Parts for Viking Range VGRC48: Panel / Oven Assembly Parts

A replacement hinge assembly that secures and guides the appliance door for smooth opening and reliable closure. Restores proper door alignment to reduce sagging, rubbing, and incomplete latching on compatible Viking units. What it does:

• Mounts the door to the cabinet and provides the pivot point for opening and closing.
• Supports door weight to prevent sagging and misalignment over time.
• Helps the door close fully and maintain a proper seal to improve operation.
• Common symptoms this part can fix: door droops, door rubs or binds, uneven closing, or noisy hinge movement.

• Disconnect electrical power (and gas supply where applicable) before beginning any repair.
• Support the door while removing/installing the hinge to prevent dropping or damage; have an assistant if needed.
• Keep all fasteners and small parts; replace damaged hardware with OEM-specified screws if required.
• Follow the OEM service manual or diagram for correct orientation, alignment, and torque.

Restore smooth, controlled movement to your appliance door or lid with this hinge assembly. Replacing a worn hinge corrects sagging, binding, and poor closure so the door aligns and closes properly for reliable everyday use.

• Provides the pivot and support for the door or lid
• Controls opening/closing motion for smooth, consistent operation
• Helps maintain alignment so the door closes flush with the frame
• Common symptoms of a failing hinge: sagging, binding, squeaking/popping, or a door that won't close fully or evenly

• Disconnect power and, shut off gas/water before servicing
• Support the door; mark hinge positions; remove mounting screws carefully
• Transfer any brackets or covers from the original hinge if needed
• After installation, check alignment and closure; adjust per the service manual

This 6" replacement leg restores proper height and stability to compatible ranges and ovens. Heavy-duty metal construction supports appliance weight and helps level units for safe, even cooking. What it does:

• Replaces worn or damaged oven/range leveling legs to restore correct height and stability
• Allows appliance to be leveled to stop rocking or movement on uneven floors
• Helps correct door alignment and seal issues caused by an unlevel unit
• Durable design supports normal appliance weight and everyday use

• Two 6" replacement legs

• Disconnect power and gas (if applicable) before servicing; follow all safety procedures
• Have a second person assist when lifting or tilting the appliance to access legs
• Thread legs in by hand; adjust to level, then snug—do not overtighten or force

This right-hand oven door gasket seals the edge of the oven door to help keep heat and cooking steam inside, restoring a proper door seal for more consistent oven performance. What it does:

• Replaces a worn or damaged right-side door seal to reduce heat loss and prevent smoke or steam from escaping
• Helps the oven maintain set temperatures and even cooking by restoring a tight door seal
• Useful when the door edge looks compressed, torn, or allows light/air to pass
• Reduces cycling from thermostat overcompensation caused by escaping heat

• Disconnect power to the appliance before starting any repair.
• Remove the oven door or open it per the manufacturer's instructions for easier access.
• Clean the gasket channel and mating surfaces before installing the new gasket to ensure a proper seal.
• Inspect mounting area for clips or adhesive; follow OEM guidance for reattachment and ensure the gasket seats evenly around the door.

This replacement oven door gasket seals the oven cavity to retain heat for better cooking performance and lower energy loss. Designed for 30" and 36" ovens, it restores the door seal to reduce heat escape and uneven baking. What it does

• Creates a tight door seal to help keep oven heat inside the cavity
• Reduces heat loss that can cause long preheat times and uneven cooking
• Helps prevent excessive surface heat around the door and nearby cabinetry
• Replaces cracked, flattened, or worn gasket material that no longer seals

• One oven door gasket

• Allow the oven to cool and disconnect power before starting any work
• Remove the old gasket first; most gaskets press or tuck into a channel around the door
• Press the new gasket into the retainer channel evenly, working around the door until fully seated
• Avoid sharp tools that can damage the gasket; check the seal after installing by closing the door and inspecting for gaps

This lower access panel replaces a damaged or missing lower front panel to restore the appliance's appearance and protect components behind the kick/vent area. It provides a finished look and shields wiring and components from debris. What it does:

• Covers and protects the lower front opening of the appliance cabinet
• Restores cosmetic appearance after dents, rust, or missing panel damage
• Helps keep dust, debris and small objects out of the service cavity
• Supports proper airflow routing around lower components when installed correctly

• 1 lower access panel

• Disconnect power to the appliance before beginning any work
• Remove the toe kick or existing panel screws to access the mount points
• Handle edges carefully; wear gloves to avoid cuts from sheet metal
• Use the OEM fasteners and align panel to existing mounting holes for proper fit

This 1/2" x 1/4" rubber bumper cushions contact points to reduce noise and prevent damage on appliance doors, drawers, and panels. It restores proper cushioning for smoother, quieter operation and helps maintain a snug fit. What it does:

• Absorbs shock where panels or doors meet to reduce rattling and clapping noises
• Prevents metal-to-metal contact that can cause chipping, scratching, or wear
• Helps doors and drawers close more evenly by restoring original spacing
• Commonly used where small, press-fit bumpers have worn, flattened, or fallen off

• One 1/2" x 1/4" rubber bumper

• Press-fit replacement; remove old bumper and press new bumper into the same hole until flush
• No special tools required; use a flat pick or small screwdriver to remove old bumper if needed
• Avoid installing on hot surfaces or near heating elements; let appliance cool before service
• Replace matching bumpers in the same area if others show wear for even performance

The Spark Module Wire is an OEM part for Viking ranges and cooktops. It is responsible for transmitting the electrical signal from the spark module to the burner igniters, enabling the burners to ignite when the control knob is turned on. This wire is crucial for the proper functioning of the ignition system, ensuring that the gas ignites quickly and efficiently.

Over time, the spark module wire can become worn or damaged due to heat exposure, accidental pinching during maintenance, or normal wear and tear. When the wire is compromised, it can lead to issues with the burner ignition process, affecting the overall performance of the appliance.

Symptoms of a bad spark module wire include:

• Burners not igniting or taking longer to ignite
• Intermittent sparking or no sparking at all
• Clicking sound without ignition

This OEM part is specifically designed for Viking appliances, ensuring compatibility and reliable performance.