Kenmore Washer 110.15954401 (11015954401, 110 15954401) Parts

The Agitator Washer is an OEM part for Whirlpool washing machines. It is designed to fit between the agitator and the agitator drive shaft, ensuring smooth and effective agitation of clothes during the wash cycle. 

Over time, the agitator washer can wear out or become damaged due to the constant movement and pressure exerted during wash cycles. Causes of a bad agitator washer can include normal wear and tear, exposure to heavy loads, or misuse that puts excessive stress on the part.

Symptoms of a bad agitator washer include:

• Agitator not moving or moving improperly
• Unusual noises during the agitation cycle
• Poor cleaning performance
• Agitator becoming loose or detached

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Suspension Spring Retainer is an OEM part for Whirlpool washing machines. It secures the suspension springs, which are crucial for stabilizing the washing machine tub during the wash and spin cycles.

You should replace the suspension spring retainer if it becomes damaged or worn out. Causes of a bad suspension spring retainer include the natural wear and tear from constant movement and load-bearing, impact damage, or corrosion from prolonged exposure to moisture.

Symptoms of a bad suspension spring retainer include:

• Excessive vibration or shaking during operation
• Loud banging noises during spin cycles
• The washing machine tub appearing off-balance
• Leaks from the tub due to instability

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Spin Tube Thrust Washer is an OEM component for Whirlpool washing machines. It is a washer that fits around the agitator shaft and helps create a seal between the agitator shaft and the aluminum tub. This washer allows the agitator to spin freely during the wash and spin cycles without causing excessive vibration or noise. 

Symptoms of a bad spin tube thrust washer include:

• Noises like banging or clunking coming from the agitator area
• Shaking or vibrating of the washer tub during spinning 

Causes of a bad thrust washer include normal wear and tear after extended use. Exposure to extended periods of unbalanced loads can also put excessive strain on the washer components and lead to premature failure of the thrust washer seal.

This replacement part is also compatible with select Kenmore, Maytag, KitchenAid, and Jenn-Air models.

The Spin Tube Bearing is an OEM replacement part for Whirlpool washing machines. It is a stationary bearing located inside the tub that supports the agitator and spin basket during operation. The bearing works to reduce friction and facilitate smooth spinning motion.

Symptoms of a bad spin tube bearing include:

• Excessive vibration or noise during the spin cycle
• The agitator or basket wobbling noticeably
• Difficulty Balancing loads
• Premature wear of other components

Causes of a bad bearing can include wear and tear due to repeated use over time, damage from cleaning products or foreign objects inside the tub, or improper handling during repairs.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Vacuum Break is an OEM part for Whirlpool washing machines, designed to prevent the siphoning of water back into the machine once it has been drained. This part ensures that dirty water does not re-enter the wash drum, maintaining the cleanliness of the wash cycle and protecting the integrity of the clothes being washed.

A malfunctioning Vacuum Break can lead to various issues, including inefficiencies in water use, prolonged or ineffective wash cycles, and even the risk of mildew or odors developing from standing water. 

Symptoms of a bad Vacuum Break include:

• Water siphoning back into the tub after the spin cycle
• Unusual noises coming from the washing machine during or after the drain cycle
• Clothes being wetter than usual at the end of the cycle, indicating incomplete draining
• Potential leaks or water buildup at the back of the washing machine

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Retainer Clip is an OEM replacement part for Whirlpool direct drive washing machines.

Causes of a bad retainer clip can include wear and fatigue from continuous vibration over many wash cycles. Cracks or breaks in the plastic material may develop as well.

Symptoms of a bad Retainer Clip include:

• Water leaks detected around the pump area inside machine cabinet
• Loosening of hoses or tubes interrupting proper drainage flow
• Potential pump component detachment from disconnected lines
• Damage to neighboring components submerged by leaked water

The OEM Whirlpool part is also compatible with Maytag, Jenn-Air, and select Kenmore models.

The Cover Seal is an OEM part for Whirlpool washing machines. This seal ensures a tight fit between the washer's cover and the tub, preventing water from leaking during the wash cycle. It helps maintain the efficiency and cleanliness of the washing process by keeping water contained within the tub.

Common causes of a bad seal include wear and tear over time, exposure to harsh detergents, or physical damage from regular use.

Symptoms of a bad cover seal include:

• Water leaking from the washer
• Excess moisture around the washer
• Visible cracks or deformities in the seal
• Reduced washing efficiency

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Gearcase Oil Seal is an OEM part for Whirlpool washing machines. This seal is located in the gearcase, preventing oil from leaking out while ensuring the internal components are properly lubricated. The kit contains two plastic seals that slide over the shaft to create a tight oil barrier.

Causes of a bad oil seal can include wear and tear over time, exposure to high friction and heat, or accidental damage during maintenance. A faulty oil seal can lead to oil leaks, which may cause further damage to the gearcase and other components.

Symptoms of a bad gearcase oil seal include:

• Oil leaks underneath the washer
• Loud noises during operation
• Washer not spinning or agitating properly
• Visible wear or damage to the seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Neutral Drain Kit is an OEM part for Whirlpool washing machines. This kit facilitates the neutral drain function, which allows the washer to drain water without spinning the tub, ensuring efficient water removal before the spin cycle begins.

Causes of a bad neutral drain kit can include wear and tear over time, mechanical failure of the components, or damage due to improper installation or handling. A faulty neutral drain kit can lead to draining issues, affecting the overall performance of the washing machine.

Symptoms of a bad neutral drain kit include:

• Washer not draining properly
• Extended or incomplete drain cycles
• Water remaining in the tub after the drain cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Outer Tub Ring Seal is an OEM part for Whirlpool washing machines. This seal is essential for maintaining a watertight connection between the outer tub and the tub ring, preventing water from leaking during the wash and spin cycles.

Causes of a bad tub ring seal can include regular wear and tear over time, exposure to harsh detergents or chemicals, or damage from foreign objects during the washing process.

Symptoms of a bad outer tub ring seal include:

• Water leaking from the washing machine during operation
• Visible cracks or tears in the seal
• Excessive moisture or water damage around the washing machine
• Mold or mildew buildup due to persistent leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Leveling Leg is an OEM part for Whirlpool washing machines. It provides support and adjustment capability to compensate for uneven surfaces or flooring. By adjusting the height of the rear leveling leg, you can achieve a balanced and stable position for your appliance.

Causes of a faulty or damaged rear leveling leg can include regular use, accidental impact, or wear and tear. A damaged leveling leg can lead to an unstable appliance, increased vibrations, or difficulty in maintaining a level position.

Symptoms of a bad rear leveling leg may include:

• Appliance wobbling or rocking during operation
• Uneven distribution of weight
• Difficulty in aligning the appliance with adjacent units or countertops

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Seal is an OEM part for Whirlpool washing machines. This part provides a tight seal around the washer shaft, preventing water from leaking out of the tub during the wash cycle.

Causes of a bad shaft seal can include wear and tear over time, exposure to harsh detergents or cleaning agents, or damage from foreign objects that may have gotten into the washer. 

Symptoms of a bad shaft seal include:

• Water leaking from the bottom of the washing machine
• Excessive noise during operation
• Visible damage or wear on the seal
• Wet spots or puddles under the washer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Clutch Retaining Clip is an OEM part for Whirlpool washing machines. This clip secures the clutch assembly, which is essential for the proper engagement and operation of the washer's transmission.

Causes of a bad retaining clip can include repeated mechanical stress, corrosion, or accidental damage during maintenance or repair.

Symptoms of a bad retaining clip include:

• Washer not spinning or agitating properly
• Unusual noises during operation
• Excessive vibrations or movement
• Washer failing to complete cycles correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head