Parts for Gibson GDB742RJS2: 09 - Motor & Pump Parts

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

Dishes not drying or staying wet after cycle? This heating element heats water for cleaning and air for drying. Most DIYers replace in under 30 minutes.

Secures the lower spray arm in place. Replace if tabs are broken, worn, or missing, causing the spray arm to detach or not lock down properly. Installs under filter.

Seals the connection between the dishwasher tub and sump assembly. Replace if water leaks from the base or the gasket appears cracked or flattened.

Secures the sump assembly and pump seal to prevent leaks and maintain proper water flow. Replace if damaged or during sump repairs. Confirm fit with model.

Replacement center spray arm for your dishwasher. Installs in the middle spray position. Order a new one if yours is melted, cracked, or clogged.

Replaces a cracked, broken, or damaged lower spray arm in your dishwasher. Snaps into the bottom sump assembly. Essential for proper water distribution.

Seals the upper spray arm delivery tube connection in your dishwasher. Replace if water leaks from the spray arm mount or arm becomes loose. Verify fit.

Red

Replaces cracked, split, or rodent-damaged connector hoses that route water between internal dishwasher components. Essential when the original hose leaks.

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

Seals the rear of your dishwasher's circulation pump to prevent leaks. Replace if you notice water pooling or dripping from the motor area.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.

The Front O-Ring is an OEM part for Frigidaire dishwashers. This component is essential for maintaining a watertight seal in the front areas of the dishwasher's internal systems, such as around the pump or valve connections. It prevents water leaks and ensures the efficient operation of the dishwasher. The rear O-ring is part number AP2109101

Causes of a bad front O-ring can include regular wear and tear, exposure to high temperatures, and chemical degradation from detergents and rinse aids. Over time, the O-ring may dry out, crack, or become deformed, leading to leaks and decreased performance.

Symptoms of a bad front O-ring include:

• Water leaking from the front of the dishwasher
• Puddles forming under the appliance
• Reduced cleaning performance due to water pressure issues
• Noticeable wear, cracks, or deformation on the O-ring

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Mounting bracket that secures the lower spray arm to the dishwasher sump. Replace if cracked, broken, or missing to prevent spray arm detachment or tilting.

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:

• Provides structural support for the appliance cabinet and mounting points
• Keeps internal components aligned and maintains correct clearance
• Helps prevent rocking, vibration and gaps at the bottom of the cabinet
• Protects lower components from contact with floor-level debris or uneven surfaces

• Disconnect power and, if applicable, water before beginning work
• Access may require removing the toe kick or lower access panels
• Keep track of mounting screws and brackets; use replacement hardware if original fasteners are corroded

Filters debris from dishwasher sump to protect pump and spray arms. Replace if warped, clogged, or dishes aren't cleaning properly. Verify fit by model.

Prevents debris from clogging your dishwasher drain. Replace if parts won't lock in place, wobble during cycles, or show wear. Twists to lock securely.

Dishwasher leaking or not washing dishes? The circulation pump motor controls water flow. Most DIYers complete this repair in 30-60 minutes.

Secures dishwasher hoses to prevent leaks and water damage. Replace if loose, cracked, or leaking. Verify fit with your model number before ordering.

NO.8 - .625 Truss

No.10 - 16 x 3/8

Secures water or drain hoses to fittings, preventing leaks and loose connections. Replace when hoses slip or drip to restore a tight seal.

Brass nut that secures the heating element to the dishwasher tub. Replace if cracked, split, or causing leaks around the element mounting area.

Removes residue, odor-causing soils, and food particles from dishwasher tub and gasket. Use monthly to eliminate unwanted odors and maintain peak performance.