Kenmore Dryer 110.70882991 (11070882991, 110 70882991) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP18776
This small spring clip secures the top panel of the dryer to the cabinet frame. It snaps into place to hold the top firmly shut during operation. Replace this clip if your dryer's top panel feels loose, pops open during use, or won't stay latched when closed.
Do-It-Yourself Stories from Customers like You
Clothes dryer drum stopped rotating Edward J. • Eclectic , AL • February 20, 2015
Located model number and went to Appliance Parts Pros.com to check the repair instructions on belt and motor. Used the suggestions to diagnose problem as a broken belt. I also ordered two top locks to replace the originals that were very brittle plastic that broke when I opened the dryer.
Ordered the parts on Presidents Day, and received the parts the next day. The dryer was back in service in 24 hours.
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694424
If your dryer won't stay lit or shuts off after a few minutes, the gas limiter may be faulty. This regulator controls safe gas flow to the burner.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$27.37
- Compare At:
-
$32.30
- You Save:
-
$4.93
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3405184
The Door Handle is an OEM component for Whirlpool dryers. It provides convenient access to load and unload clothes through the dryer door opening.
Causes of a bad door handle can include normal wear and tear over extended use. Repeated clutching and releasing of the handle leads to fatigue of rubberized grip areas and loosening of mechanical connections. Accidental falls or impacts when transporting dry loads of clothes could also damage the handle structure or mounting.
Symptoms of a bad dryer door handle include:
- Increased play, wobble, or looseness when grasped
- Detachment or separation from the door assembly
- Cracks, splitting, or broken areas compromising the grip surface
- Inability to smoothly open or close the dryer door
Compatible models also include Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore dryers.
Do-It-Yourself Stories from Customers like You
Missing oven and broiler handle Travis W. • Zwolle , LA • October 15, 2014
Separated oven door by removing screws. Inserted handle and secured with clips, and reassembledo door with screws provided.
In served broiler handle and snappedal into place.
Read more
More
$56.34
- Compare At:
-
$66.48
- You Save:
-
$10.14
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.56
- Compare At:
-
$8.90
- You Save:
-
$1.34
Genuine Whirlpool part
By: Whirlpool
Part Number: 279366
The Moisture Sensor is an OEM part for Whirlpool dryers. This part detects the moisture level in the clothing during the drying cycle, allowing the dryer to adjust the drying time accordingly.
Causes of a bad moisture sensor can include regular wear and tear, buildup of lint or residue, or physical damage.
Symptoms of a bad moisture sensor include:
- Clothes taking longer to dry or coming out still damp
- The dryer not stopping when clothes are dry
- The dryer shutting off prematurely
- Inconsistent drying results
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dampness sensor was broken George L. • Marquette , MI • March 24, 2014
Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned.
Read more
More
$74.95
- Compare At:
-
$89.19
- You Save:
-
$14.24
Genuine Whirlpool part
By: Whirlpool
Part Number: WP234826
Converting dryer from propane to natural gas? This orifice regulates gas flow in the burner assembly. Easy DIY fix, typically done in under 1 hour.
Do-It-Yourself Stories from Customers like You
Propane to natural gas conversion on range and dryer Vincent P. • Howell , NJ • October 09, 2014
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time.
Read more
More
$34.33
- Compare At:
-
$40.51
- You Save:
-
$6.18
Genuine Whirlpool part
By: Whirlpool
Part Number: WP98234
U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.
Do-It-Yourself Stories from Customers like You
Broken hinge Ronald B. • Manchester , CT • October 21, 2019
Followed the video on how to replace the hinge I also replaced the dryer top locks while I had it open
Read more
More
$11.78
- Compare At:
-
$14.02
- You Save:
-
$2.24
Genuine Whirlpool part
By: Whirlpool
Part Number: WP348197
This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:
- Maintains proper spacing and support between adjoining parts
- Helps prevent metal-to-metal contact, reducing scraping or grinding noises
- Addresses wobble or excess play when the original washer is worn, deformed, or missing
- Restores smoother movement and alignment in the assembly
What's included:
Install notes:
- Disconnect power and water supply before servicing; for gas combos, also shut off gas
- Refer to your model's parts diagram for location and orientation
- Track the order of any shims/spacers during disassembly and reinstall in the same sequence
- Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts
Do-It-Yourself Stories from Customers like You
Screaching noise Linda Z. • Kailua Kona , HI • February 06, 2015
Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP388326
This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:
- Fastens the control console/control panel to the cabinet or top panel
- Helps maintain alignment and reduces vibration and rattling
- Replaces a missing, stripped, or rusty original screw
- Common fix for a loose or lifting console/panel
What's included:
Install notes:
- Disconnect power before service; if applicable, shut off gas/water
- Support the console to avoid straining wiring harnesses
- Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
- Use the correct driver style for your model's hardware
Do-It-Yourself Stories from Customers like You
Leaking water from the tub seal David C. • Bessemer City , NC • January 27, 2018
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE
At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain.
Several months before I had this issue with the water leaking...
Read more
More
$7.56
- Compare At:
-
$8.32
- You Save:
-
$0.76
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694422
Spring installs inside the gas pressure regulator assembly on gas dryers. Replace if lost during conversion between natural gas and propane fuel types.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$17.48
- Compare At:
-
$20.80
- You Save:
-
$3.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694423
Dryer making high-pitched sound when igniter turns on? This natural gas regulator maintains proper gas pressure to burners. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
$87.40
- Compare At:
-
$104.01
- You Save:
-
$16.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3394509
Low-friction bearing ring for smooth drum rotation. Replace when you hear squealing or scraping during cycles. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Not heating. Lamar B. • Rising Fawn , GA • November 01, 2021
Looked up the part on AppliancesPartsPros.com. Ordered the part. Installed now it works like new.
Read more
More
$57.39
- Compare At:
-
$68.29
- You Save:
-
$10.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693995
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
Do-It-Yourself Stories from Customers like You
There was no power cord and accessories to attach it Terry C. • Martin , TN • December 27, 2016
I put all pieces that I ordered on the dryer and plugged it in.
Read more
More
$7.56
- Compare At:
-
$8.90
- You Save:
-
$1.34
Genuine Whirlpool part
By: Whirlpool
Part Number: W10823508
This assembly includes the gas burner and valve components that control the flow and ignition of gas in your dryer. It is responsible for producing the heat needed to dry clothes. Replace this assembly if your dryer is not heating, heats intermittently, or if you notice the gas igniter glowing but the burner failing to light.
Do-It-Yourself Stories from Customers like You
Slow gas leak Roger T. • Houston , TX • October 11, 2016
Valve (or a component on it) was slowly leaking gas. I was able to easily replace the entire gas assembly with this order. Item was mostly pre-assembled, and contained all parts needed, including new igniter and coils.
Read more
More
$181.54
- Compare At:
-
$270.07
- You Save:
-
$88.53
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13