Parts for Ikea 30469294: Oven,Cabinet Parts

Microwave not responding to buttons or display blank? This electronic control assembly manages all oven functions and user interface. Moderate DIY repair.

A complete door assembly that replaces a damaged, dented, or non-sealing appliance door to restore proper closure and appearance. Fits the original mounting points for straightforward swap-out. What it does:

• Replaces a cracked, dented, or bent door so the appliance seals and functions correctly
• Restores the exterior appearance and protects internal components from damage
• Helps prevent temperature loss or improper cooking/cooling caused by a damaged door
• Eliminates rattling or binding caused by warped or broken door structure

• Disconnect power and follow all safety steps in your owner's manual before starting
• Door assemblies are heavy or awkward—use two people to avoid injury or product damage
• Retain and reuse any original screws or brackets unless replacement hardware is provided
• Refer to the OEM service instructions for hinge alignment and final adjustment

Replaces cracked, burned, or missing waveguide cover in your microwave. Protects the magnetron opening from food splatter and moisture damage.

The Mounting Kit is an OEM part for Frigidaire microwaves. It provides the necessary hardware to mount a built-in microwave securely above a cooktop or range. The mounting kit contains mounting brackets, and screws to facilitate a safe and sturdy installation. This kit does not include the installation instructions.

Causes of a bad mounting kit can include deterioration of mounting brackets or screws over time and repeated use, or if the original kit was missing components needed for a secure installation.

Symptoms of a bad or missing mounting kit include:

• The microwave become loose or detached from the wall
• Screws fall out or strips during installation
• Brackets bend or break over time
• Microwave is not level after installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

Support ring installs beneath the microwave turntable to provide stable, balanced rotation. Replace if cracked, broken, or missing for proper use.

Connects the motor to the glass turntable tray in your microwave. Replace if cracked, broken, or worn to restore smooth tray rotation and proper cooking.

Fix weak ventilation or loud operation in your microwave hood combo with this fan motor. Moderately challenging repair that restores proper airflow.

Clear plastic lens cover for microwave interior or hood lights. Snaps over bulb assembly. Replace when cracked, yellowed, or missing. Easy DIY fix.

Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-1/16" x 7-5/8" x 3/32" (5.0625 x 7.625 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

The Lamp is an original and genuine OEM replacement part for Frigidaire microwaves. It is located inside the microwave and provides light to easily see food and monitor cooking progress.

Causes of a bad lamp can be natural bulb burnout over time, damage from foods accidentally jostling the lamp during cooking, or general wear and tear.

Symptoms of a bad lamp include:

• Dimming or flickering light inside the microwave when in use
• No light turning on when the microwave is powered on
• Broken or cracked bulb housing

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement vent grille cover for microwaves and microwave/hood combos. Installs on the exterior housing to cover ventilation openings. Needed when cracked, broken, or missing.

This temperature control thermostat regulates the refrigerator's cooling cycle to help maintain set temperatures in the fresh food compartment. Replaces a failed thermostat to restore proper compressor cycling and temperature control. What it does:

• Senses cabinet temperature and cycles the compressor on and off to maintain the selected setting.
• Stops cooling when the set temperature is reached and restarts cooling as temperatures rise.
• Commonly used when the refrigerator is running constantly, not cooling, or temperatures are inconsistent.
• Works with the control knob/capillary assembly to provide user-adjustable temperature control.

• Disconnect power to the appliance before attempting service.
• Access typically requires removing the control knob and control housing; handle the capillary tube gently to avoid kinks.
• Verify correct replacement location and routing before reassembly; test operation after restoring power.

Microwave won't start or is completely dead? This fuse protects against electrical overload. Requires disassembly to access. Often replace with switches.

This is an electrical noise filter designed to suppress electromagnetic interference generated by the microwave's internal components. It connects inline with the power supply to prevent electrical noise from affecting the microwave's operation or other nearby electronics. Replace this filter if your microwave displays erratic behavior, produces unusual buzzing sounds, or interferes with other appliances on the same circuit.

Fix an air conditioner that won't start or runs poorly. This compressor start/run capacitor restores motor operation and improves cooling performance.

Adhesive mounting tape for microwave interior and exterior components. Replace when tape loses adhesion, becomes worn, or parts detach. Secures panels.

Molded protective housing cover that shields internal microwave components from dirt and debris. Replace if cracked, broken, or missing to maintain safety.

The Latch Hook is an OEM replacement part for Frigidaire microwaves. It is an internal component that helps securely latch and lock the microwave door during operation. The latch hook works with the door handle mechanism to ensure the door is properly fastened to prevent leaks of microwave energy and for safety. 

Causes of a bad latch hook can include wear and tear over time, damage from repeated use of the door latch, or issues with the latch hook spring or connecting components. 

Symptoms of a bad latch hook include:

• The microwave door not closing or latching securely  
• Difficulty closing or popping open the door during a cycle
• Leaks of microwave energy from around the door seals
• Error codes related to door-latching problems

This OEM Frigidaire replacement part is also compatible with Electrolux, Westinghouse, and Kelvinator microwaves. 

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

Microwave won't start or runs with door open? This door switch detects when the door is closed for safe operation. Common wear part. DIY repair.

This replacement switch restores reliable on/off control to the circuit it serves. When the original wears out or overheats, installing a new switch can resolve non-responsive controls and intermittent operation so your appliance functions as intended.

• Opens and closes an electrical circuit when actuated by the appliance's lever, button, or mechanism
• A failed switch can cause no response, intermittent operation, or components that won't turn off
• Common signs include a stuck/loose actuator or burned/broken terminals
• Continuity testing with a multimeter can switch failure

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Note/photograph wire locations and transfer one lead at a time to matching terminals
• Use needle-nose pliers to remove spade connectors—do not pull on the wires
• Verify continuity and test operation before reassembly

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch detects door position. Moderate DIY repair.

This mechanical thermostat controls refrigerator temperature by sensing evaporator or cabinet temperature and switching the compressor and fans on and off. Replaces a worn or faulty control to help restore consistent cooling and temperature regulation. What it does

• Senses temperature and closes/open circuit to run the compressor and cooling fans
• Helps maintain set temperature by cycling refrigeration system components
• Commonly linked to symptoms like warm or fluctuating temperatures, compressor not running, or continuous running
• Works as the control point for user temperature settings

• One thermostat

• Disconnect power to the appliance before accessing controls to avoid shock or injury
• Access may require removing interior panels or control housing
• Handle sensing bulb and capillary tube carefully to avoid kinks or damage

Microwave not heating food? The magnetron generates the microwaves that cook your food. A failed magnetron is the most common cause of no-heat issues.

This is a cooling fan motor used in a microwave oven to circulate air and prevent internal components such as the magnetron and electronics from overheating. It typically runs during cooking and may continue running briefly after the microwave shuts off. Replace this motor if the microwave is overheating, shutting off unexpectedly, or if the fan is noisy, runs sluggishly, or doesn't spin at all.

This fan blade mounts to the refrigerator fan motor to move air through the appliance for proper cooling and temperature circulation. Replaces a worn or damaged blade to restore airflow and improve cooling efficiency. What it does:

• Spins on the fan motor to circulate air across the evaporator or condenser coils
• Restores proper airflow when a cracked or broken blade causes reduced cooling
• Helps stop vibration or rattling caused by bent or missing blades
• Can reduce motor strain from an imbalanced or damaged blade

• Disconnect power to the appliance before starting any repair
• Remove access panels and fan shroud to reach the blade; keep track of mounting hardware
• Replace carefully to avoid bending the blade; ensure correct orientation on the motor shaft

The Thermostat is an OEM part for Frigidaire microwaves. The thermostat accurately monitors interior temperature levels during operation.

Symptoms of a faulty thermostat include:

• Inconsistent or uneven cooking results from inaccurate sensing  
• Continuous running even after the set time elapses
• Error lights or temperature faults displayed 

Failure usually occurs due to a gradual loss of calibration from years of thermal cycling stress or corrosion buildup damaging electrical components. Replacement is needed to restore precise temperature regulation.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models. 

This thermostat monitors the internal temperature of the microwave and helps regulate heating to prevent the appliance from overheating. It acts as a safety device that cuts power to certain components if temperatures exceed safe limits. Replace this thermostat if the microwave shuts off unexpectedly during use, fails to heat properly, or if diagnostic testing shows the thermostat is no longer opening or closing at the correct temperature.

Microwave not heating or display not working? This control transformer supplies low-voltage power to electronic components. Moderate DIY repair.

Retainer bracket for microwaves. Secures internal components in place. Replace if broken, cracked, or missing to restore proper fit and stability.

This high voltage capacitor works with the diode and magnetron to generate the microwave energy needed to heat food. It stores and releases electrical energy to nearly double the voltage output from the transformer. Replace this capacitor if the microwave runs but does not heat, makes a loud buzzing noise, or if the unit trips a breaker - always discharge the capacitor before handling as it can retain a dangerous charge even when unplugged.

Microwave not heating or making buzzing noises? This diode rectifier allows current flow in one direction and protects circuits. DIY repair takes 30 minutes.

Replacement air vent grille for microwaves. Mounts to the cabinet to direct airflow. Needed when the original grille is cracked, broken, or missing.

Secures internal components to the microwave chassis. Replace if cracked, broken, or missing to restore proper support and stop rattling or misalignment.

This outer cabinet is the main housing that supports and encloses the refrigerator compartment, restoring the unit's structural support and finished appearance. Replaces a damaged, dented, or corroded outer shell to help maintain proper door alignment and insulation coverage. What it does

• Provides the main structural enclosure for the refrigerator, holding interior components in place.
• Restores a smooth exterior surface and protects internal insulation from moisture and damage.
• Helps maintain proper door alignment and sealing by supporting hinge and trim locations.
• Addresses symptoms such as visible dents, rusted or damaged outer panels, or gaps between panels and trim.

• One outer cabinet housing (quantity: 1), as specified by the OEM part number.

• Disconnect power and remove food from the appliance before beginning work.
• Cabinet replacement may require removal of doors, trim, and internal components.
• Use proper lifting assistance and protective gloves—cabinet panels can be large and have sharp edges.

Replace your microwave's cover panel when the original is cracked, broken, or missing. Restores the appearance and completes the exterior housing.

Controls airflow through your microwave's ventilation system. Installs at exhaust opening to prevent air backflow. Replace if cracked, missing, or damaged.

This is a vent damper door used in the microwave's exhaust system. It opens to allow steam and cooking fumes to vent outside and closes to prevent outside air from flowing back in. Replace this part if the damper is stuck open or closed, if you hear rattling from the vent area, or if you notice poor ventilation or backdrafts during cooking.

Rear wall mounting bracket that securely attaches your microwave to the wall or cabinetry. Replace if your original bracket is missing, cracked, or damaged.

Protective vent grill cover for microwave hoods. Covers and protects the ventilation opening. Replace if cracked, discolored, damaged, or missing.