Kenmore Dryer 110.77751600 (11077751600, 110 77751600) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694423
Dryer making high-pitched sound when igniter turns on? This natural gas regulator maintains proper gas pressure to burners. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: 280119
This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.
Do-It-Yourself Stories from Customers like You
Weak or no burner flame Michael T. • North Reading , MA • November 16, 2018
Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(...
Read more
More
$235.95
- Compare At:
-
$280.78
- You Save:
-
$44.83
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10080190
This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.
- Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
- Helps keep brackets, panels, and other parts firmly in place
- Replaces damaged or missing hardware that can cause looseness or rattling
- Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely
What's included: 1 nut Installation notes:
- Disconnect power and, if applicable, shut off water and gas before servicing
- Match thread size to the original part; start threading by hand to avoid cross-threading
- Reinstall any washers/spacers in the original order; tighten securely without over-tightening
- If the original used a locking feature or threadlocker, reinstall per your product's service information
Do-It-Yourself Stories from Customers like You
Needed to replace a left thread nut Russell C. • Elizabeth , IN • September 24, 2021
I ordered the nut and was shocked when it arrived the next day.
Read more
More
$7.48
- Compare At:
-
$8.83
- You Save:
-
$1.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
$87.40
- Compare At:
-
$104.01
- You Save:
-
$16.61
Genuine Whirlpool part
By: Whirlpool
Part Number: 279782
Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.
Do-It-Yourself Stories from Customers like You
Broken belt switch Jack F. • Hermosa Beach , CA • July 08, 2016
Every time I tried to start our dryer, the "Sensing Light" came on, I heard a little "click," and the dryer would not start.
According to the very helpful Appliance Parts Pros. videos, I was able to dismantle, diagnose a few components, and discover the broken part. In this case, it was a Broken Belt Switch.
I ordered the part, we went on vacation for a week, and when we returned home the part was at our residence. The next day, I installed the part and all is good now.
I am nearly 70 years...
Read more
More
$54.25
- Compare At:
-
$64.56
- You Save:
-
$10.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693995
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
Do-It-Yourself Stories from Customers like You
There was no power cord and accessories to attach it Terry C. • Martin , TN • December 27, 2016
I put all pieces that I ordered on the dryer and plugged it in.
Read more
More
$7.48
- Compare At:
-
$8.90
- You Save:
-
$1.42
Genuine Whirlpool part
By: Whirlpool
Part Number: 279923
Dryer won't heat or pilot lights but shuts off? This gas valve assembly controls burner ignition and flame. Typical DIY repair in 45-60 minutes.
Do-It-Yourself Stories from Customers like You
The gas Dryer would not dry clothes because the pilot would ignite but the gas would turn on for a moment then turn off. Eventually the gas would not come on at all. Kenneth S. • Columbus , MI • March 24, 2014
I decided the problem was with the gas valve and I found the part on your web site. I ordered it and received the part in 3 days. I replaced the valve and the dryer works like new! This also gave me an opportunity to vacuum out the dust/lint that collects in and around the dryer.
Read more
More
$158.95
- Compare At:
-
$190.74
- You Save:
-
$31.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10109200
This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.
- Fastens panels, brackets, or internal parts to the cabinet/frame
- Helps maintain alignment to reduce vibration and rattling
- Replaces lost, stripped, or corroded screws
- Common symptoms: loose panels/trim, rattles, or a screw that won't tighten
What's included: One screw. Install notes:
- Disconnect power; shut off water or gas if applicable
- Match thread and length to the original; replace one at a time to keep alignment
- Start threads by hand to avoid cross-threading; use the correct driver
- Tighten snugly—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Missing baffles Anna S. • Shoreview , MN • January 31, 2016
I ordered two replacement baffles and screws, then lifted the top of the dryer to access the drum and installed the two new baffles.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 8212450A
Stationary shelf that sits inside the dryer drum for drying shoes, sweaters, and delicates without tumbling. Replace if rack is missing, cracked, or damaged.
Do-It-Yourself Stories from Customers like You
Loud squeaking noise Karen H. • Crossville , TN • March 30, 2015
I went online and typed in my model number. I was just going to order the dryer belt, but decided that changing all the movable parts at the same time would be best - I definitely recommend doing this, since it was the tensioner pulley and not the belt. My husband is handy, which is why this was not a problem. The whole dryer needs to come apart in order to do this repair. At first I thought I received the wrong parts because I have a front load washer and dryer set, but the picture on the...
Read more
More
$71.95
- Compare At:
-
$86.34
- You Save:
-
$14.39
Genuine Whirlpool part
By: Whirlpool
Part Number: W10470674
Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.
Do-It-Yourself Stories from Customers like You
Needed to switch dryer to side exhaust Allen B. • Clarksville , IA • January 23, 2015
Went on line looking on how to accomplish this and Appliance parts pro site came up and it was exactly what I needed. Order was sent on Sunday note and on Tuesday afternoon it was delivered.
Just got done installing. Took longer to gather up the needed tools then to install. The instructions were awesome . complete wife great photos
Read more
More
$71.95
- Compare At:
-
$86.34
- You Save:
-
$14.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387560
Right-hand door hinge for dryers. Replaces broken, bent, or sprung hinges that prevent the door from closing properly. Easy DIY installation.
Do-It-Yourself Stories from Customers like You
Deformed hinges Todd B. • Kalamazoo , MN • September 29, 2014
I removed the old hinges and replaced them with the new hinges. It was probably the easiest repair I've ever had to do.
Read more
More
$61.69
- Compare At:
-
$73.41
- You Save:
-
$11.72
Genuine Whirlpool part
By: Whirlpool
Part Number: WP660658
This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.
Do-It-Yourself Stories from Customers like You
Motor was bad and also needed general maintenance. Daniel E. • Litchfield , IL • April 14, 2020
Took it apart. Replaced various general maintenance parts, rollers, seals, clean out all the lint and replaced motor and put a new blower on it.
Read more
More
$10.37
- Compare At:
-
$12.44
- You Save:
-
$2.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387559
Left-side door hinge for dryers. Replaces broken, bent, or deformed hinges that prevent the door from closing properly. Simple installation.
Do-It-Yourself Stories from Customers like You
Deformed hinges Todd B. • Kalamazoo , MN • September 29, 2014
I removed the old hinges and replaced them with the new hinges. It was probably the easiest repair I've ever had to do.
Read more
More
$61.69
- Compare At:
-
$73.41
- You Save:
-
$11.72
Genuine Whirlpool part
By: Whirlpool
Part Number: W11226088
Covers and protects your dryer's light bulb from heat and debris while diffusing illumination. Replace if cracked, yellowed, or missing. Confirm fit.
Do-It-Yourself Stories from Customers like You
The pulley wheel the light cover James B. • Philadelphia , PA • August 06, 2017
Been doing these repairs for a lil while now. Your Company provides Videos on Appliance Brands that detail how to get to the part that is suspected and how to Test and Repair. I suspected a Part by it's sound and followed the Video to get to the part and made the repair.
Read more
More
$26.95
- Compare At:
-
$31.80
- You Save:
-
$4.85
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399640
Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.
Do-It-Yourself Stories from Customers like You
My kenmore dryer was not gnitind so therefore no heat also my washer was leaking under the machine Bill K. • Midland Park , NJ • November 24, 2014
THE WSHER WAS EASY BECAUSE THE DRAIN PUMP HAD TWO PENNIES INSIDE IT AND THEY CRACKED THE HOUSING.EASY FIX REPLACING THE DRAIN PUMP. WORKS LIKE A CHARM. DRYER WAS A BIT MORE WORK.I CHANGED THE IGNITER FIRST WITH YOUR ADVICE. STILL NOTHING. I THEN CHANGED THE COIL VALVE KIT. NO LUCK. NEXT WAS THE TEMP SWITCH ON THE PANEL. STILL NO GOOD.FINALLY THE THERMAL FUSE WAS RECOMMENDED. I WAS ABLE TO PURCHASE ONE LOCALLY AND IT WORKED . GREAT RELIEF.THANKS FOR ALL THE HELP AND RECOMMENDATIONS. YOUR...
Read more
More
$62.61
- Compare At:
-
$75.13
- You Save:
-
$12.52