Kenmore Refrigerator 106.52562100 (10652562100, 106 52562100) Parts

Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.

This icemaker mounting bracket secures the ice maker to the freezer wall, keeping the assembly level and correctly aligned with the fill tube. Replacing a bent or broken bracket helps restore stable ice production and reduces rattling or leaks.

• Supports and stabilizes the ice maker assembly inside the freezer
• Maintains proper alignment with the fill tube and ejector mechanism
• Helps prevent vibration, rattling, and water overspray that can cause ice clumps or cubes missing the bin
• Common signs include a loose or sagging ice maker, crooked alignment, noise during harvest, or water/ice buildup near the fill area

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin and ice maker to access; transfer and reuse existing screws to install the new bracket in the factory holes
• Level the ice maker and confirm fill-tube alignment before tightening fasteners
• Restore power and water; check for leaks and normal ice production

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

Used to prevent water from overflowing from the dispenser on the freezer door. Color: Biscuit. It measures about 10 inches wide by 3 inches deep. For black order WP2206670B. For white order WP2206670W.

This evaporator fan motor circulates air across the freezer's evaporator coils and throughout the cabinet. Replacing a worn or stalled motor restores proper airflow for even cooling and helps reduce warm spots and frost buildup. What it does:

• Drives the evaporator fan blade to move cold air over the coils and into both compartments
• Helps maintain stable, even temperatures and consistent airflow
• Typical symptoms: weak or no airflow from vents, refrigerator warmer than normal, unusual squealing/rattling from the freezer area, or the fan not running
• Often runs only with the door switch depressed—useful for diagnosis

• Evaporator fan motor

• Disconnect power before servicing; panels and coil fins can be sharp—wear cut-resistant gloves
• Access from the freezer: remove shelves/ice bin and rear panel to reach the motor
• Transfer the fan blade and any mounting hardware from the original motor
• Reconnect wiring, ensure the blade spins freely, and test operation with the door switch before reassembly

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

This bin button is a small snap-in component used on refrigerator storage bins. It helps secure and align the bin so it seats properly and operates smoothly, restoring a tight fit when the original button is cracked, worn, or missing.

• Snaps into a designated opening on the bin or cabinet liner to act as a support/stop
• Keeps the bin aligned and secured during everyday use
• Replaces a damaged or missing button that can cause wobble, binding, or the bin to fall out
• Restores proper fit and smooth operation of the affected bin

• Disconnect power and remove items from the affected bin
• Remove the bin; pry out the damaged/missing button from its seat
• Align and press the new button fully into the opening until secure
• Reinstall the bin and check for smooth, secure operation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

Pan-head screw used to secure panels, brackets and trim on Whirlpool appliances. Replacing a damaged or missing screw restores proper fastening to reduce vibration and keep assemblies aligned during operation. What it does:

• Secures panels, brackets and trim pieces to the appliance chassis.
• Stops loose panels from rattling, vibrating or shifting during use.
• Used when the original screw is stripped, corroded or missing.
• OEM replacement that restores the original fastening point.

• Unplug the appliance or shut off power before working on it.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten or force in plastic parts.
• If the original hole or threads are damaged, inspect the surrounding area before reuse.

Located inside the freezer's ice bucket, this ice auger is the helical shaft that rotates to move cubes toward the chute for cubed or crushed ice. Replacing a worn or bent auger restores dispensing and helps prevent jams and grinding.

• Rotates with the dispenser motor to move ice through the bucket and into the chute
• Works with the crusher assembly to provide cubed or crushed ice
• Damage or wear can cause jamming, slow/weak dispensing, or loud grinding during dispense
• Often replaced when the dispenser motor runs but little or no ice is dispensed

• Disconnect power to the refrigerator; remove the ice bucket from the freezer
• Disassemble the bucket/crusher housing; transfer blades, spacers, and hardware to the new auger in the same order and orientation
• Handle sharp metal parts with care; wear cut-resistant gloves
• Reinstall the bucket fully seated; restore power and test both cubed and crushed functions

This trivet shelf is the shelf insert that adds a usable storage level inside the compartment. Replace a missing or damaged shelf to restore organization and keep items off the liner surface for better use of space.

• Provides stable support for food packages and containers
• Rests on existing side supports or brackets inside the compartment
• Replace when the original shelf is missing, bent, broken, or won't sit level
• Restores the intended storage layout and airflow

• Clear the area by removing or shifting nearby items
• Align the shelf with the side supports and seat both sides fully before loading
• Wear gloves and avoid forcing the shelf into place
• Confirm the shelf sits level and is secure before use

This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.

• Fastens brackets, panels, ducts, or housings to the cabinet or frame
• Replaces missing, stripped, or corroded hardware
• Helps stop rattles, vibration, and loose or misaligned parts
• Maintains proper alignment for reliable operation

• Disconnect power; shut off gas and water before servicing
• Match this screw to the original location and hardware type used on your model
• Start threads by hand to avoid cross-threading; use the correct driver
• Snug only—do not overtighten, especially into plastic or thin sheet metal

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This emitter cover is the molded housing that shields and positions the infrared emitter for the refrigerator's ice level optics. Replacing a cracked or missing cover helps protect the board and keep the beam path clear for reliable ice making. What it does:

• Shields the emitter board and lens from moisture, frost, and debris
• Aligns the infrared beam path across the ice bin to the receiver
• Helps secure and position the ice level optics assembly
• Common symptoms: broken/missing cover, intermittent or no ice production due to optics misalignment or obstruction

• 1 emitter cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the optics components
• Release the old cover's retaining tabs or fastener and lift it off; avoid touching board components
• Position and secure the new cover, then restore power and test ice maker operation

This flat spacer installs on the refrigerator or freezer door hinge. It sets the correct clearance and height between the hinge and door so the door swings smoothly and seals properly. Replace worn or missing spacers to restore alignment. What it does:

• Maintains proper spacing between the hinge and door
• Helps keep the door level and aligned for a consistent seal
• Reduces rubbing or binding as the door opens and closes
• Typical symptoms when worn or missing: door sits low/uneven, rubs the cabinet, won't close reliably, or shows gaps/condensation at the gasket

• 1 flat spacer

• Disconnect power and remove items from the door to reduce weight
• Support the door before removing hinge fasteners; lift the door slightly as needed
• Install the new spacer in the same position/order as the original spacers and washers
• Reinstall and tighten the hinge; readjust if necessary