Kenmore Refrigerator 106.51189110 (10651189110, 106 51189110) Parts

Found the parts in the diagram of my fridge and simply installed it very easy Read more

Remove and replaced the auger motor, shaft seal, and the chute seal. No problem. However, the causing failure was to broken wire on the bottom of the freezer door. Loom and blue wire were cut, due to being pinched. I had current to start with and the auger worked three times then quit. That's when I really had to start searching . Fun. Read more

Bought new optic control boards, both the emitter and the receiver. The repair process was so simple. The KitchenAid repair tech came out to diagnose our issue. He was only going to come back and install a new emitter. They wanted a lot of money to do the repair. They were going to charge us $257 just for the part (emitter board). We bought both boards for $300 from AppliancePartsPros. We decided to replace both boards, because if one went bad the other might not be far behind. Read more

Simple Repair. Read more

Replaced the auger motor. Read more

• Leaking

Thought leak was coming from icemaker but refrigerator was making ice just fine. had puddle on floor just below freezer door. upon closer inspection realized leak was coming from drain line. there were 2 pieces of tubing and the connector. leak was coming from where tubing goes into connector. wanted to replace it. didn't know what it was called. did live chat with someone I think was named James. he sent me diagrams and I could identify the part. once identified I ordered it. boom.... Read more

Easy fix. Took two screws out of top door hinge. Lifted door off of bottom hinge. Laid door on blanket on floor. One cam part went on the hinge that was on the fridge, snapped in place. One cam part went on bottom of door, one screw to replace. Replaced door on bottom hinge then put top hinge back on. Job done. Read more

I ordered the parts from you guys and printed the diagrams you had available. With that the repairs took less than 30 minutes. Read more

I put all pieces that I ordered on the dryer and plugged it in. Read more

Replaced hoses. They were not an exact replacement but they did end up working with the purchase of one additional fitting (5/16 x 1/4 coupler) Read more

I purchased replacement parts to completely replace basket, face plate, and rollers. I received exactly what I ordered. The only problem I had was removing the part(s) from the shipping box. I thought the part came assembled (as rollers had been installed onto the basket), but the face plate had not been snapped into place. When I removed everything from the shipping box as one piece, the face plate fell off, hit the tile floor, and cracked. Bummer. Since the original face plate was in good... Read more

My LG electric dryer stopped drying the other day and I searched on line for suggestions on what may have caused it to stop working. I came across AppliancePartsPros.com and quickly found some of the most common issues with my LG dryer. The problems were listed in the order of most common occurrence, and had extremely helpful and detailed instructions on how to not only diagnose the problem, they also showed exactly how to access and repair the issue. Unfortunately, it was late on a Thursday... Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

Rather than fighting the set screw, I ordered a new handle and extra parts to fix it. My father taught me to use anti seize which I used on all the threaded materials. Appliance parts and all the parts listed easy to see and Order Read more

Water line coming out of inlet valve to ice maker was cracked. Removed the paperboard cover from the bottom of the back of the fridge, then unplugged the water line going from the inlet valve to the ice maker. Wasn't sure this new tube was going to work, because the original had an elbow on it. Fit just fine. Removed grille from front and disconnected other end of ice maker water line. Attached new line and now I have ice! Read more