Kenmore Dryer 110.7058700 (1107058700, 110 7058700) Parts

The Terminal Block Kit is an OEM part for Whirlpool dryers. This kit includes the terminal block, wires, wire connectors, screws, brackets and instructions.

Common causes of a bad terminal block include overheating due to loose connections, corrosion from moisture exposure, and physical damage from handling or installation errors.

Symptoms of a bad terminal block kit include:

• Dryer not starting or losing power during operation
• Burning smell or visible burn marks near the terminal block
• Loose or frayed wires connected to the terminal block
• Intermittent electrical issues or malfunctioning controls

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Includes screws and wire connectors. For the complete terminal block kit use 279320.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This U-type nut clips over a sheet-metal edge to create a durable threaded anchor for a screw. It helps secure panels, trim, and brackets so fasteners hold tight and components stay aligned and rattle-free. What it does:

• Clips onto thin sheet metal to provide captive threads where a standard nut cannot be used
• Holds screws securely to fasten panels, trim pieces, or mounting brackets
• Addresses issues like loose panels, missing/broken clips, or screws that will not tighten
• Helps reduce vibration and rattling from unsecured components

• 1 U-type nut

• Disconnect power and shut off gas/water before servicing
• Position the U-nut over the panel edge with the threaded side aligned to the hole
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged or corroded hardware to ensure a secure hold

This bearing ring is a small, low-friction spacer used in the dryer's drive system to let rotating components spin smoothly and quietly. Replacing a worn ring helps reduce drag, eliminate squeal, and protect related parts. What it does:

• Provides a bearing surface between a rotating wheel/pulley and its bracket
• Helps maintain smooth belt tracking and consistent tumble
• Reduces friction and wear on the belt and pulley/roller
• Common symptoms of wear: squealing/chirping while running, intermittent drum start, drag or burning-rubber smell

• 1 bearing ring

• Disconnect power; for gas dryers, also shut off gas supply
• Access the drive system; release belt tension and remove the affected pulley/roller as required
• Note the order/orientation of spacers, washers, and clips; install the new ring in the same position
• Hand-rotate the assembly to ensure free movement before reassembly and testing

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

Specs: 10-16 x 1/2 inch.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.

• Retains the hinge/hinge pin to prevent shifting or separation
• Helps maintain door alignment to avoid rubbing, sagging, or binding
• Replaces a clip that is bent, cracked, corroded, or missing
• Common signs it's needed: loose or wobbly door, difficulty closing, misaligned door, visible damaged/missing clip

• Unplug the appliance and, if applicable, remove items from the door to reduce weight
• Support the door before working on the hinge
• Remove any hinge cover/fasteners, swap the clip, and ensure it seats fully
• Reassemble and check door alignment and smooth operation

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit

This vinyl door seal lines the perimeter of the appliance door to help block air and moisture leaks, cushion the close, and maintain proper operation. Replace a worn seal to restore a tight, quiet, reliable door closure.

• Creates a continuous seal around the door opening to reduce leaks
• Helps contain air and moisture and dampens door vibration
• Replace if the seal is torn, cracked, flattened, or coming loose
• Symptoms include gaps or drafts at the door, noise, or visible wear

• Disconnect power; for gas appliances, also shut off the gas supply
• Remove inner door panel/trim as needed to access the seal area
• Remove the old seal and clean the mounting surface of residue
• Install the new seal without stretching; if your model uses adhesive, apply per instructions and allow proper cure time

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Replacement drum baffle that lifts and tumbles clothes inside the dryer for more even drying and helps prevent garments from snagging. Restores proper drum agitation to reduce noise and improve drying performance. What it does:

• Lifts and separates clothes as the drum turns to promote even heat exposure and drying.
• Helps keep items from bunching or wrapping around the drum, which can cause uneven drying.
• Reduces rattling, thumping, or scraping noises tied to a loose or damaged lifter.
• Protects fabrics from snagging or rubbing against the drum surface.

• Disconnect power to the appliance before beginning service to avoid shock or injury.
• Access may require removing the dryer front panel or drum.
• Keep fasteners and mounting tabs aligned during reassembly to ensure the baffle seats correctly.

This 5/16-18 x 3/4 machine bolt replaces a missing or damaged fastener used to secure panels, brackets and components in many home appliances. It restores proper fit and helps stop rattling or loose parts. What it does:

• Secures panels, brackets or assemblies to maintain proper alignment and safe operation
• Restores clamping force where a stripped or missing bolt lets parts shift or vibrate
• Helps eliminate rattling, scraping or movement caused by loose fasteners
• Matches standard 5/16-18 coarse threads for direct replacement of the OEM bolt

• Disconnect power to the appliance before servicing to reduce shock and injury risk
• Start threads by hand to avoid cross-threading; tighten using the correct socket or wrench
• Do not overtighten; snug to manufacturer torque or until secure to avoid stripping threads
• If the original mating threads are damaged, inspect the receiving part and repair or replace as needed

This replacement motor pulley helps the dryer drive system turn the drum by guiding the drive belt for smooth rotation and reliable operation. Fits compatible Whirlpool-built dryers and restores proper drum movement when worn. What it does:

• Guides and supports the drive belt so the drum can rotate smoothly during operation
• Restores proper belt alignment to reduce slipping and uneven tumbling
• Helps eliminate squealing or scraping noises caused by a worn or damaged pulley
• Prevents accelerated belt wear that can lead to the drum not turning

• Disconnect power to the appliance before starting any repair
• Inspect the drive belt and other related components; replace if worn or damaged
• Use common hand tools; supports and pulleys may require holding the motor or drum during removal