Kenmore Dishwasher 665.1571590 (6651571590, 665 1571590) Parts

Restore smooth loading and secure placement for your dishes with this replacement dishrack. Replacing a bent, rusty, or damaged rack helps keep items upright, improves spray coverage, and prevents flaking or broken tines from contaminating the wash. What it does

• Holds and organizes dishes, bowls, and cookware during the wash cycle
• Slides on the rail system for easy loading and unloading
• Helps maintain proper spray coverage and drainage for effective cleaning
• Common symptoms of failure: rusted or broken tines, peeling rack coating, rack wobbling or derailing, poor rolling, items tipping over

What's included

• 1 dishrack

Install notes

• Disconnect power and shut off water; open the door and fully extend the rack
• Remove rail stop clips/end caps as applicable and slide out the old rack; wear gloves to avoid cuts from sharp edges or rust
• Transfer any reusable accessories (silverware basket, clips, holders) from the old rack if needed
• Slide the new rack onto the rails, reinstall the stops, and verify it glides smoothly before running a cycle

Screw for wash impeller.

This dishwasher drain hose kit includes a clamp with instructions.

This lower spray arm assembly circulates pressurized wash water across the bottom rack to help remove food soil and improve cleaning. It replaces a worn or damaged lower arm to restore proper spray coverage. What it does:

• Directs water flow from the pump to wash dishes on the lower rack.
• Helps maintain even spray pattern and consistent cleaning performance.
• Can prevent poor cleaning or missed spots caused by cracked, clogged, or broken arms.
• Connects to the dishwasher's spray tube or hub to rotate during the wash cycle.

• Disconnect power to the dishwasher before servicing.
• Remove the lower rack to access and remove the old spray arm; typically snaps or unscrews from the hub.
• Inspect the spray arm hub and spray tube connection for debris before installing the new arm.
• Reinstall the lower rack and run a short cycle to verify proper rotation and no obstructions.

This premium dispenser cam engages the dispenser mechanism to control door/lever movement and ensure reliable dispense actions. It replaces a worn cam to restore proper dispenser function and consistent operation. What it does:

• Rotates and times the dispenser lever/door so the dispenser opens and closes correctly
• Transfers motion from the actuator to the dispenser linkage or switch
• Commonly used when the dispenser lever feels loose, doesn't return, or dispensing is intermittent
• Helps stop unwanted continuous dispensing caused by a worn cam surface

• Disconnect power (and water supply if applicable) before starting work
• Access the dispenser assembly; removal of the dispenser bezel or control housing may be required
• Handle small plastic parts carefully to avoid breaking tabs; align cam on shaft before reassembly
• Test dispenser operation after reassembly to ensure correct movement and sealing

Size: 8-32 x 1/4 inch.

This lower wash arm bearing keeps the dishwasher's lower spray arm turning smoothly so dishes get even water coverage. It replaces a worn bearing to reduce noise and restore proper spray-arm rotation. What it does:

• Supports the lower spray arm so it can spin freely during cycles
• Helps maintain even water distribution for better cleaning
• Reduces grinding or scraping noises caused by a worn bearing
• Prevents wobbling or misalignment of the lower spray arm

• Disconnect power and shut off the water supply before starting any repair
• Inspect the spray arm and mounting surfaces for damage; clean before installing the new bearing

The Latch Switch Kit, an OEM Replacement Part is designed to ensure the safe operation of your Whirlpool dishwasher. The kit includes two microswitches and a wiring harness. It prevents the appliance from running when the door is open. If defective, the door switch may prevent the dishwasher from operating even when the door is closed.

Causes of a bad door switch can include wear and tear, exposure to moisture, or a broken actuator.

Symptoms of a bad door switch include:

• Dishwasher not starting
• Dishwasher stopping mid-cycle
• Error codes related to door issues
• Dishwasher running with the door open

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black. Includes insulation. Other colors: For almond use WP3384157, for biscuit use WP3384157, for white use WP3379921.