Kenmore Washer 110.24722300 (11024722300, 110 24722300) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62646
This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.
- Secures the clutch spring within the clutch assembly to prevent movement or dislodging
- Maintains correct spring preload for consistent clutch engagement
- Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
- Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap
What's included: 1 clutch spring cap Install notes:
- Unplug the appliance and shut off water before servicing
- Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
- Carefully relieve spring tension and note the orientation of the spring and cap before removal
- Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly
Do-It-Yourself Stories from Customers like You
My washer wouldn't go into a spin cycle. Joshua P. • Cohutta , GA • April 18, 2021
I bought a clutch liner kit installed it in 5 minutes now it spins faster than ever.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 279868
This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:
- Provides a clean, finished edge and covers sharp cabinet/console edges
- Helps keep adjacent parts aligned and secured around the opening
- Restores appearance when original trim is cracked, warped, discolored, or missing
- Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts
What's included:
Install notes:
- Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
- Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
- Transfer any reusable clips/inserts from the old trim to the new part.
- Align and snap/screw the new trim into place; do not overtighten.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 285320
This siphon break kit prevents water from siphoning back out of the washing machine tub through the drain hose during the fill cycle. It acts as an air gap device installed on the drain line to ensure proper water levels are maintained. Replace this kit if your washer is not filling properly, takes too long to fill, or you notice water draining out as fast as it fills.
Do-It-Yourself Stories from Customers like You
I needed a siphon valve for an old maytag washer Shane F. • San Anselmo , CA • April 17, 2015
I bought a part and it worked perfectly. I was able to connect a flexible pipe to the siphon valve and set up a grey water system from our washing machine.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP384496
Connects drain hose sections to prevent leaks and restore proper wastewater drainage. Replace if coupling cracks or connection leaks during draining.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10083190
Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8538246
Clothes not getting clean? A worn agitator may not be rotating properly to wash clothes. This washer agitator assembly restores cleaning action.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9740848
The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.
Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.
Symptoms of a bad mounting screw include:
- Loose or rattling switch within the console face
- Difficulty selecting cycles as buttons wobble out of place
- Water intrusion hastening corrosion of electrical terminals
- Potential shock hazards if live connections are exposed
This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Neptune mah4000 had a no spin but did pump water out but not all of it Guillermo S. • Chicago , IL • March 06, 2017
I had the problem couple years ago I bypassed unbalance switch it worked fine for a couple years and had the same problem again so ruled out unbalanced switch. Door lock light on and checked made sure wax motor pushed out all the way too the second switch for spin check OK, so took a chance on displacement switch x2. My family loves to over load it and also replaced by passed unbalance switch and boom every thing went back to normal. Its also good to clean every thing when apart.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3357027
Drain hose nozzle that attaches to the end of your washer's drain hose. Replace if cracked, broken, or missing to ensure proper hose connection.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16272
Leaking water connection? This hose coupling creates a secure seal between your washer hose and water inlet, stopping drips and loose connections. DIY fix.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 285442
Connects the drain hose to the washer drain outlet. Replace this coupling kit if cracked, broken, or leaking to restore a secure connection.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10876590
Wire connector block for washers. Transfers electrical connections between wiring harnesses. Replace if connector housing is cracked or melted.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3357328
Replaces the vacuum break inlet hose connecting the water inlet to your washer tub. Needed when original hose is cracked, burst, leaking, or damaged.
Do-It-Yourself Stories from Customers like You
My washing machine smelt horrible Bryan W. • Ogdensburg , NY • August 20, 2018
First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available....
Read more
More
$19.31
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: WP387240
The Balance Ring is an OEM part for Whirlpool washing machines. This part maintains the stability of the washer drum during the spin cycle. It contains liquid that helps balance the load, minimizing vibrations and noise while ensuring smooth operation.
Causes of a bad balance ring can include general wear and tear, exposure to heavy or unbalanced loads, or physical damage.
Symptoms of a bad balance ring include:
- Excessive shaking or vibrating during the spin cycle
- Loud banging noises
- Washer moving or walking during operation
- Uneven or off-balance loads
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Washing machine would shake so bad during the spin cycle that it would move about a foot Charles L. • Arroyo Grande , CA • April 17, 2017
I first checked to make sure the washer was level. The washer is on a concrete floor. After watching lots of you tube videos I ordered all the parts that could be causing this problem. I ordered: Balance Ring, Suspension Pad Kit (3 rectangle plastic wear pads), Tub Suspension Pads(3 curved plastic wear pads), Suspension Spring, and a Spanner Wrench tool. After getting the washer apart it was obvious that the problem was the Tub Suspension Pads they had completely worn away so that only the...
Read more
More
$81.74
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 63849
Replace your washer's cracked or leaking outer tub. This housing holds the inner basket and prevents water from leaking into the machine's interior.
Do-It-Yourself Stories from Customers like You
Outer tub cracked Brian H. • North Tonawanda , NY • February 06, 2015
Replaced tub and center post seal
Read more
More
$234.53
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8546461
Fixes grinding noise or basket won't spin issues by disengaging the brake during spin cycles. Restores smooth operation when cam wears out or breaks.
Do-It-Yourself Stories from Customers like You
No spin every thing else worked made high speed ticking noise Anthony D. • Follansbee , WV • May 12, 2015
First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in...
Read more
More
$5.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 279954
White end cap kit with left and right caps for the dryer control panel ends. Provides finished appearance and protects panel edges.
More
$83.47
Out Of Stock
Usually ships within 4 - 14 days