Kenmore Refrigerator 596.67953602 (59667953602, 596 67953602) Parts

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

• Noisy

I pulled the refrigerator out, removed the back panel, disconnected the fan motor. I did not know how hard or easy it would be to remove the fan from the motor shaft so I removed the motor with the fan attached and then removed and replaced the fan. This would not be necessary if you have a lot of strength, but if you need leverage to push the fan down on the shaft you might want to disconnect and remove the motor fan assembly too. After replacing the motor assembly and reconnecting I tested by... Read more

Replaced It With New One Read more

Touch up paint Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

I ordered parts and replaced them. Service was great and fast, plus original parts. Thanks Read more

• Freezer not defrosting

My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more

There are videos on You Tube,. After removing the bottom basket, you remove the entire drawer including the door together with it, by using a screwdriver to depress the white clip on each drawer slide which releases the slide from body of the freezer. Once you pull our the entire drawer, you will need to drill out a rivet to remove the old slide. You will need a rivet gun to attach the new slide. Read more

I had verified that the water supply was healthy, so it was either the icemaker unit or the water valve. I replaced the icemake first, based on a the pareto showing it was the culprit for most other people, but it didn't help. That replacement was straightforward; the hardest part was reaching all the way back to unclip the wiring harness since I am too lazy to totally empty the bottom freezer and remove the door. So the next step was the water valve. The hardest part of this was pulling the... Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more

The right door on our Jenn Air French Door Refrigerator would pop open & not fully close when the left door was closed first. Called the local distributor/dealer who advised me that the magnetic door gasket probably needed replacement (cost $300.00 + for the repair) What??? Visited you web site where I noted the right door had a "closure & bushing" on the bottom of the door. Could it be this was the problem fix? Took the right door off & examined both pieces. Sure enough the bushing was... Read more

Replaced icemaker and shutoff arm. Easy project. Read more

There is nothing you can't do given the right YouTube video! We disassembled the bottom mount freezer n our Jenn Air refrigerator to remove all the ice and then located the clogged grommet on the back of the unit and cleared it and added a notch. In the process of reassembling we broke the bracket on a part that should have been the easiest portion of the entire installation! In seconds we located and ordered the part on your site. It arrived in a couple of days and then we removed the door and... Read more

I removed old crisper and put new one in with the new center crisper rail. I watched one of your videos and I did it all by myself and I even posted it on my social media post Fuentesfab@Instagram Read more