Kenmore Refrigerator 106.55604400 (10655604400, 106 55604400) Parts

This large refrigerator door shelf retainer bar secures items on the door shelf, keeping jars and bottles from sliding out during everyday use. Replace a broken or missing bar to restore safe, reliable door storage.

• Holds contents on the refrigerator door shelf; stabilizes items when the door opens or closes
• Replace when the bar is cracked, warped, or missing
• Common symptoms: items fall from the door shelf, bar won't stay attached, loose fit
• For the refrigerator compartment door in the large position

• Remove items from the affected shelf; allow cold plastic to warm to room temperature before handling
• Release the old bar from the endcaps or slots and inspect mounting points for damage
• Align and snap the new bar fully into both ends; verify a secure fit before reloading
• No power is typically required; wear gloves and avoid excessive force to prevent cracking

This evaporator fan motor circulates cold air across the evaporator and throughout the compartments for even cooling. Replacing a worn motor restores proper airflow, temperature consistency, and overall defrost performance.

• Circulates air over the evaporator coils and through the vents to cool both compartments
• Helps maintain stable temperatures and supports effective defrost
• Failure symptoms include weak/no airflow, warming in one or both sections, frost buildup on the evaporator cover, or loud/intermittent fan noise
• Motor may start or may run intermittently, causing long run times

• Disconnect power before servicing; internal panels and fan blades can be sharp
• Access the motor behind the freezer's rear panel; remove shelves/ice maker as needed
• Transfer the original fan blade and any mounts/grommets to the new motor; match blade orientation
• Route wiring as original, secure the motor, and ensure the fan spins freely before reassembly

Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.

This icemaker mounting bracket secures the ice maker to the freezer wall, keeping the assembly level and correctly aligned with the fill tube. Replacing a bent or broken bracket helps restore stable ice production and reduces rattling or leaks.

• Supports and stabilizes the ice maker assembly inside the freezer
• Maintains proper alignment with the fill tube and ejector mechanism
• Helps prevent vibration, rattling, and water overspray that can cause ice clumps or cubes missing the bin
• Common signs include a loose or sagging ice maker, crooked alignment, noise during harvest, or water/ice buildup near the fill area

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the ice bin and ice maker to access; transfer and reuse existing screws to install the new bracket in the factory holes
• Level the ice maker and confirm fill-tube alignment before tightening fasteners
• Restore power and water; check for leaks and normal ice production

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

This replacement screw secures panels, brackets, and internal components within your appliance. Replacing a missing or damaged fastener restores a tight fit, reduces vibration and noise, and helps keep parts properly aligned during operation.

• Fastens panels, trim, brackets, or internal components to the chassis
• Maintains proper alignment and stability during normal use
• Replaces missing, rusted, or stripped hardware
• Common symptoms: loose or rattling panels, vibration, difficulty fastening, or a visibly missing screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Match length and thread to the original; replace one-for-one in the same location
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is stripped, repair threads or replace the clip/nut before installing

This water dispenser lever is the paddle you press on your refrigerator's dispenser. Replacing a worn paddle restores smooth activation of the water dispenser and refreshes the look of the dispenser area with a matching Biscuit finish.

• Provides the paddle you press to activate the water dispenser
• Transfers your push to the internal dispenser switch to start water flow
• Common symptoms of a failed lever: cracked/broken paddle, sticking or loose action, or no water dispensing when pressed
• Biscuit color for a seamless, factory-matched appearance

• Disconnect power and shut off the water supply before servicing
• Remove the dispenser front panel/trim to access and release the lever
• Transfer existing pivot hardware or springs from the original lever, if applicable
• Reassemble, restore power/water, and test for smooth operation

This bin button is a small snap-in component used on refrigerator storage bins. It helps secure and align the bin so it seats properly and operates smoothly, restoring a tight fit when the original button is cracked, worn, or missing.

• Snaps into a designated opening on the bin or cabinet liner to act as a support/stop
• Keeps the bin aligned and secured during everyday use
• Replaces a damaged or missing button that can cause wobble, binding, or the bin to fall out
• Restores proper fit and smooth operation of the affected bin

• Disconnect power and remove items from the affected bin
• Remove the bin; pry out the damaged/missing button from its seat
• Align and press the new button fully into the opening until secure
• Reinstall the bin and check for smooth, secure operation

This refrigerator ice auger sits inside the ice bin and rotates to move cubes or crushed ice toward the chute. Replacing a worn, bent, or stripped auger restores smooth, consistent dispensing performance. What it does:

• Rotates inside the ice bin to feed ice toward the crusher and dispenser chute
• Helps deliver either cubes or crushed ice depending on the selector
• Common symptoms: dispenser motor runs but no ice comes out, weak/intermittent dispensing, frequent ice jams, or grinding noises from the ice bucket

• 1 ice auger

• Unplug the refrigerator before servicing; remove and empty the ice bin
• Note the order of internal parts during disassembly; transfer any reusable hardware from the original assembly
• Wear cut-resistant gloves—metal and plastic edges can be sharp
• Reassemble so the auger turns freely by hand, reinstall the bin, restore power, and test the dispenser

This water tube bracket secures the refrigerator's water supply tube along the cabinet or door route. Replacing a damaged bracket helps prevent kinks and leaks and maintains reliable water flow to the dispenser and icemaker.

• Holds and guides the water tube so it stays correctly positioned
• Helps prevent kinks, rubbing, and vibration that can lead to leaks
• Supports consistent water flow to the dispenser and icemaker
• Typical signs of failure: cracked or missing bracket, tube slipping or dangling, recurring kinks, dampness/leaks along the tubing path

• Unplug the refrigerator and shut off the water supply before servicing
• Access the bracket location (often in a hinge or cabinet routing area; varies by model)
• Release the tube, remove the old bracket, and install the new bracket; reuse existing hardware
• Restore water and power, purge air from the line, and check for leaks and dispenser/ice operation

Pan-head screw used to secure panels, brackets and trim on Whirlpool appliances. Replacing a damaged or missing screw restores proper fastening to reduce vibration and keep assemblies aligned during operation. What it does:

• Secures panels, brackets and trim pieces to the appliance chassis.
• Stops loose panels from rattling, vibrating or shifting during use.
• Used when the original screw is stripped, corroded or missing.
• OEM replacement that restores the original fastening point.

• Unplug the appliance or shut off power before working on it.
• Use the correct screwdriver or bit to avoid stripping the head.
• Tighten until snug—do not overtighten or force in plastic parts.
• If the original hole or threads are damaged, inspect the surrounding area before reuse.

This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.

• Fastens brackets, panels, ducts, or housings to the cabinet or frame
• Replaces missing, stripped, or corroded hardware
• Helps stop rattles, vibration, and loose or misaligned parts
• Maintains proper alignment for reliable operation

• Disconnect power; shut off gas and water before servicing
• Match this screw to the original location and hardware type used on your model
• Start threads by hand to avoid cross-threading; use the correct driver
• Snug only—do not overtighten, especially into plastic or thin sheet metal

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This emitter cover is the molded housing that shields and positions the infrared emitter for the refrigerator's ice level optics. Replacing a cracked or missing cover helps protect the board and keep the beam path clear for reliable ice making. What it does:

• Shields the emitter board and lens from moisture, frost, and debris
• Aligns the infrared beam path across the ice bin to the receiver
• Helps secure and position the ice level optics assembly
• Common symptoms: broken/missing cover, intermittent or no ice production due to optics misalignment or obstruction

• 1 emitter cover

• Disconnect power to the refrigerator before servicing
• Remove the ice bin to access the optics components
• Release the old cover's retaining tabs or fastener and lift it off; avoid touching board components
• Position and secure the new cover, then restore power and test ice maker operation

This dispenser motor assembly drives the refrigerator's in-door ice dispenser so cubes dispense when you press the paddle. Replacing a weak, seized, or noisy motor restores smooth, reliable operation of the dispenser mechanism. What it does:

• Powers the dispenser mechanism to move ice through the chute when activated
• Works with the switch and control to deliver ice on demand
• Failure can cause no ice dispensing, a humming/clicking noise, or intermittent operation
• Present as the auger/drive not turning even though the dispenser is selected

• One dispenser motor assembly

• Disconnect power to the refrigerator before servicing
• Access the dispenser area per your model; remove trim/covers carefully to avoid breaking tabs and watch for sharp edges
• Note wire lead orientation and mounting layout; transfer any reusable brackets or spacers from the old unit
• Restore power and test dispenser for proper operation after reassembly