Kenmore Dryer 110.7057700 (1107057700, 110 7057700) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 341241
Get your dryer spinning smoothly again - install the Whirlpool 341241 OEM Drum Belt in minutes.
Why this belt?
- Exact factory spec: 92 ¼-inch length × ¼-inch width, 4 ribs / 3 grooves - built to Whirlpool standards, not a generic copy.
- Broad compatibility: Fits most Whirlpool-made dryers - Kenmore 110-series, Roper, Estate, Maytag, KitchenAid, Admiral, Crosley, Amana & more.
- Quiet, durable rubber: Reinforced EPDM resists cracking and stretch for years of reliable tumbling.
Fixes these common dryer problems
| Problem |
How the belt solves it |
| Drum won’t turn |
Transfers motor rotation to drum |
| Loud squealing / thumping |
Replaces stretched or frayed belt |
| Burning-rubber smell |
New belt stops slippage & heat build-up |
| Damp clothes / long cycles |
Restores correct drum speed & airflow |
DIY install — about 15 minutes
- Unplug dryer; remove lint screen housing & front panel.
- Release belt tension at idler pulley; lift drum slightly to slide old belt off.
- Loop new belt around drum, idler pulley and motor pulley (ribbed side down).
- Re-assemble, run test cycle - enjoy quiet, consistent tumbling.
This part fixes the following symptoms
-
Heat stays on after drum has stopped
-
Will not tumble
-
Touchpad does not respond
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Broken dryer belt Bob B. • St Louis , MO • September 12, 2015
Unpluged dryer first. Then took the lint filter out and removed the two philips screws inside the lint filter lid. Then take a paint scraper just under the top of the dryer two inches from the left front corner and pushed in a little to release the snap connector and did the same on the right side. Then lifted top over. Then take a 5/16 socket or nut driver and remove the two screws on on the left inside panel, then the right side. Lean front out a little and remove the two wires one the back...
Read more
More
$14.64
- Compare At:
-
$17.42
- You Save:
-
$2.78
Genuine Whirlpool part
By: Whirlpool
Part Number: 349241T
The Dryer Rear Drum Support Roller Kit is an OEM replacement part for Whirlpool dryers, as well as Kenmore, Samsung and other brands. This kit includes the rear support rollers that are crucial for maintaining proper drum alignment and smooth rotation during the drying cycle. Matching belt 341241 and idler pulley WP691366.
Symptoms of a faulty Rear Drum Support Roller Kit include:
- Excessive vibration or shaking during drying cycles
- Loud grinding or squeaking noises from the rear of the dryer
- Uneven wear or visible damage to the rollers
- Potential drum misalignment, rubbing against the drum casing, or leaks
Causes of a bad Rear Drum Support Roller Kit can include wear and tear over time, excessive load imbalances, or physical damage from impact or mishandling.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryer models.
Do-It-Yourself Stories from Customers like You
Thumping/vibrating/rattling pretty bad fixed 100%! Doug P. • Durham , NC • November 15, 2015
I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a...
Read more
More
$17.74
- Compare At:
-
$21.29
- You Save:
-
$3.55
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691366
The Idler Pulley is an OEM part for Whirlpool dryers, responsible for maintaining the correct tension on the drive belt, allowing it to remain tight and aligned, preventing slipping and contributing to the consistent rotation of the drum during cycles.
Symptoms of a bad Idler Pulley include:
- Squealing or squeaking noises
- The dryer drum failing to turn
- Excessive vibration or unusual sounds
Causes of failure can range from normal wear and tear, which can lead to the pulley's bearing wearing out, to the accumulation of lint and debris causing the pulley to seize or function improperly. Additionally, a cracked or damaged pulley can lead to belt misalignment and slippage.
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Fits all Whirlpool-made dryers (Whirlpool, Kenmore with prefix 110, Roper, KitchenAid, and Estate). Matching belt 341241 and rear support rollers 349241T. Whirlpool dryer repair manual 677818L.
This part fixes the following symptoms
-
Will not tumble
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Thumping/vibrating/rattling pretty bad fixed 100%! Doug P. • Durham , NC • November 15, 2015
I am very glad to find the AppliancePartsPros.com website! Their instructional videos and easy parts reference made all the difference. I had originally planned to have someone come to fix my dryer, but no one was available for at least a week. I checked out their site, and after watching the videos I felt confident I could repair my appliance. I determined that a drum roller wheel had gone bad. Apparently it was going bad over the last five years since the dryer always seemed to rattle a...
Read more
More
$15.65
- Compare At:
-
$18.78
- You Save:
-
$3.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 8009
Original Whirlpool light bulb, 40 watt.
Symptoms of needing to replace the light bulb include:
- Dimming or flickering light
- Complete lack of illumination inside the appliance
- Visible signs of damage or burnout on the bulb itself
Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.
Do-It-Yourself Stories from Customers like You
Jennair jjw9630cas double oven doors did not close all the way and the light would not go out Wayne W. • East Longmeadow , MA • February 13, 2016
I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it...
Read more
More
$17.76
- Compare At:
-
$20.96
- You Save:
-
$3.20
Genuine Whirlpool part
By: Whirlpool
Part Number: 279827
The Dryer Drive Motor is an OEM part for Whirlpool dryers. This motor is the heart of the dryer, responsible for turning the drum and enabling the air to circulate properly throughout the machine.
Over time, dryer motors can suffer from wear and tear due to continuous use, accumulation of lint and debris, or overload from heavy laundry loads. These factors can lead to the motor overheating, losing power, or failing to start altogether.
Symptoms of a bad Dryer Drive Motor include:
- The dryer not starting when the start button is pressed
- Unusual noises, such as humming or buzzing
- The dryer stopping unexpectedly during cycles
- A burning smell coming from the dryer
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
This part fixes the following symptoms
-
Will not tumble
-
Noisy
-
Shuts off too soon
See more...
Do-It-Yourself Stories from Customers like You
High pitched squeal: maybe a roller wheel maybe a bad felt bearing on drum maybe a rubbing fan wheel or just a burned out motor! Bruce K. • Pikeville , KY • September 06, 2014
My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping.
My thing was:
I would turn it off and turn the drum by hand about halfway around and it would work again.
Last month, my wife said it stopped again and its making a loud noise,
but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse).
I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,...
Read more
More
$97.95
- Compare At:
-
$131.61
- You Save:
-
$33.66
Genuine Whirlpool part
By: Whirlpool
Part Number: 279570
The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.
Symptoms of needing to replace the door latch kit include:
- Difficulty in closing or latching the washer door
- Door opening unexpectedly during the wash cycle
- Leaks or water seeping due to an improper door seal
- Excessive wear or damage to the latch components
Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.
This part fixes the following symptoms
-
Door won't close
-
Shuts off too soon
-
Doesn't shut off
-
Takes too long to dry
See more...
Do-It-Yourself Stories from Customers like You
Dryer door latch worn out Kathy M. • San Diego , CA • February 22, 2015
When I looked up the part number there was a handy video that popped up. I watched the video and thought "how easy!" so, I ordered that part and waited. The next day, I thought I better start to take the door off of my dryer (because that's what the video instructed, and I wanted a head start) so as I was going into the garage to get my tools, my son came in with a small package. It was the part. That came, to quote another customer, "Crazy Fast!" All the way from Kentucky to California! ...
Read more
More
$6.95
- Compare At:
-
$13.85
- You Save:
-
$6.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10512946
The Drum Support Wheel Retainer is an OEM part for Whirlpool dryers. This part secures the drum support wheels in place, ensuring that the dryer drum rotates smoothly and quietly during operation. The retainer is designed to fit precisely, preventing the support wheels from loosening or wobbling, which can lead to inefficient drying and increased wear on other components.
Over time, retainers can wear out or become damaged, potentially leading to a loose drum support wheel. This can cause the dryer to operate noisily, vibrate excessively, or even damage the drum itself if not addressed promptly.
Symptoms of a bad Drum Support Wheel Retainer include:
- Unusual noises, such as squeaking or thumping, coming from the dryer
- Excessive vibration during operation
- The dryer drum may feel unstable or wobble when turned by hand
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
My whirlpool duet dryer started to squeal and rumble when the dryer was on Diana K. • Phoenix , AZ • September 20, 2014
I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig!
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694089
The Blower Wheel is an OEM part for Whirlpool dryers. This component is crucial for the proper circulation of hot air within the dryer drum, ensuring efficient drying of clothes by directing airflow through the drum and out the exhaust.
Common causes of a bad blower wheel include accumulated lint and debris obstructing the wheel, physical damage from foreign objects, or general wear from prolonged use. A faulty blower wheel can significantly reduce drying efficiency and may cause the dryer to overheat.
Symptoms of a bad blower wheel include:
- Longer drying times for clothes
- Unusual noises during the drying cycle
- Overheating of the dryer
- Poor airflow from the dryer vent
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not tumble
-
Takes too long to dry
-
Noisy
See more...
Do-It-Yourself Stories from Customers like You
Broken blower wheel on dryer Mark B. • Independence , WV • April 12, 2014
I FOUND the website on t internet, found my part ordered it and watched the how to video ,repaired the dryer myself. Awesome Website.
Read more
More
$33.48
- Compare At:
-
$39.84
- You Save:
-
$6.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP339956
The Lint Screen Housing Foam Seal is an OEM part for Whirlpool dryers. This seal is placed around the lint screen housing to prevent air leaks and ensure that the dryer operates efficiently by directing airflow properly through the lint screen. By maintaining a tight seal, this foam helps to optimize the dryer’s performance, reduce drying times, and prevent lint from escaping into the internal parts of the dryer, which can lead to potential maintenance issues and decreased efficiency.
Symptoms of a failing lint screen housing foam seal include:
- Increased lint buildup inside the dryer beyond the lint screen
- Longer drying times due to inefficient air circulation
- Excessive heat and humidity within the dryer
Causes of foam seal deterioration typically involve normal wear and tear, exposure to high heat which can degrade the material, or improper maintenance that can tear or dislodge the foam.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Takes too long to dry
-
No heat or not enough heat
See more...
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$10.43
- Compare At:
-
$12.41
- You Save:
-
$1.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10359270
The Drum Support Roller Shaft - Left is an OEM part for Whirlpool dryers. It is specifically designed to support the drum roller, ensuring smooth rotation of the dryer drum during operation. This shaft is essential for maintaining the drum's alignment and stability, allowing for effective and efficient drying of clothes.
Causes of a bad drum support roller shaft can include wear and tear from regular use, accumulation of lint and debris, or damage from overloading the dryer. These factors can lead to the shaft becoming worn out or bent, impairing the dryer’s performance.
Symptoms of a bad drum support roller shaft include:
- Squeaking or grinding noises during the drying cycle
- The dryer drum not rotating smoothly or being off-balance
- Increased drying times or incomplete drying of clothes
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Old appliance with worn drum roller shafts and rollers Macario M. • Kingsville , TX • December 17, 2021
Use the videos on this website here and you can repair most brands. Many are duplicate in design.
1. Unplug the machine.
2. Move it away from a confined area to get more room.
3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet.
4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you...
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Whirlpool part
By: Whirlpool
Part Number: W11415783
The Seal is an OEM part for Whirlpool dryers. This specific seal is designed to fit around the blower housing, ensuring a tight seal that prevents air leaks within the dryer. The blower housing is a critical component of the dryer's air circulation system, which moves air through the drum to dry clothes efficiently.
Causes of damage to the Seal can include wear and tear from regular use, excessive heat degrading the material over time, or improper maintenance practices that can cause physical damage to the seal.
Symptoms of a bad Seal include:
- Longer drying times than usual
- Excessive heat buildup in the dryer
- Unusual noises from the dryer, such as rattling or buzzing
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Gas dryer did not heat and excessive lint inside the unit James C. • New Boston , MI • July 20, 2017
Our 19 year old Whirlpool dryer quit heating. After checking the thermal fuse, I found the ignitor electrically open. I bought an ignitor at a local store as there was a national holiday the next day and I did not want the dryer inoperative waiting several days for shipping. I can say AppliancePartsPros is MUCH cheaper for the identical Whirlpool genuine part. While changing the ignitor, I noticed there was an excessive amount of lint in the dryer, which was caused by worn drum seals. I ordered...
Read more
More
$16.75
- Compare At:
-
$19.93
- You Save:
-
$3.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10359269
The Drum Support Roller Shaft - Right is an OEM part for Whirlpool dryers. This shaft provides support for the drum roller, allowing the dryer drum to rotate smoothly and efficiently during drying cycles.
You should replace the drum support roller shaft if it becomes worn, bent, or damaged. Causes of a bad drum support roller shaft can include regular wear and tear, overloading the dryer, or exposure to high temperatures, which can affect its structural integrity.
Symptoms of a bad drum support roller shaft include:
- Unusual noises such as squeaking or grinding during operation
- The dryer drum not rotating smoothly or becoming stuck
- Excessive vibration or wobbling of the dryer drum
- Visible wear or damage on the roller shaft
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Old appliance with worn drum roller shafts and rollers Macario M. • Kingsville , TX • December 17, 2021
Use the videos on this website here and you can repair most brands. Many are duplicate in design.
1. Unplug the machine.
2. Move it away from a confined area to get more room.
3. Remove lint filter and the two screws that hold the exhaust filter port to the top of the cabinet.
4. Use a putty knife or actually a butter knife and release the top of the cabinet from the main drum housing. You will slide the knife between the top and the main cabinet at the plastic catches. Look for them and you...
Read more
More
$48.95
- Compare At:
-
$58.25
- You Save:
-
$9.30
Genuine Whirlpool part
By: Whirlpool
Part Number: 239087
The Rear Dryer Drum Felt Seal with Adhesive is an OEM part for Whirlpool dryers. It forms a protective barrier along the rear opening of the dryer drum, preventing air leaks and absorbing sound-dampening vibrations.
Causes of a bad rear drum felt seal can include degradation of adhesives from heat cycling or poor drum surface bonding from bending stresses over time.
Symptoms of a bad rear dryer drum felt seal include:
- Reduced drying effectiveness and longer cycle times from air leaks
- Excessive noise emanating from around the rear drum seal area
- Flapping or loose seals allow air pathways to form
- Deterioration of the felt allowing lint and dust collection behind
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016
After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify...
Read more
More
$41.95
- Compare At:
-
$58.24
- You Save:
-
$16.29
Genuine Whirlpool part
By: Whirlpool
Part Number: WP691581
The Door Switch Lever is an OEM part for Whirlpool dryers. It plays a vital role in ensuring the dryer only operates when the door is securely closed by engaging with the door switch to signal the door's status.
Causes of a bad door switch lever can include normal wear and tear from repeated use, physical damage from accidental impact, or deformation from heat and humidity inside the dryer. A faulty lever can prevent the dryer from starting or stopping correctly.
Symptoms of a bad door switch lever include:
- Dryer not starting
- Dryer stopping mid-cycle
- Door not latching properly
- The dryer continuing to run with the door open
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Won't start
-
Doesn't shut off
See more...
Do-It-Yourself Stories from Customers like You
The lever to the door switch broke. Valerie M. • Rochester , NH • April 02, 2014
First, I rooked on YouTube for a video on how to fix it. The video brought me to a very helpful video with a link to your website. We have had this dryer since we bought the house 10 years ago and the thought of buying something new, that wasn't made as well was a dreaded thought. I went on the website, entered the model number of my dryer and then a search link for a parts search. Not knowing the part number, I was able to find the exact thing I needed. It was amazing and so easy! Had...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP18776
The Top Lock is an OEM component for Whirlpool electric and gas dryers. It secures the outer metal cabinet door during drying cycles for safety and ventilation. This lock provides a method for releasing and latching the door tightly when shut.
Symptoms of a failing top lock may include:
- Inability to fully close or properly latch the dryer door
- Accidental opening from deficient locking during operation
- Difficulty manipulating the lock due to worn or broken parts
Causes related to normal wear of moving parts through frequent use over several years. Deformation from excessive exterior impacts could also damage locking mechanisms.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Multiple problems warn parts Jeffrey C. • Severna Park , MD • April 29, 2015
Excellent! Repairs went as planned. Diagnosed problem parts on my dryer; ordered parts online thru Appliance Parts Pros; parts arrived very quick - standard ground - and parts shipped as ordered with no mistakes. Plus, they sent me a Wine voucher (my order was nearly $200). And, if you have trouble troubleshooting your appliance problem or figuring out how a part is supposed to be installed on your appliance, Appliance Parts Pros has an excellent video library to help you!
I will certainly...
Read more
More
$12.51
- Compare At:
-
$14.76
- You Save:
-
$2.25
Genuine Whirlpool part
By: Whirlpool
Part Number: 279264
The Front Bearing and Seal Kit is an OEM replacement part for Whirlpool dryers. This kit includes the front bearing and seal for the dryer drum, which work together to provide smooth operation and prevent premature wear.
Causes of a bad front bearing and seal can include regular wear and tear from normal use, heavy loads that place extra strain on the bearings, or debris accumulation causing increased friction.
Symptoms of issues include:
- Noisy or grinding sounds coming from the drum area
- Vibration noticed during the operation
- Difficulty turning or rotating the dryer drum by hand
- Reduced efficiency and longer drying times
This OEM replacement kit is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Noisy & inefficient Richard M. • Indianapolis , IN • December 06, 2016
After having replaced the drum support rollers twice in a roughly 3yr period, I realized something wasn't quite right, and indeed it wasn't. I had been ordering the wrong parts - I did use the online parts locator after checking, & double checking my model number. Apparently my older Whirlpool dryer has a somewhat ambiguous model number because the rollers that were shipped each time looked nothing like the originals. I realize that is not particularily uncommon - manufacturers often modify...
Read more
More
$59.95
- Compare At:
-
$71.34
- You Save:
-
$11.39