Kenmore Dishwasher 665.15979992 (66515979992, 665 15979992) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10348409
This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.
- Provides threaded fastening for panels, brackets, covers, or internal components
- Replaces worn, rusted, stripped, or missing hardware
- Helps reduce vibration and rattling from loose parts
- Restores proper alignment and a secure fit of attached parts
What's included: Includes 1 screw. Installation notes:
- Disconnect power; turn off water supply before service
- Note original screw location and retain any spacers or clips for reassembly
- Start threads by hand to avoid cross-threading
- Tighten snugly; do not overtighten to prevent stripping
Do-It-Yourself Stories from Customers like You
Dishwasher would not start Mark M. • Midlothian , VA • July 16, 2016
Maytag Dishwasher (about 5 years old). Some of the buttons had stopped functioning. Then the Start button began choosing whether or not to work. Eventually it would not start at all. Upon removing the control panel, the first thing I noticed was that the brackets that hold the two lower screws were broken. (So this was the reason that the door was so hard to open from the time it was new.) I trouble shot the thermal fuse, the door-latch switches, and inspected the control board trying to find...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
Leaking around dishwasher door previous repair missing parts Patrick R. • Peachtree City , GA • November 15, 2014
I ordered new seals from AppliancePartsPros.com. Finding the right seals was very easy, all based on model number of the appliance. While looking my unit over for other signs of wear, I noticed that a repair done by the prior homeowner to the lower wash arm was done improperly: a seal there was set protruding from the cover, the cover was missing screws, and the arm was missing the upper bushing. So I ordered a new seal, the missing screws, and both the top and bottom bushings (just to be...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10616003
The Dispenser Assembly is an OEM part for Whirlpool dishwashers. It is responsible for dispensing detergent and rinse aid at the appropriate times during the dishwashing cycle, ensuring optimal cleaning and drying performance. The assembly includes compartments for detergent and rinse aid, which are released automatically by the dishwasher.
Causes of a bad dispenser can include clogging or blockage in the dispenser mechanism, damage to the dispenser door or latch, or malfunctioning electronic components that control the dispensing process.
Symptoms of a bad Dispenser Assembly include:
- Improper dispensing of detergent or rinse aid
- Insufficient cleaning or rinsing results
- Leaks or drips from the dispenser area
- The dispenser door not opening or closing correctly
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
This part fixes the following symptoms
-
Will not dispense detergent
See more...
Do-It-Yourself Stories from Customers like You
Soap dispenser door would not latch closed Lee J. • Lumberton , NJ • January 27, 2015
Looked online for a replacement soap dispenser. Found one on several sites but The A.P.P. site showed the part on a Parts breakdown page and showed the part item number. and the actual part number. I ordered the part and expected the part to show up in about 5-7 days, as per the receipt. The part showed up in 2 business days. I installed the part and the dishwasher works as new. Thanks A.P,P.
Read more
More
$164.43
- Compare At:
-
$197.32
- You Save:
-
$32.89
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8268874
This lower spray arm assembly circulates wash water from the pump to clean dishes on the lower rack. The integrated shield helps direct water flow and protect the arm from debris, restoring consistent wash coverage.
- Distributes high-pressure water across the lower rack for effective cleaning
- Shield design helps prevent debris intrusion and improves spray pattern
- Common failure signs: poor lower-rack cleaning, noisy or restricted rotation, cracked or warped arm, clogged spray holes
- Also addresses leaking or splashing caused by a damaged or misaligned arm/shield
What's included: One lower spray arm with attached shield Install notes:
- Disconnect power and turn off water supply before servicing
- Remove lower rack; lift off old arm assembly per model design
- Clear any debris from pump outlet and sump before installing
- Ensure the new arm spins freely and is fully seated; test for smooth rotation
Do-It-Yourself Stories from Customers like You
Dishwasher was noisy not cleaning well and spray arms were loose Steve S. • Rochester , MN • September 10, 2016
Replaced upper and lower spray arms, plus nylon bearings.
Read more
More
$70.76
- Compare At:
-
$84.91
- You Save:
-
$14.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9740674
This drain cover gasket seals the drain/pump cover at the bottom of the dishwasher tub to keep wash water contained. Replacing a cracked or flattened gasket helps stop leaks from the base and protects nearby components.
- Creates a watertight seal between the drain cover and sump opening
- Helps prevent leaks onto the floor or into the dishwasher base during cycles
- Common signs of failure: puddles beneath the unit, dampness in the base, or a visibly hardened/cracked gasket
- Good practice to replace when the drain cover is removed for service to ensure a proper reseal
What's included: 1 drain cover gasket Install notes:
- Disconnect power and shut off water supply before servicing
- Remove the lower rack (and spray arm if required) to access the drain cover per your model
- Clean mating surfaces; install the new gasket evenly without twists
- Reassemble and run a short cycle while checking for leaks
Do-It-Yourself Stories from Customers like You
Debris got into the impeller and broke it Thomas L. • Westport , MA • November 30, 2014
Replaced the drain & wash impeller kit.
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3378186
Dishwasher middle wash arm manifold tube holder. This holder will have a split at the 3:00 position for easy removal from the manifold tube.
Do-It-Yourself Stories from Customers like You
Threer issues broken tine clips broken soap dispenser door latch and broken manifold tube Edward S. • Youngstown , OH • September 26, 2017
All of these items went on quickly. The Soap Door latch was the most time consuming but it only took 15 minutes!
Read more
More
$22.95
- Compare At:
-
$27.31
- You Save:
-
$4.36
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3373234
This dishwasher door spring bushing—also called a door spring bearing—sits at the spring's frame anchor to provide a pivot and reduce wear. Replacing a worn bushing restores door balance and helps prevent the door from dropping or slamming open.
- Provides the pivot/anchor surface for the door spring at the cabinet frame
- Maintains balanced door opening and closing force
- Reduces friction, wear, and squeaks at the spring connection
What's included: Includes 1 bushing. Install notes:
- Disconnect power at the breaker and shut off water supply.
- Remove the toe panel and mounting screws; slide the dishwasher out slightly to access the door springs.
- Support the door, release spring tension, replace the bushing at the frame anchor, and reattach the spring.
- Inspect both sides and replace worn components in pairs to keep door tension even.
Do-It-Yourself Stories from Customers like You
The dishwasher door spring broke. Rachael T. • Junction City , OR • November 07, 2022
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached...
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: 8194582
includes seal
Do-It-Yourself Stories from Customers like You
Pump needed replacement cause nut that holds it on melted to the threads. Deborah S. • Lincoln , NE • November 06, 2017
Replaced nut and then found we needed new pump.
Read more
More
$52.33
- Compare At:
-
$62.80
- You Save:
-
$10.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302710
This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.
- Forms a tight, continuous seal at the inlet base-to-housing joint
- Helps preserve correct airflow through the inlet path
- Blocks liquids, grease, and crumbs from leaking into the appliance interior
- Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps
What's included: One inlet base seal.
- Disconnect power to the appliance before servicing
- Remove grates/cartridges, filters, or trim as needed to access the inlet base
- Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
- Reassemble and verify the seal sits evenly with no gaps
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$6.63
- Compare At:
-
$7.89
- You Save:
-
$1.26
Genuine Whirlpool part
By: Whirlpool
Part Number: 4392899
Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.
Do-It-Yourself Stories from Customers like You
Lack of accurate control on 2 electric range burners Jeff D. • Neenah , WI • April 09, 2016
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job.
The fix only took about 15 minutes because I was prepared after watching the video.
Read more
More
$17.76
- Compare At:
-
$21.31
- You Save:
-
$3.55
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3374077
Size: 7 foot long.
Do-It-Yourself Stories from Customers like You
Bought a used dishwasher in excellent shape that needed the drain pieces to get it going Johnny R. • San Antonio , TX • April 14, 2015
Bought the parts and connected same...a breeze in finding and receiving and eventually installing these parts.
Read more
More
$62.78
- Compare At:
-
$74.71
- You Save:
-
$11.93
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP719929
This small check ball sits inside a check valve to allow one-way water flow. Replacing a worn or missing ball helps prevent backflow and supports reliable draining performance between cycles.
- Maintains one-way flow through the valve to stop water from returning after the pump stops
- Helps ensure complete, consistent draining
- A damaged, swollen, or missing ball can let water back up into the tub/sump
- Contribute to slow or intermittent draining and unusual gurgling/flow noises
What's included: 1 check ball. Install notes:
- Disconnect power and shut off water before servicing
- Access the check valve assembly per your model's service information (commonly at the sump, pump outlet, or drain connection)
- Clean the valve seat/passage; remove debris that could prevent sealing
- Place the ball in the valve seat as shown in your model's parts diagram; reassemble and test for leaks and proper flow
Do-It-Yourself Stories from Customers like You
Dishwasher didn't drain Frank C. • Mcallen , TX • June 02, 2016
Cleared out trash from pump.
Made E-Z by your exploded views and videos. Replaced worn parts.
Read more
More
$6.95
- Compare At:
-
$8.34
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84