Parts for Jenn-Air JGRP430WP01: 03 - Oven Parts

This 8-32 x 3/8 screw secures panels, brackets, and internal components in your appliance so everything stays aligned and tight. Replace worn or missing hardware to restore a solid, rattle-free fit and safe operation.

• Fastens components to frames, brackets, or panels
• Helps reduce vibration, rattling, and misalignment
• Replaces missing, stripped, or corroded screws
• Correct 8-32 machine thread for tapped holes in compatible assemblies

• Disconnect power before servicing; shut off gas or water if applicable
• Start threads by hand to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping

Replacement mounting screw for electric wall ovens and ranges. Secures panels, brackets, and trim pieces. Replaces lost, stripped, or damaged screws.

The screw and bumper assembly includes a small cushioning stopper and its mounting screw, designed to prevent hard contact between moving parts or doors and the appliance frame. These bumpers absorb impact and reduce noise when drawers, doors, or panels are opened and closed. Replace this set if you hear loud banging or rattling when operating your appliance or if the existing bumper is worn, torn, or missing.

If your range display blanks out, shows error codes like F8:E0, or doesn't respond to controls, the electronic control board likely failed. Restores normal operation.

This is a clear glass or plastic lens cover that protects the interior oven light bulb from heat, grease, and food splatter. It snaps or screws into place over the light socket inside the oven cavity. Replace this lens if it is cracked, discolored, missing, or if it no longer stays securely in position.

Illuminates oven interior for monitoring food without opening door. Replace when bulb burns out or flickers. High-temperature rated. Verify compatibility.

Illuminates your oven cavity for safe cooking monitoring. Replace when burned out or dim. Confirm fit with your model number before ordering.

Door hinge receiver for wall ovens. Mounts inside the oven frame to hold the door hinge in place. Replace if cracked, deformed, or causing door alignment issues.

Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.

This front frame fin replaces a damaged or worn front frame piece to help keep the dryer drum/tub aligned and reduce rubbing or airflow leaks. It restores the front assembly fit for reliable operation. What it does:

• Supports the front edge of the tub/drum and helps maintain proper drum alignment
• Helps seal and guide airflow at the dryer front to promote efficient air movement
• Reduces rubbing, scraping, or vibration caused by a cracked or warped front frame area
• Resolves symptoms like unusual noise, clothes catching, or uneven drum rotation when damaged

• Disconnect power (and gas if applicable) before starting any repair
• Replacement typically requires removing the dryer front panel or bulkhead; follow your model's service instructions
• Keep all fasteners and seals in place and reassemble securely before testing

The Spark Module is an OEM replacement part for Whirlpool ranges. It is an electrical component that generates the spark needed to ignite the gas burners. By sparking consistently and reliably, the module allows the cooktop burners to ignite with each use. 

Causes of a bad spark module can include normal wear and tear over time, exposure to moisture or residue, or issues with the electronic components that produce the spark.

Symptoms of a bad spark module include:

• Burners that will not ignite or light consistently  
• Burners that ignite but then immediately go out
• Only some of the burners lighting while others do not
• A clicking sound coming from the ignitors but no visible spark

Note: For harness from spark module to igniters use part number 9756892.

This OEM Whirlpool replacement spark module is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Oven won't heat properly or overheats? A faulty temperature sensor may be the cause. Simple 15-minute DIY repair with basic tools and our video guide.

Heating element not working? This mounting screw securely fastens the heating element in place. A simple DIY repair that takes about 20 minutes to complete.

Size: 8-18 x 3/8 inch.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Oven won't heat properly or overheats after self-cleaning? A faulty lower thermostat often causes temperature regulation issues. Moderate DIY repair.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Seals your oven door to prevent heat loss and maintain cooking temperatures. Replace if worn, cracked, or heat escapes. Confirm fit with your model.

Top-mounted broil burner for gas range ovens. Replaces worn, cracked, or damaged burners that no longer provide even heat distribution for broiling.

If your range burner won't light or clicks continuously, the surface igniter may have failed. This part ignites gas at the burner for proper flame.

This bake burner is the oven's gas combustion component that produces the heat for baking and roasting. It restores reliable oven heating so you can cook and bake at the proper temperatures. What it does

• Provides the primary gas flame for the oven's bake function.
• Helps the oven reach and maintain baking temperatures.
• Resolves symptoms like no oven heat, weak or erratic bake flame, or oven not maintaining temperature.
• Works with the oven's ignition system and safety controls to light and sustain the burner.

• One bake burner assembly.

• Turn off gas supply and power to the appliance before beginning any work.
• Inspect ignition and burner ports for debris; clean or replace as needed for proper lighting.
• Follow the oven manufacturer's service instructions and local codes when reconnecting gas lines.

Replacement oven rack support bracket for gas ranges. Installs inside the oven cavity to hold racks in position. Order if your support is bent, broken, or missing.

Fix a range burner that won't light or clicks but doesn't ignite with a new surface ignitor. Simple repair that restores gas burner function quickly.

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

Gas tubing for ranges. Connects gas supply to burners or oven components. Replace if cracked, kinked, damaged, or leaking to restore safe operation.

Gas supply tube connects your range to the gas line. Replace if tube is cracked, kinked, corroded, or leaking. Essential for safe gas flow to burners.

This is a genuine mounting screw used to secure panels, brackets, or components on compatible Whirlpool appliances. It provides a simple, reliable fastening solution for repairs and reassembly. What it does:

• Secures panels, brackets, trim, or component assemblies to prevent movement or rattling
• Restores proper alignment and fit of parts after repair or servicing
• Helps eliminate vibration noise caused by loose fasteners
• Used anywhere the OEM screw specification is required for a reliable fit

• Use the matching driver bit and correct torque to avoid stripping the head or damaging threads
• Replace only with the exact OEM screw to ensure proper fit and function
• Disconnect power to the appliance before accessing internal components