduce movement and chafing.
• Helps prevent leaks and water line abrasion caused by loose fittings.
• Reduces rattling or vibration from unsecured lines or cables.
• Keeps routing organized so adjacent components aren't stressed or worn.

• Disconnect power before servicing the appliance; shut off water supply when working on water or drain lines.
• Remove the old clamp and position the replacement so it fully engages the hose or harness, avoiding twists.
• Use appropriate hand tools (pliers or screwdriver) and secure the clamp evenly; avoid overtightening.
• Inspect surrounding hoses and wiring for damage while installing; replace any components that show wear.

Replacement lower spray arm assembly for dishwashers. Installs at the bottom of the tub. Needed when the spray arm is cracked, broken, or tabs damaged.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

The Filter & Gasket Assembly is an OEM part for GE dishwashers. This part traps food particles and debris during the wash cycle, preventing them from redepositing on dishes or clogging the drain system. 

Causes of a bad Filter & Gasket Assembly can include wear and tear from regular use, accumulation of hard water minerals or detergents affecting the gasket's seal, and damage to the filter mesh that allows larger particles to pass through or clog the assembly.

Symptoms of a bad Filter & Gasket Assembly include:

• Poor cleaning performance, with food particles left on dishes after a cycle
• Water leakage around the dishwasher's base, indicating a compromised gasket
• Unpleasant odors from trapped food particles that are not properly filtered out

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This pushnut fastener is a small push-on retainer used to secure shafts, rods, or trim where a threaded fastener isn't required. It provides a secure hold while allowing quick, tool-free installation for maintenance or repairs. What it does:

• Secures axles, shafts, or trim pieces by gripping the mating shaft with a one-way push-on design
• Keeps panels, knobs, or small components from sliding off during operation
• Helps stop rattles or loose parts caused by worn or missing retainers
• Simple, non-threaded solution where a reusable bolt or clip isn't needed

• One pushnut fastener

• Press onto clean, appropriately sized shaft until fully seated; do not hammer with excessive force
• Wear eye protection when installing small retainers to prevent injury from sudden release
• Replace with identical part number to ensure correct fit and retention
• Use appropriate pry tools or cutters to avoid damaging surrounding parts

Dishwasher service dome coarse filter traps food debris during wash cycles. Replace if leaking, cracked, or worn to prevent water leaks. Verify fit by model.

Secures dishwasher drain or inlet hoses to fittings to prevent leaks and slipping. Replace when loose, corroded, or during hose installation. Verify fit.

Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

Replacement hex head screw for dishwasher component mounting. Secures solenoids, valves, and internal parts. Order when original is rusted, stripped, or missing.

Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.