Kenmore Dryer 110.70096991 (11070096991, 110 70096991) Parts

Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

Dryer won't heat or pilot lights but shuts off? This gas valve assembly controls burner ignition and flame. Typical DIY repair in 45-60 minutes.

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes miss

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens pa
  Do-It-Yourself Stories from Customers like You Missing baffles   Anna S. • Shoreview , MN • January 31, 2016

  I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles. Read more

Stationary shelf that sits inside the dryer drum for drying shoes, sweaters, and delicates without tumbling. Replace if rack is missing, cracked, or damaged.

Dryer belt slipping off motor pulley or making squealing noises? The belt restrainer keeps the drive belt aligned. Moderate DIY repair with video guide.

Specs: 10-16 x 1/2 inch.

Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.

Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essen

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may com

Left-side door hinge for dryers. Replaces broken, bent, or deformed hinges that prevent the door from closing properly. Simple installation.

This screw-and-washer fastener is a factory-size 8-18 x 5/16 hardware piece used to secure appliance panels and components. Replace stripped, rusty, or missing hardware to restore a tight, rattle-free fit and proper alignment. What it does:

• Fast
  Do-It-Yourself Stories from Customers like You Burners were leaking gas igniters didn't work   Christine B. • Meredith , NH • February 13, 2016

  I removed the burners, which were rusted and needed some tapping.They were pretty stubborn to remove from the insert. I removed the spark igniters, which were rusted where they screwed into the burner and then removed the venturi tubes.. Once this was done, I installed the new igniters to the underside of the new burner. I then installed the burners, which only took simple placement and a quarter turn to lock them in. I then hooked up the igniter wire to the new spark igniters. The repair... Read more

Push-in.

This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.

• Retains the hinge/hi
  Do-It-Yourself Stories from Customers like You Dryer no start   George Larry B. • Niceville , FL • November 19, 2019

  Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now. Read more