Kenmore Refrigerator 363.9534883 (3639534883, 363 9534883) Parts
Genuine Ge part
By: Ge
Part Number: WR60X187
The Condenser Fan Motor is an OEM part for GE refrigerators. It is designed to circulate air through the condenser coils, helping to dissipate heat and keep the refrigerator's internal components cool. This ensures efficient operation and prevents the compressor from overheating, which is essential for maintaining the refrigerator's performance and longevity.
You should replace the condenser fan motor if it becomes faulty. Causes of a bad fan motor can include electrical failures, wear and tear from regular use, or blockages that cause the motor to overheat or burn out. A malfunctioning fan motor can lead to inadequate cooling, increased energy consumption, and potential damage to other refrigerator components.
Symptoms of a bad condenser fan motor include:
- The refrigerator not cooling properly
- Unusual noises coming from the back of the refrigerator
- The compressor running hot or cycling on and off frequently
- The condenser coils feeling excessively hot
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Freezer section too warm
-
Noisy
-
Fridge too warm
See more...
Do-It-Yourself Stories from Customers like You
Side by side fridge had stopped cooling in both fridge and freezer and was hot to touch in center between the two Robert P. • King , NC • August 11, 2015
I googled the issue and read several articles. Most started with cleaning the coils (which mine are on the bottom) (19yr old Kenmore 363.9557812). I had not really ever cleaned them well, vacuuming did little. I had to remove the cardboard cover off the back of the frig, and blew them clean (front to back). Once that was done, I started cleaning from the back and noticed the fan wasn't turning week (condensor fan). Blew it out too, have it a good soon with a pencil, it puffed out a bunch of...
Read more
More
$226.48
- Compare At:
-
$269.51
- You Save:
-
$43.03
Genuine Ge part
By: Ge
Part Number: WR60X114
The Evaporator Fan Blade is an OEM component for GE freezers and bottom-mount refrigerator designs. Located inside the freezer compartment, this fan blade spins to circulate cold air evenly throughout the storage space.
Causes of a faulty evaporator fan blade include natural fatigue from running year-round. Freezers exposed to humid environments may experience faster corrosion.
Symptoms include:
- Abnormal sounds like knocking or clunking from inside the walls
- cold spots developing in certain freezer areas
- Higher power bills from inefficient temperature regulation
- Frost or ice patches forming on evaporator coils
This part is also compatible with some brands like Hotpoint, RCA, and Kenmore.
Do-It-Yourself Stories from Customers like You
Broken fan blade Thomas H. • West Blocton , AL • April 21, 2014
I used a set of ring pliers to remove the old retaining ring, then spread the plastic ribs around the fan motor shaft with a small flat bladed screwdriver to ease removal of the old fan blade. I reversed the process to replace the blade, gently tapping a socket from my socket wrench set placed over the motor shaft and ribs with a small rubber mallet. I stopped when the shaft protruded about 1/8" beyond the plastic ribs of the new fan blade, then installed the new retaining clamp ring with the...
Read more
More
$17.95
- Compare At:
-
$24.40
- You Save:
-
$6.45
Genuine Ge part
By: Ge
Part Number: WR17X11349
The Ice Maker Water Line is an OEM replacement part for GE refrigerators. It is an important supply line that delivers water from the main water source to the icemaker component. The water line allows water to flow smoothly, facilitating the icemaking process.
Causes of a bad water line can include cracks or punctures from impact or bending, mineral deposits and corrosion building up inside the line restricting flow, or improper connection fittings causing leakage.
Symptoms of a bad ice maker water line include:
- Irregular or insufficient ice production
- No water delivery to the icemaker despite activation
- Noticeable leaks or drips near the water line attachment points
- Strange knocking or hammering sounds are heard when the icemaker is running
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Water valve was leaking and return water line was leaking Ivan D. • Hialeah , FL • May 22, 2015
Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61
Genuine Ge part
By: Ge
Part Number: WR2X8474
The Ice Maker Fill Tube Grommet is an OEM part for GE refrigerators. This grommet creates a seal between the ice maker fill tube and the refrigerator, preventing leaks and ensuring that water is properly directed into the ice maker during the filling process.
Causes of a bad grommet can include regular wear and tear, damage from exposure to freezing and thawing cycles, or degradation from exposure to water and moisture.
Symptoms of a bad ice maker fill tube grommet include:
- Water leaks around the ice maker fill tube area
- Ice maker not producing ice properly
- Visible cracks or deformation in the grommet
- Water pooling inside or around the refrigerator
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Leaking
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$32.95
- Compare At:
-
$38.88
- You Save:
-
$5.93
Genuine Ge part
By: Ge
Part Number: WR51X443
This defrost heater and thermostat assembly melts frost from the evaporator and shuts off at the proper temperature during the defrost cycle, restoring airflow and helping the refrigerator maintain steady, reliable cooling performance.
- Heats the evaporator to clear frost/ice during the automatic defrost cycle
- Thermostat opens to terminate heat once a safe temperature is reached
- Helps restore air circulation to the fresh food section
- Common failure signs: heavy frost on the freezer back wall/evaporator, poor cooling or warm fridge, fan noise from ice contact, little or no water in the drain pan after "defrosts"
What's included: 1 pre-assembled defrost heater with defrost thermostat Install notes:
- Disconnect power before service; work on a fully de-energized appliance
- Access is typically behind the freezer's rear panel; remove shelves/ice components as needed
- Fully defrost before installing the new assembly to prevent damage and ensure proper fit
- Reinstall in the original locations; clamp the thermostat to the evaporator tubing and route wiring exactly as factory, away from sharp edges and moving parts
Do-It-Yourself Stories from Customers like You
Defrost heater not working Jayesh P. • La Canada , CA • June 12, 2014
I replaced defrost heater with thermostat. It is a very easy and there is YouTube tutorial video for that.
Read more
More
$117.95
- Compare At:
-
$145.61
- You Save:
-
$27.66
Genuine Ge part
By: Ge
Part Number: WR62X26536
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
- Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
- Helps maintain a proper seal to limit frost and moisture around the dispenser
- Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
- Wear or sticking of the armature/spring can hinder movement and affect dispenser operation
What's included: 1 armature kit Installation notes:
- Unplug the refrigerator and shut off water to the dispenser before servicing
- Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
- Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
- Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation
Do-It-Yourself Stories from Customers like You
Water was overflowing out of the ice maker during fill process and freezing into a block of ice! Steven B. • Arlington , TX • March 17, 2015
Replaced the water supply valve...boom!
Read more
More
$52.73
- Compare At:
-
$63.28
- You Save:
-
$10.55
Genuine Ge part
By: Ge
Part Number: WR60X10262
This replacement motor powers the dispenser's auger/crusher mechanism to move ice from the bucket to the chute. Replacing a weak or seized motor helps restore reliable cube or crushed-ice dispensing from the freezer door.
- Drives the ice auger/crusher to feed ice from the bucket through the dispenser chute
- Helps deliver cubes or crushed ice, depending on the control selection
- Common symptoms: no ice dispensing, auger not turning, loud humming or grinding, intermittent or weak dispensing
- Located in the freezer-door dispenser assembly and engages the ice bucket coupler
What's included: One dispenser crusher motor. Install notes:
- Disconnect power to the refrigerator before servicing
- Remove the ice bucket and dispenser trim/panel to access the motor; note wire orientation and fasteners
- Transfer any mounting hardware or coupler from the old motor
- Reassemble, restore power, and test ice dispensing
Do-It-Yourself Stories from Customers like You
Needed new ice maker motor and circuit board Edward Z. • Berlin , CT • August 19, 2016
I watched the help videos first, then ordered the parts, and installed all items as in the video.
Read more
More
$146.95
- Compare At:
-
$174.58
- You Save:
-
$27.63
Genuine Ge part
By: Ge
Part Number: WR2X8818
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
- Holds the recess/ice door on its pivot within the dispenser assembly
- Helps the flapper close fully to seal the ice chute
- Restores smooth open/close action of the dispenser door
- Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute
What's included: 1 recess door retainer Install notes:
- Unplug the refrigerator before servicing the dispenser
- Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
- Note spring orientation and retainer position; transfer components to the new retainer
- Verify flapper movement and seal before reassembly and restoring power
Do-It-Yourself Stories from Customers like You
Yes ice was not coming out of the dispenser Jason S. • Goose Creek , SC • December 02, 2014
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well.
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR62X107
Door solenoid with plunger.
Do-It-Yourself Stories from Customers like You
When dispensing ice from the ice maker, the solenoid was buzzing loudly. It was also rusting badly. Brian B. • Hudson , NH • March 28, 2014
I ordered a new solenoid and when it arrived, I installed it as follows: I cut the power to the refrigerator. I then pulled off the rubber boot (and it's plastic frame) that covers the water switch. Then I removed the bezel that covers the front of the ice maker controls by pulling it straight out. Then I removed the four screws found on the assembly under the bezel. After pulling the assembly forward a bit, I detached the multi-wire connector attached to it and put the assembly aside....
Read more
More
$74.34
- Compare At:
-
$88.46
- You Save:
-
$14.12
Genuine Ge part
By: Ge
Part Number: WR17X3089
This dispenser crank links the dispenser solenoid and the ice chute door. When you press the dispenser lever, the crank pivots to open and close the ice door so cubes or crushed ice can dispense cleanly without warm air leaking into the freezer.
- Connects the solenoid to the ice chute door to control door movement
- Helps seal the chute when not dispensing to reduce frost and moisture issues
- Common failure signs include ice door not opening/closing, constant frost around chute, or warm/moist air leakage at dispenser
- Can cause ice clumping, frost buildup, or water/ice dispensed irregularly when worn or broken
What's included: 1 dispenser crank Install notes:
- Disconnect power before servicing the dispenser area
- Access typically requires removing the dispenser front panel and trim; use care with plastic tabs and wiring
- Note linkage orientation to the solenoid and door flap before removal
- Inspect related parts for wear while open
Do-It-Yourself Stories from Customers like You
Ice build up on front of icemaker Brian H. • Mccalla , AL • August 06, 2016
REPLACED DISPENSER CRANK ARM, SPRING, FLAPPER FOR DISPENSER. THE REPAIR WAS VERY SIMPLE WITH NO PROBLEMS AT ALL.
Read more
More
$26.95
- Compare At:
-
$32.34
- You Save:
-
$5.39
Genuine Ge part
By: Ge
Part Number: WR01X10618
This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.
- Secures covers, brackets, and trim to the appliance cabinet or liner
- Replaces missing, stripped, or corroded hardware
- Helps reduce vibration noise and loose or misaligned parts
- Maintains proper fit of guards, kickplates, or internal panels
Includes: 1 screw
- Disconnect power; turn off water supply if working near water lines
- Match to the original fastener to size and thread
- Start threads by hand to avoid cross-threading; tighten snugly, not excessively
- If threading into plastic, avoid overtightening to prevent damage
Do-It-Yourself Stories from Customers like You
Water tank leak in refrigerator when using the water dispenser. Stephen B. • Summerville , SC • February 24, 2019
Replaced the water tank. Followed the video instruction provided by Appliance Parts Pros.
Very good instruction.
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR57X57
Nut for 1/4 inch tubing.
Do-It-Yourself Stories from Customers like You
Frigidaire refrigerator model FRS3HR5HMB5 having issues with ice buildup around the evaporator fan have had similar issue for three to four years Keith C. • Cypress , TX • November 12, 2018
Changed the Frigidaire Icemaker Fill Tube Part # 241796405 (AP5671747) about a week ago and so far the Frigidaire Refrigerator seems to work fine. Did not use other ordered parts. Recently ice formed around internal evaporator fan and it started making loud noise when then fan and compressor, etc were running. A long winded history noted below if interested:
I have been fighting with this Frigidaire Refrigerator for about 3 to 4 years, started out with the evaporator fan making noise when ice...
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR1X1367D
Includes 12 retainer rings.
Do-It-Yourself Stories from Customers like You
A fin on the plastic auger broke off and needed to be replaced John M. • Massanutten , VA • August 08, 2015
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went...
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Ge part
By: Ge
Part Number: WR1X5278
This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.
- Anchors wire harnesses in their designed routing
- Helps prevent insulation wear from rubbing or vibration
- Keeps wires clear of sharp edges and moving parts
- Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises
What's included: 1 cable clamp Install notes:
- Disconnect power before servicing
- Access the clamp location and note original wire routing
- Position the clamp and secure with the existing fastener; do not overtighten
- Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR2X7309
This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.
- Secures the solenoid to its housing or frame to prevent shifting
- Maintains proper alignment for reliable actuation
- A worn or broken saddle can cause buzzing/chattering and intermittent operation
- Restores stable mounting to help the connected mechanism work correctly
What's included: 1 solenoid saddle Install notes:
- Disconnect power; shut off water supply if working near water lines
- Access the solenoid assembly and note the original saddle's orientation
- Transfer the solenoid into the new saddle and reuse existing fasteners/clips
- Smooth operation before reassembling panels
Do-It-Yourself Stories from Customers like You
Ice dispenser crushing ice only no cubes Eric W. • Copper Canyon , TX • June 27, 2014
Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair.
Read more
More
$6.72
- Compare At:
-
$8.36
- You Save:
-
$1.64
Genuine Ge part
By: Ge
Part Number: WZ4X241D
Includes 12 screws. Size: 8-18 ab.
Do-It-Yourself Stories from Customers like You
We didn't have a power cord for our dryer Heather B. • Dulce , NM • October 27, 2018
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you.
Read more
More