Kenmore Dryer 110.97531702 (11097531702, 110 97531702) Parts

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

Side and bottom exhaust kit.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

The Door Strike is an OEM replacement part for Whirlpool dryers. This component ensures the dryer door securely latches, enabling the appliance to operate and preventing it from running with the door ajar. It works in conjunction with the door catch to maintain a proper seal during drying cycles.

Symptoms of a bad Door Strike include:

• The dryer door not latching or staying closed
• The dryer not starting due to the door remaining open
• The door popping open during operation
• Visible wear, bending, or damage to the strike

Causes of a failing Door Strike can include regular wear and tear, misalignment from improper use, or damage from slamming the door. Replacing a faulty strike ensures the dryer operates safely and efficiently.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

The Lint Screen Door is an OEM part for Whirlpool dryers. It is located at the front of the dryer and provides easy access to the lint screen. It helps to trap lint and debris from the drying process, preventing it from entering the dryer vent and potentially causing clogs or fire hazards.

Causes of a faulty or damaged lint screen door can include regular wear and tear, physical damage, or improper handling. These factors can result in issues such as difficulty in opening or closing the door, a loose or insecure fit, or reduced effectiveness in capturing lint.

Symptoms of a bad lint screen door may include:

• Difficulty in opening or closing the door
• Loose or wobbly door fit
• Lint bypassing the lint screen and accumulating in the dryer vent

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This spring clip secures small panels, brackets, or trim inside your appliance to maintain a snug fit and prevent movement. Replacing a fatigued clip helps restore proper alignment and reduce unwanted vibration or rattling. What it does:

• Provides spring tension to hold a component firmly in place
• Helps prevent vibration, rattling, or shifting during operation
• Replaces a bent, worn, corroded, or missing clip
• Common symptoms: loose or misaligned panel/trim, recurring rattles, or parts that won't stay secured

• 1 spring clip

• Disconnect power (and gas, if applicable) before servicing
• Access the clip location per your model's service/parts diagram
• Note the clip's orientation and attachment points before removal
• Use needle-nose pliers carefully to avoid bending adjacent tabs or brackets

This replacement washer is a small hardware component used in appliance assemblies to provide a stable bearing surface and proper spacing. Replacing a worn or missing washer helps maintain alignment, reduce vibration, and protect mating parts from damage.

• Distributes load under a nut, bolt, pin, or shaft to protect mating surfaces
• Maintains correct spacing and alignment within stacked components
• Helps reduce friction, vibration, and noise in moving assemblies
• Worn or missing washers can contribute to looseness, wobble, rattling, or premature wear

• Disconnect power and shut off gas/water before servicing
• Note the original order and orientation of parts during disassembly
• Inspect fasteners, shafts, and bushings; replace any that show wear or damage
• Tighten fasteners securely per the service manual; do not overtighten

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

This lint duct assembly forms the sealed air path between the lint screen and the blower. Replacing a damaged or leaking duct restores proper airflow and drying performance while helping keep lint contained within the filtration path.

• Directs air from the drum through the lint screen to the blower and exhaust
• Maintains a sealed passage to optimize airflow and drying efficiency
• Replace if cracked, warped, or loose, or if mounting tabs are broken
• Common symptoms: long dry times, weak exhaust airflow, lint inside the drum/cabinet, or visible damage/gaps

• Disconnect power and shut off gas supply before servicing
• Remove the lint screen and access panels as required by the model to reach the duct
• Note fastener locations; transfer any attached sensors, brackets, seals, and screws from the old duct to the new one
• Vacuum lint from the blower housing and vent path before reassembly; ensure the duct seats and seals evenly

Replacement housing that supports and protects internal components in compatible Whirlpool appliances. Restores structural integrity to the cabinet, helping reduce vibration and keeping wiring and components enclosed for safe, reliable operation. What it does:

• Provides the outer cabinet support that secures motors, controls and wiring
• Protects internal parts from debris and accidental contact
• Helps reduce rattling, vibration and misalignment symptoms caused by cracked or damaged cabinets
• Restores proper fit for panels and fasteners to eliminate rubbing or interference noises

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools are typically required; keep screws and clips organized during disassembly
• Some housings may require two people to position during replacement—avoid forcing parts to prevent damage
• Fasteners and any sealing gaskets are in good condition and replaced if worn

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual

Restore smooth operation of your dryer's lint screen cover with this lint screen door spring. It provides the correct tension so the cover opens and closes properly and the lint screen seats securely for reliable lint collection.

• Applies spring tension to the lint screen door/cover hinge
• Helps the lint screen and cover stay properly positioned
• A worn or broken spring may cause the cover to feel loose, pop open, or not stay closed
• May make inserting or removing the lint screen difficult

• Disconnect power; for gas dryers, also shut off gas supply
• Access the lint screen door area per your model's service information
• Note the original spring orientation; transfer the new spring carefully using needle-nose pliers
• Check cover operation and lint screen seating before restoring power