Kenmore Washer Dryer Combo 417.97804790 (41797804790, 417 97804790) Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303207102
The Door Strike is an OEM part for Frigidaire dryers. It is a small, essential component that ensures the dryer door remains securely closed during operation. The door strike engages with the door catch to keep the door latched, allowing the dryer to operate efficiently and safely. Without a functioning door strike, the dryer may not start, or it could stop mid-cycle.
You should replace this door strike if it becomes damaged or worn out. Over time, the door strike can suffer from wear due to regular use, misalignment, or accidental impact, leading to issues with the dryer door latching properly.
Symptoms of a bad door strike include:
- The dryer door not staying closed
- The dryer not starting or stopping unexpectedly
- Difficulty in latching the dryer door
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Frigidaire dryer door would not stay closed Carolina L. • Miami , FL • September 08, 2015
My dryer door would not stay shut because the door strike was stuck in the door catch. I was afraid that when I pulled the strike out, it would damage the catch, so I ordered the door strike and door catch.
I got the damaged door strike out with needle nosed pliers in about 15 seconds. The door catch was in perfect condition so I didn't need to use the one I ordered. So then I proceeded to install the new door strike. That took me about 15 minutes because I did not have the manual strength to...
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Frigidaire part
By: Frigidaire
Part Number: 131873304
The Dryer Timer Knob is an OEM part for Frigidaire dryers. It is responsible for allowing users to set the drying time and cycle selection by turning the timer shaft. The knob securely attaches to the timer and provides an easy way to control dryer settings.
Over time, the timer knob can become damaged due to repeated use, excessive force when turning, or wear on the internal connection points. If the knob becomes stripped, cracked, or no longer stays in place, it may need to be replaced.
Symptoms of a bad timer knob include:
- The knob spins freely without adjusting the timer
- Cracks or breaks in the knob
- Difficulty selecting or changing dryer settings
- The knob does not stay attached to the timer
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
The dryer knob cracked and no longer turned the dryer on Patty G. • Lexington , SC • November 02, 2015
The old knob was not repairable. I ordered a new knob for the washer dryer stack unit. The order came within two days of ordering and it was the correct part. I was pleased.
Read more
More
$49.95
- Compare At:
-
$58.94
- You Save:
-
$8.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 134399700
The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes are dried according to the selected specifications.
Symptoms of a bad Start Switch include:
- The dryer not starting when the switch is pressed
- Intermittent starting issues, where the dryer sometimes starts and sometimes doesn’t
- The need to hold the switch in place to keep the dryer running
- Unusual noises when the switch is pressed
Causes for a malfunctioning Start Switch can include electrical issues, such as faulty wiring or connections, wear and tear from frequent use, or internal failures within the switch mechanism that prevent it from signaling the motor to start.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers.
Do-It-Yourself Stories from Customers like You
Start switch knob broke off. Jeff O. • Laurier , WA • March 07, 2018
I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$
easy peasy!! :-)
Read more
More
$64.95
- Compare At:
-
$77.29
- You Save:
-
$12.34
Genuine Frigidaire part
By: Frigidaire
Part Number: 131724301
The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.
Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.
Symptoms of a bad drum bearing bracket include:
- Excessive vibration or shaking during operation
- Loud grinding or scraping noises
- The dryer drum not spinning properly or at all
- Premature wear of the drum bearing
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$9.63
- Compare At:
-
$11.36
- You Save:
-
$1.73
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281019
The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.
Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage.
Symptoms of a bad dryer ball include:
- Squeaking or grinding noises during operation
- The drum not rotating smoothly or becoming unbalanced
- Increased friction leading to higher energy consumption
- Visible wear or damage to the ball
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$12.95
- Compare At:
-
$15.28
- You Save:
-
$2.33
Genuine Frigidaire part
By: Frigidaire
Part Number: 131168200
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
- Fastens components to frames, brackets, and covers
- Replaces missing, damaged, or rusted screws
- Helps reduce looseness, vibration, and rattling noises
- Restores proper alignment of panels and assemblies
What's included: One screw
- Disconnect power before servicing; shut off gas/water if applicable
- Start the screw by hand to avoid cross-threading; use the proper driver
- Tighten snugly—do not overtighten to prevent stripping metal or plastic
Do-It-Yourself Stories from Customers like You
Grill on air duct had an item melt on to it and partially block air flow Charles C. • Orchard Park , NY • November 25, 2017
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube.
I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to...
Read more
More
$19.95
- Compare At:
-
$23.94
- You Save:
-
$3.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 134548800
The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.
Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.
Symptoms that may indicate the need for a replacement leveling leg:
- Uneven or unstable washing machine
- Excessive shaking or vibration during spin cycles
- Difficulty in leveling the washer during installation
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Water leak under tub Hector D. • Lubbock , TX • December 07, 2014
After watching YouTube videos on possible cause, went to appliancepartspros and order seal and leveling legs since the had been missing since machne was given to us. Parts came in within the week and replaced . No more leaks!!
Read more
More
$20.45
- Compare At:
-
$24.34
- You Save:
-
$3.89
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304488479
This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.
- Holds a hose, tube, or duct firmly to its fitting
- Helps maintain a sealed connection under vibration
- Helps resolve loose connections, drips/moisture at a joint, or rattling noises
- Common wear includes loss of tension, corrosion, or visible damage
What's included: 1 clamp Install notes:
- Disconnect power; if servicing a water line, shut off the water supply
- Note the original clamp position and orientation before removal
- Use appropriate hand tools (pliers, screwdriver, or nut driver as applicable)
- After installation, test for leaks or movement
Do-It-Yourself Stories from Customers like You
Fan making banging sound in housing Keith N. • Kaukauna , WI • April 25, 2015
The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Frigidaire part
By: Frigidaire
Part Number: 131212301
The Capacitor is an OEM part for Frigidaire washing machines. This part stores and releases electrical energy to start and maintain the operation of the washer's motor, ensuring it runs smoothly during wash and spin cycles.
Causes of a bad capacitor can include electrical surges, general wear and tear over time, or exposure to high temperatures and moisture.
Symptoms of a bad capacitor include:
- The washer not starting or having difficulty starting
- The motor running intermittently or not running at all
- Unusual humming or buzzing noises from the washer
- The washer stopping mid-cycle or not completing cycles
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Top loading washer would not agitate or spin h20 out after a clicking noise; the motor wouldn't engage or would start & then stop finally figured that it was the motor &/or capacitor Susan S. • Pelkie , MI • October 31, 2014
I found your site which was most helpful. I saw on your forum, that others had replaced a motor & capacitor with + results. I was willing to spend what I thought was a reasonable amount & your guarantee was the clincher. I knew that if I called the appliance store where we had purchased the washer in 1998, it would be very expensive & even more important, it would take many days as they would have to order the part & then schedule a service call. I installed the motor & capacitor & was...
Read more
More
$15.50
- Compare At:
-
$18.45
- You Save:
-
$2.95
Genuine Frigidaire part
By: Frigidaire
Part Number: 131302800
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
- Fastens the drum baffle/lifter (vane) to the rotating drum
- Helps maintain proper tumble and load turnover
- Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
- Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes
What's included: One screw
- Disconnect power before servicing; shut off gas
- Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
- Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
- Start all screws before final tightening to seat the baffle evenly
Do-It-Yourself Stories from Customers like You
The pump hose had a tear in it and the water hoses were in bad shape Steven V. • El Cerrito , CA • September 21, 2014
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy
Read more
More
$17.95
- Compare At:
-
$21.54
- You Save:
-
$3.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 131719100
This dryer timer is the cycle control that advances your dryer through Timed and Auto Dry settings. Replacing a failed timer restores proper cycle progression, start/stop, and end-of-cycle shutoff.
- Advances the cam and internal contacts to move the dryer through heat, motor, and cool-down steps
- Governs run time on Timed Dry and Auto Dry cycles
- Routes power to the correct circuits in sequence; a failed timer may not advance or may stop early
- Common symptoms include timer knob not moving, dryer running indefinitely, or not starting on certain settings
What's included: 1 dryer timer assembly Install notes:
- Disconnect power; for gas models, also shut off gas
- Remove knob/dial, open the console, and unmount the timer
- Label or photograph wiring; transfer wires one at a time to the new timer
- Reassemble and test both a Timed Dry and an Auto Dry cycle
This part fixes the following symptoms
-
Doesn't shut off
-
Timer will not advance
See more...
Do-It-Yourself Stories from Customers like You
Dryer timer would not turn and knob broke from the strain Bruce B. • Birmingham , AL • October 17, 2014
I ordered the timer and knob on Monday, they arrived around noon on Tuesday, and within an hour I had them installed and back in business. I was amazed how quickly the parts got here. The online video showing the procedure step by step was very helpful. Instead of disconnecting all the wires and having to keep up with which one went where, I moved each wire one by one and made sure I didn't get any of them in the wrong place. The only thing that slowed me down a bit was seeing which side of the...
Read more
More
$180.52
- Compare At:
-
$216.62
- You Save:
-
$36.10
Genuine Frigidaire part
By: Frigidaire
Part Number: 137551901
This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:
- Forms a tight seal between components or housings
- Helps prevent water drips, seepage, or air leaks at the joint
- Maintains correct appliance performance by keeping moisture/airflow contained
- Replace if the gasket is cracked, torn, flattened, or misshapen
- Common signs include residue, moisture, or visible gaps around the seal
What's included:
Install notes:
- Disconnect power; turn off the water supply before servicing
- Note the orientation of the old gasket prior to removal
- Clean and dry the mating surfaces; remove any old gasket residue
- Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal
Do-It-Yourself Stories from Customers like You
They are 20 year old Bruce A. • Folsom , CA • March 19, 2018
This was more maintenance than a fix. I replaced the door gasket and temp sensor on my dryer. Thought what the heck and it might work more efficiently. I also replaced the shocks on my front loading washer. That was a bit of a chore, but could not have done it without the video that showed how to replace them. The socket was the life saver. All is working just fine. Who knows maybe I'll get another 20 year out of them.
Read more
More
$47.50
- Compare At:
-
$56.05
- You Save:
-
$8.55
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303281020
For a complete drum bearing and shaft kit order 5303281153.
Do-It-Yourself Stories from Customers like You
Dryer drum would not turn J Kent I. • Anderson , IN • February 22, 2019
I watched the helpful diy video. It gave me what the problem was and the confidence to do it. Took my dryer apart with the helpful hints in the video repair went smooth. Works like a dream and I saved money. Thank you appliance parts pros.
Read more
More
$12.95
- Compare At:
-
$15.54
- You Save:
-
$2.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 131268401
By Frigidaire. 27 inch models, 1990 and up.
Do-It-Yourself Stories from Customers like You
Frigidaire washer not draining water and loud noise while trying to drain water Tolga A. • Sammamish , WA • September 18, 2015
When I removed a bunch of very wet soaking towels at the end of a wash cycle, it was clear that the water was not draining properly. The washer also made a very loud noise during the water drain period. That was suspicious. I ordered the part, opened the washer, removed the old pump and faced with a nasty surprise.
You may laugh at this, but there was a toothpick in the old drain pump! most of it was still there, and it seemed like the toothpick was stuck in the pump in such a position that it...
Read more
More
$187.41
- Compare At:
-
$223.02
- You Save:
-
$35.61
Genuine Frigidaire part
By: Frigidaire
Part Number: 134159500
The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.
Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.
Symptoms of a bad drive motor include:
- The washing machine not spinning or agitating
- Loud, unusual noises during operation
- The washer not starting or stopping mid-cycle
- Burning smell or visible signs of motor overheating
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Motor died on washer Timothy P. • Los Angeles , CA • July 27, 2014
I took the easy fix first and replaced the Capacitor. That got me three loads before the motor burned out. I ordered the motor from AppliancePartsPros.com after a google search for "best price model # 134159500 Drive motor " The part arrived in 5 days, and it took about 15 minutes to remove the old motor and replace it with the new one. Simple and easy. four screws, four nuts, and two electrical connections. — The hardest step was one of the four mounting screws was way back inside and it took...
Read more
More
$298.70
- Compare At:
-
$355.45
- You Save:
-
$56.75
Genuine Frigidaire part
By: Frigidaire
Part Number: 5303937189
Includes motor, motor pulley and housing. Motor pulley no longer available separate
Do-It-Yourself Stories from Customers like You
Motor burned Carroll B. • Niceville , FL • February 08, 2015
I replaced the motor. It was time consuming because you have to take all of the parts that attach off. Was fairy simple. Pleased about the parts delivery. Ordered and received the next day.
Read more
More
$174.95
- Compare At:
-
$206.44
- You Save:
-
$31.49