Kenmore Range 665.78003802 (66578003802, 665 78003802) Parts

On my Jenn-Air downdraft range, the oven stopped heating. The broiler still worked. So pulled the pan off the bottom so I could see and found the igniter wasn't glowing to start the gas. I had replaced the full electronic control panel using Appliance Parts Pros so knew they had the full breakdown of parts for my model. I found the igniter and ordered. But frankly, I wasn't sure about doing the repair myself. It looked easy enough from videos and discussions here. Still, dealing with the... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more

Took the stove apart*, saw where the mouse had made a nest. It was kind of like a hotel room after a rock star had used it. It was nasty, is what I'm saying. I removed the insulation, which immediately went into a garbage bag and was placed outside, whereupon I took off and nuked the site from orbit. It was the only way to be sure (actually it was disposed of in the proper manner, no nukes were detonated in the course of this repair). Anyway, I ordered the insulation from this site, which was... Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

I have tried to remove the burner assemblies by removing the torx screws but they were badly rusted, and unfortunately they all were broken during removal. I just discarded the ruined orifices and assembled the new orifices and burner assembly. Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

Replaced It With New One Read more

Touch up paint Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

Replaced old igniter. also purchased new screws for burner and igniter assembly since old screws were corroded from spilled food/fluids etc over the years. made the installation much easier. If you need to replace a worn igniter, do yourself a favor and go to hardware store and get matching replacement screws or buy new with igniter. Now my front right burner lights every time with just a click or two. Very pleased. Read more

The lightbulbs were a problem for me as I did not know if they were 12 V or 120 V. But the interactive parts diagram on the website was very helpful and allowed me to order the correct bulbs very rapidly(120V is correct). They were very easy to change out except for the fact that I needed to have my 12-year-old son do part of it since his hands are smaller than mine.(and it is always good for sons to work with dads even on small projects like this.) The cooking element was also amazingly easy... Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more