Kenmore Dishwasher 665.74363K2 (66574363K2, 665 74363K2) Parts

My discharge would not empty after a wash cycle and I always had gross gray water left in the bottom approx 3" deep? After doing the obvious things of checking the simp for garbage, and checking that the discharge hose wasn't blocked, I removed my discharge pump ( not too hard to do) and tested. My pump which did run and turn the impeller. However, the pump evidently had weakened with time and weakened and could no longer pump the waste water up hill to the "T" connection under the sink. A... Read more

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

Purchased a replacement basket. First I visited the Sears website for a replacement part since the dishwasher was a Kenmore, but Sears did not carry the same basket that was original to the dishwasher. Their replacement was an open basket without dividers. You are the only company that I found that carries the exact part for the model of dishwasher. An vanother pleasing experience I had with AppliancePartsPros.com is that I received the replacement within 5 days of placing the order. It... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

• Not drying dishes properly

Replaced heater element: Once I had the dishwasher out of the cabinet with supply hose, drain hose and electric disconnected, removing the heater element was fast and easy. However, it was confusing that the new heater element had rubber washers on it already, something not mentioned in the product listing, although kinda visible in the photo. I ordered the separate rubber washer parts recommended by Appliance Parts Pros together with the heater element. The separate rubber washers were the... Read more

• Noisy
• Will not drain

I had previously disassemble the pump assembly to find what I at first thought was an oddly shaped spring, which it was. What I learned by researching the parts was that the spring's odd shape was a result of something having gotten caught in the pump and jamming the impeller. After ordering the parts, I watched the "repair video" a few time and proceeded to remove and replaced the affected parts. Reassembly went pretty much as described with the one small glitch being the seating of the new... Read more

Replaced upper and lower spray arms, plus nylon bearings. Read more

• Not cleaning dishes properly

Replaced upper and lower spray arms, plus nylon bearings. Read more

• Won't start

My friend researched online what would make a dishwasher just stop working, no power. The person on the you tube video showed how to first start with the thermal fuse. Then searched online for the thermal fuse. You had the part for a small price. I felt it was worth trying to see if that may be the issue. IT WORKED!! I was without a dishwasher for over a year, was planning to by a brand new one but for $23.00 now have a working dishwasher!! YEAH! Read more

Removed 8 hex screws and the cap to remove the broken threads...used needle nosed pliers for this, stuck them in and expanded them to put pressure on the thread sleeve from the inside, as threads were broken off below the edge. Replaced all very simply Read more

Snaped off and snaped on. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

Replaced It With New One Read more

Touch up paint Read more